Wafer Level
-
Product
Level Switches
-
In point level detection, a point level switch detects when a certain predefined level is reached. Such a device is employed when it is not necessary to measure every possible intermediate level, as is the case with continuous level measurement. A switching command starts or stops filling equipment such as conveyors or pumps. Point level switches outputting a binary signal can be integrated into a process control system.
-
Product
Wafer Bonder
AML
-
Wafer bonding has found many applications in the field of MST, MEMS and micro engineering. These include the fabrication of pressure sensors, accelerometers, micro-pumps and other fluid handling devices. The process is also used for first-order packaging of silicon microstructures to isolate package-induced stresses. The OAI AML Wafer Bonder facilitates both the alignment and bonding to be performed in-situ, in a high vacuum chamber. For anodic bonding the wafers are loaded cold and heated in the process chamber. For high accuracy alignment the wafers are aligned and brought into contact only after the process temperature has been reached, thus avoiding differential thermal expansion effects which can compromise alignment. The AML Wafer Bonder is excellent for anodic bonding, silicon direct and thermal compression bonding applications. These features enable the bonder to be used with virtually any processing tool.
-
Product
Wafer and Cells PL System
HS-PL
-
Photoluminescence (PL) Imaging is a unique non-invasive inspection tool as it can be used in-line at many different steps of the cell manufacturing process. This facilitates the direct comparison of data obtained at one process step to data obtained at another. Additionally, PL imaging can be compared to electroluminescence (EL) imaging on finished cells using comparable equipment.
-
Product
Liquid Level Sensor
LevelMaster
-
The LevelMaster combines the industry’s most innovative hardware and software to address the unique custody-measurement and operational needs of tank-level management. The LevelMaster provides not only an accurate level gauge, but also an accurate measurement of the oil and water interface.Unlike other level-sensing technologies, LevelMaster provides precise levels without having to continuously adjust for changes in the unpredictable properties of storage-tank liquids. LevelMaster floats can measure oil, water, and emulsion levels up to 25 feet (7.6 m) deep, with a standard relative accuracy of 0.1 inch (2.5 mm) or optional high-precision relative accuracy of 0.05 inch (1.25 mm).
-
Product
Ultrasonic Wafer Scanner
AutoWafer
-
Installed in more wafer applications than all other automatic ultrasonic testing tools combined, AutoWafer provides a complete, production-ready wafer scanner for wafers from 100mm to 200mm, including multiple sizes in a single batch.
-
Product
Precision Sound Level Calibrator
CAL200
-
The Larson Davis CAL200 Sound Level Calibrator is a battery operated precision microphone calibrator used for the calibration of sound level meters and other sound measurement equipment.
-
Product
Wafer Edge Profile Measurement
WATOM
-
WATOM can carry out fully automatic, non-contact measurements of the edge profiles and diameter in accordance with SEMICON standards. A special feature is the system's ability to make measurements of the mark cut into the edge of the wafer to indicate the crystal orientation. Because of its high measurement accuracy of less than 1.5 µm, leading wafer manufacturers across the world use WATOM for shop-floor geometrical quality control.
-
Product
Contact Level Sensors
-
Contact level devices come in contact with the tank media and are used for point or cocntinious level measurement. Types include Float, Optical, RF Capacitence, Conductivity, Ultrasonic, Tuning Fork.
-
Product
In-Process Wafer Inspection System
7945
System
Chroma 7945 wafer chip inspection system is an automated inspection system for pre and post diced patterned wafers. Change kits enable switching between various applications by allowing different carriers including metal frame or grip ring.
-
Product
Wafer Lifetime Measurement with Photoluminescence Detector
WCT-120PL
-
Measure the calibrated carrier-recombination lifetime of a silicon wafer using both the standard method and the photoluminescence meth
-
Product
Sound Level Meters
-
TES Electrical Electronic Corp.
