Noise Monitors
-
Product
RF Monitor Recertification
-
The use of RF personal monitors is widespread among wireless tower climbers and technicians. This is a relatively new development of the last five years or so. Prior to that, only a few monitors were in use. These were typically models developed for use by engineers, with a host of features not needed for routine climber protection. Consequently, they were expensive and not frequently used. As safety managers have begun to require all personnel working on wireless facilities to have personal monitors among their personal protective equipment, a new generation of cost effective equipment has emerged.
-
Product
Portable Temperature Monitor
PTM1
-
The Model PTM1 is a high performance, precision hand-held instrument for the measurement of temperature using Physitemp’s Type T (copper-constantan) thermocouples (will also accept J & K). This versatile instrument measures temperature in both °C and °F. The internal memory of the microcomputer stores the minimum and maximum measured temperature range for instant recall via the LCD display.
-
Product
Thermal Control and Monitoring
-
Harmonize and control your entire data center thermal management system to achieve up to 50% higher efficiency, improve protection and security and enhance staff productivity.
-
Product
Gas Monitor
ULTIMA® X5000
-
The ULTIMA® X5000 Gas Monitor is the future of gas detection for oxygen, toxic and combustible gases. MSA XCell® gas sensors with TruCal® technology offer calibration cycles up to 24 months (local calibration respected).
-
Product
Total Organic Carbon Monitor
HT-110
-
The continuous online TOC-Analyzer HT-110 is suitable for the measurement ot total organic carbons in Purified Water (PW), Water For Injection (WFI) and Highly Purified Water (HPW). The unit is operating according to USP 643. It is applicable for pharmaceutical and/or semiconductor manufacturing. The measuring principle is based on UV-Oxidation and measurement of the difference in conductivity. TOC concentration measurement (TOC concentration 500 ppbC or lower) is necessary to perform quality control according to GMP (Good Manufacturing Practice).
-
Product
Millimeter-Wave Noise Source, R-band, 26.5 to 40 GHz
R347B
Noise Source
The Keysight R347B noise source covers a 26.5 to 40 GHz frequency range. This waveguide noise source allows you to make accurate and convenient noise figure measurements on millimeter-wave devices. The R347B provides highly precise broadband noise at the input of the system or component under test. The noise figure meter then processes the ON/OFF ratio of noise power present in the system IF, and provides an accurate reading of noise figure and gain. The R347B noise source has remarkable ENR stability over time, which allows longer recalibration cycles and more accurate noise figure measurements.
-
Product
Network Monitoring Services
-
Products such as IntraVUE™ Software and SynapSense® Monitoring Systems, deliver optimal solutions for documenting and monitoring your plant floor, data centers, and other Network Infrastructure applications.
-
Product
Monitoring Systems
-
Once a dynamic event is detected, the system instantly informs the control system or other external devices and acts as a digital recorder by capturing important data before and after the event. This information can be used to alert the operator to change process settings or schedule maintenance.
-
Product
Leakage Current Monitor
-
To alert utility-line workers of overcurrent conditions on such aerial devices as insulated ladders and truck booms, the Chance Sentinel sounds an alarm if leakage current reaches a pre-set level.
-
Product
Temperature Monitor
SIM922A
-
Stanford Research Systems, Inc.
The SIM922A has a programmable, precision 10 µA current source to provide sensor excitation. Results can be displayed in either kelvins or volts.
-
Product
Clamp type AC Current Sensor／for Power Monitor
ZCT-33
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 0.1A～150A*Current measurements of feeder
-
Product
Three Phase Power Monitoring
-
PRÜFTECHNIK Condition Monitoring GmbH
A three-phase power monitor detects changes in electrical variables. With power monitoring on your assets, you can help reduce wear and damage, while also identifying what’s causing it. The Fluke 3540 FC three-phase power monitor can be used remotely or through a stationary connection.
-
Product
Multi Wavelength Monitor
LV5490/LV5480
-
The LV 5490 is a multi waveform monitor that supports 4K video format (4096×2160、3840×2160) based on 3G-SDI dual link or quad link, HD-SDI quad link, and 12G-SDI. The following two 4K video division transmission systems are supported. ・2-SAMPLE INTERLEAVE DIVISION ・SQUARE DIVISION
-
Product
Two Way Monitoring and Control
-
The Drexelbrook 560 DRX Series wireless products feature 900KHz frequency hopping, spread spectrum technology to provide a reliable, license free, wireless link between the field instrument and the control room.These wireless interface products provide a cost effective alternative to expensive hard wired connections.Using Frequency Hopping Spread Spectrum (FHSS) technology, a robust signal is provided that is virtually free from disruption due to interference.
-
Product
AM Monitoring System
I3MS
-
High-speed infrared imaging monitoring system for quality assurance of industrial processes
-
Product
Occupational Noise Measurement System
NK122
-
This Occupational Noise Measurement System is designed to give Health and Safety Managers, or any other professional with responsibilities for managing noise in the workplace, everything they need to protect your workforce from over exposure to noise and to help you ensure your company is complying with The Control of Noise at Work Regulations 2005.
-
Product
Bulk Current Monitoring Probe
MP-50
-
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
Product
PDS Wire Crane Monitoring System
-
It shows a real time overview of the wire crane in navigation, profile, and 3D views; displaying the clamshell, pontoon/vessel, design depths and color-coded digital terrain model (DTM). The navigation view highlights the high and low spots and is updated in real time, registering the progress of the dredging work. The registration follows the shape of the clamshell, bucket or orange peel bucket and is visible immediately in all views. The system also shows the open/close status of the dredge tool. Up/down indicators show the operator the exact distance to the seafloor and design depth continuously. 3D design models allow the use of complex designs.
-
Product
Particle Impact Noise Detection
BW-LPD-DAQ4000
-
Computer based controller with predefined MIL-STD test sequences stored (New)Create unlimited custom tests with multiple vibration frequencies and acceleration and other parameters to meet unique requirements (New)
-
Product
Server Configuration Monitor
-
Detect and compare configuration changes to your servers, databases, and applications
-
Product
Respiration Monitor Belt Logger Sensor
NUL-236
-
This sensor comes with a belt and measures the air pressure in it. The pressure changes according to the breathing of the subject. From the measured values, the respiration rate can be calculated.
-
Product
Thermalert Monitoring Thermometer
TH-8
-
The TH-8/AOP is one of our most economical precision thermometers in the Physitemp product line. The TH-8 offers the same high accuracy (0.1°C ±1 digit) and resolution as all our other thermometers, but with a narrow temperature range. The TH-8 has a temperature range 0f -10 to +60°C with 3 probe inputs. The TH-8 is also switchable from celsius to Fahrenheit. The TH-8 is ideally suited for either a laboratory or hospital setting where continuous temperature readings within the physiological range are sufficient.
-
Product
Ultra-Low Noise 2 kHz Photoreceiver w/ Si-PIN Photodiode
PWPR-2K-SI
-
Picowatt Photoreceiver series PWPR-2K with switchable gain (10 to the 9th V/A, 10 to the 10th V/A) and a bandwidth from DC to 2 kHz is the perfect choice for cw-measurements, time resolved signal acquisitions and highly sensitive modulated measurements. Si and InGaAs models cover the wavelength range from 320 to 1700 nm.
-
Product
24/7 Monitoring
-
Provides a centralized overview of the Service Availability and Video Quality throughout all the strategic stages of the media processing & delivery flow.
-
Product
APPLICATION INFRASTRUCTURE MONITORING FOR CUSTOM WEB APPLICATIONS
VMware vFabric
-
Each Hyperic plug-in tracks dozens and sometimes hundreds of metric values per server plus events, log entries, and configuration file changesfor each monitored technology, unlike other tools that only report OK, WARNING, CRITICAL, or UNKNOWN.
-
Product
Remote Monitoring & Lubrication
-
Remote Monitoring and Lubrication Products remove the guesswork from your maintenance practices so you stay in control of your equipment’s health
-
Product
Real Time Monitoring Of Windows Server
GSX for Windows Server
-
Monitor and troubleshoot operating systems and related applications from a single dashboard. Windows servers and services are fueling mission-critical applications, so having visibility into the status of their health and usage is essential. By continuously testing the availability and performance of the Windows server and its applications, GSX enables proactive management of the IT environment. End-to-end monitoring improves the end-user experience, reduces mean-time-to-repair, and helps administrators to prevent issues before they happen.
-
Product
Panel-mount Type Peracetic Acid Monitor
PM-960
-
A measurement device for continuous measurement of the concentration of peracetic acid used for sterilization in food and beverage processing. The device uses no reagents and is maintenance-free.
-
Product
Network Performance Monitor
-
*Multi-vendor network monitoring*Network Insights for deeper visibility*Intelligent maps*NetPath and PerfStack for easy troubleshooting*Smarter scalability for large environments*Advanced alerting
-
Product
23 GHz Low Noise Amplifier
HMMC-5023
Amplifier
The HMMC-5023 is a GaAs MMIC low noise amplifier designed for moderate gain and low noise from 21 GHz to over 30 GHz. Typical applications of the HMMC-5023 include digital radio communications systems that operate within the 21.2 GHz to 23.6 GHz and 24.5 GHz to 26.5 GHz frequency bands. Moderate gain and low noise temperature make it ideally suited as a front-end gain stage.