Super high contrast backlight TFT. Compliant with 1 class 2 standard. Real-time 1/1- Octave and 1/3 Octave analysis. Measurement can be started by internal or external
-
Product
Semi-Automatic Contactless Wafer Detector
NCS-200SA
-
Semi-Automatically, non-contact measurement of wafer thickness, TTV ,bow,Point and flatness.Portable and easy to set-up, the Proforma 300/G measures all wafer materials including Silicon, Gallium-Arsenide, Indium-Phosphide and wafers mounted to sapphire or tape.the powerful software can test all the data above within several seconds,all the design according to SEMI standard and the ASTM,make sure the data can be easily unify. the system can used for several sample size,like 75 mm, 100 mm, 125 mm, 150 mm, 200 mm
-
Product
Wafer Probe Test System
STI3000
-
The STI3000 is a wafer-level MEMS and mixed signal ASIC probe test system that combines several functional STI test equipment blocks for testing gyros, accelerometers, pressure sensors, microphones, resonators, and mixed signal ASICs.
-
Product
Sound Level Meters
LXT1-QPR
-
Quantitative measurements of sound pressure levels generated by firearms with & without suppression devices and silencers.Many firearm examiners are tasked with determining whether installation of a suppressor or silencer on a firearm results in a “perceptible” reduction of the sound pressure level of a gun. The Larson Davis SoundTrack LxT® provides this functionality utilizing an easy-to-use handheld platform.
-
Product
Sound Level Meter For Occupational Noise
SONIK-S
-
The SONIK-S helps you protect your workforce from over exposure to noise, and helps you ensure your company is complying with The Control of Noise at Work Regulations 2005.
-
Product
Buoyancy Level Sensors and Switches
-
ABB offers a complete line of buoyancy point level switches for just about any chemical, petroleum or general process application. This family of products include horizontal floats, vertical floats, and displacer switches of all kinds. ABB's simple and reliable design offers great flexibility with custom insertion lengths, temperature ratings to 1000ºF/ 38ºC. Pressure ratings to 5000 psig/345 bar, and a wide selection of alloys. The ABB buoyancy switches are the highest quality and cost efficient solution to industrial liquid level point sensing.
-
-
Product
Shield Level / Pathloss Equipment
PathTrax
-
Identical in form factor to the PAMS and PAMS-C, PathTrax provides an optimum solution for site surveys. Once the receiver is calibrated with the transmitter, the receiver measures path loss directly. PathTrax systems are available to cover several frequency bands each 75MHz wide, centered on 838 MHz, 860 MHz and 915 MHz. A PathTrax centered at 500MHz, covering 25MHz of bandwidth is also available.
-
Product
In-Line Wafer Surface Defect Inspection
ALTO-SD-150/200
-
ALTO-SD SERIES IS AN IN-LINE INSPECTION SYSTEM SUPPLYING HIGH THROUGHPUT, FULL SURFACE DEFECT INSPECTION FOR ALL KINDS OF WAFERS INCLUDING SILICON, QUARTZ, SAPPHIRE, COMPOUND AND MEMS WAFERS. HIGH-RESOLUTION CAMERA OPTICS PLUS LED ILLUMINATION GUARANTEE RELIABLE DETECTION OF ALL LOCAL DEFECTS. IT INSPECTS DEFECT SIZE OF 1~ 10 MICRONS, CONFIGURABLE INSPECTION RESOLUTION TO OPTIMIZE DEFECT SIZE VS. THROUGHPUT. THE SYSTEM COMBINES HIGH-PRECISION MEASUREMENT, POWERFUL DATA ANALYSIS AND USER-FRIENDLY OPERATIONS.
-
Product
Mini Digital Sound Level Meter
PSPL01
-
Frequency Range: 31.5 Hz-8 KHzMeasuring Level Range: 40 to 130 dBAccuracy: +/- 3.5dB @ 1 kHz, 94dB (Under Reference Conditions)1/2" Electret Condenser MicrophoneNewly Designed HousingC-type Frequency WeightingHigh Performance & Auto LCD Backlight50 hrs. Battery LifeAuto Power Off (15 Minutes Inactivity)Sold as : Unit
-
Product
Hopper Ash Level Thermocouple System
HALT
-
The Hopper Ash Level Thermocouple (HALT) System is a preventative maintenance and safety tool that continually monitors the levels of ash within a hopper. As the hopper plugs and the ash levels increase, the thermocouples will become insulated from the boiler heat by the ash. Low temperature readings trigger visual and digital alarms which indicate that the hopper has plugged.
-
Product
Ultrasonic Level Measurement
VeriGAP
-
Ultrasonic technology is a great choice for high or low-level liquid level measurement requirements in a wide variety of liquids. These ultrasonic sensors require no calibration and are not affected by changes in electrical properties of the material being measured.
-
Product
High Resolution Thickness & Surface Profiler for as-sawn Wafers
MX 70x
-
The MX 70x series measure Thickness, Warp, Waviness, Roughness and are usable for nanotopography.
-
Product
Radar Level Transmitter
DR6500
-
The Drexelbrook DR6500 is a two-wire open air radar level transmitter for measuring level in applications with powder and dusty atmosphere.
-
Product
Wafer Test Solutions
-
Wafer Test Solutions has established leadership positions in developing and deploying application-specific test solutions for MEMS devices, offering wafer and frame probing stations suitable for R&D, Wafer Sort, and Final Test. We offer state-of-the-art solutions to test environmental and motion sensors in wafer and other advanced packages.
-
Product
Sound Level Meter
-
The Sound Level Meter is shown positioned near the top of the main Daqarta window. Like the Voltmeter and Frequency Counter, it can be positioned anywhere on the screen, and the size of the display font changes when you resize the meter by dragging its borders. You can fill the screen for a really big readout that can be seen from across the room.
-
Product
Wafer ESD Tester lineup
-
Hanwa Electronic Ind. Co.,Ltd.
◆Correspond to 300mm Wafer. This tester can measure LED or the large sizes Wafer, such as a system LSI. And Zap of HBM/MM can be performed. The Automatic destructive judging by V/I measurement can also be performed after Zap.◆Waveform guarantee in Zap needles. HED-W5100D carries out the calibration before shipment in the place of Zap needles. Therefore, Correlation of the Result of a Package Device becomes clear easily.◆Correspondence to Standards This Tester corresponds to the Standard of JEITA, ESDA, and JEDEC. A Zap unit adopts the plug-in system and also has the waveform of Customer's requests.◆Connection with TLP This Tester is the best for TLP Testing with deep relation of ESD. The protection circuit of a device with an ESD problem is investigated.
-
Product
Water Level Indicator With Alarm Acknowledgement
IM1731
-
We offer Water Level Indicator with Alarm Acknowledgement to our clients.
-
Product
Wafer Thickness, TTV, Bow and Warpage
-
ALTO-TTV FAMILY OFFERS THE SPEEDY MEASUREMENT OF WAFER GEOMETRY PARAMETER, MORE IMPORTANTLY, WE CAN AUTOMATE THE TOOL TO HANDLE FROM THIN WAFERS TO PERFORATED, WARPED, BUMPED, AND TAPE-FRAMED WAFERS. OPTIONAL SORTER AND SHIPPING JAR UNPACKING FUNCTION AVAILABLE.
-
Product
Exposure Level Tester
ELT-400
-
*Wide frequency range (1 Hz - 400 kHz)*Standard-compliant measurement*Acceptance measurements compliant with CE standard IEC/EN 62233 and Generic Standard IEC 62311*Limit value traces conforming to ICNIRP 1998, 2010 and EMF Directive 2013/35/EU*Real time measurement with RMS and peak detectors*External FFT signal analysis for determining the frequency components via three channel analog output (one channel for each spatial axis) e.g. with the aid of a digital oscilloscope.
