Can bus
Controller Area Network
See Also: Serial, I2C, LIN, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus
-
product
Single UTMC BC/RT/M or SUMMIT 1553 Controller
PCI-1553 PLX
The PCI-1553-X uses a single UTMC’s Sµmmit or BCRTM communication device as its 1553 bus controller, or remote terminal, or monitor terminal. The single controller has two redundant channels. This controller accesses 64Kx16 word of external memory and has external for both channel A and B. The 3U PCI board has on-board transformersfor both channels.
-
product
Low Profile PCI 8 Reed Relay Output
8012H
Optimized for sensing 24V inputs, the 8012H Low Profile PCI digital interface provides eight Reed relay outputs (SPST) and eight optically isolated inputs supporting 10-30V. Reed relays are well suited for low current applications. The relays are normally open, and close when energized. The board is MD1 Low Profile and Universal Bus (3.3V and 5V) compatible.
-
product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-6 FPGA - XMC
Model 71651
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- Two 800 MHz 16-bit D/As- One DUC (digital upconverter)- Multiboard programmable beamformer- Up to 2 GB of DDR3 SDRAM or 16 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Front panel clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface up to x8- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
LXI WTB Terminator, 90.6 ohm
60-983-002
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
product
DDR3 MSO Probes
The DDR3 DIMM and SO-DIMM Mixed Signal Interposers connect Address, Command and Control signals of a DDR3 bus to the Keysight V-Series Oscilloscopes with the MSO option. These interposers also provide accessibility to DDR3signals for convenient analog probing.
-
product
Mezzanine Cards
PMC and XMC are the quasi standard for mezzanine cards in VME systems. esd's PMC and XMC modules extend your system with a bus interface (CAN, EtherCAT, Ethernet) or an intelligent sub system (e.g. XMC-CPU/2041, PMC-CPU/440). Furthermore esd develops customized PMC and XMC modules. VME systems without PMC slot can be extended with an esd VME-PMC-Caddy or PCIe-XPIMC-Carrier board.
-
product
Multi-Axis Motion Controllers
DMC-1800
The DMC-1800 for the PCI bus is a member of the Optima Series, Galil's full-featured multi-axis motion controllers. Designed to fit in a single PCI slot of a PC, the DMC-1800 controllers accommodate 1- through 8-axis formats and allow control of step or servo motors on any combination of axes.
-
product
Low Cost Precision Shunt
LPS
This is a precision metal clad resistor designed with four terminals. These models exhibit a high load capacity as well as excellent accuracy. The isolated voltage and current connections make them suitable for very precise current measurements. Direct attachment to current bus and connection to voltage using flexible wires enables easy current measurement.
-
product
T-Coil Magnetometer
The TEM Consulting T-Coil Magnetometer provides an effective solution for measurement to ANSI C63.19 Clause 6 and other magnetic field readings. The system uses a high precision, anti-aliasing digital acquisition PCI bus board for convenient and accurate measurement.
-
product
Eurocard Plugbord
E220-6U-2
VECTOR Electronics and Technology, Inc.
6U x 220mm Eurocard size for 96-pin DIN connectors. Voltage and ground buses around board perimeter on both sides. Bus surfaces solder coated for user convenience. For solder, Wire-Wrap or mixed wiring methods. Row and column legends provided.
-
product
Powered VME Crates
6U VME 6023
The WIENER VME 6023 crate series is the newest generation of 19" integrated packaging system for standard VME/VME64 bus systems with 6Ux160mm cards.Designed primarily for applications in data acquisition, control and test instrumentation it combines superior mechanical quality with lowest noise power supply technology.
-
product
PCIe-6535B, 32-Channel, 10 MHz, 40 MB/s Digital I/O Device
782629-01
The PCIe-6535 can continuously stream data over the PCI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
product
8-Channel 200 MHz, 16-bit A/D with Virtex-6 FPGA - 6U VPX
Model 58660
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Eight 200 MHz 16-bit A/Ds- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
One Wire Communication Board
MS 1727
- Digital serial bus communication with low speed data over a single line, Both signaling and driving power over a same single signal.- Protocol used in small inexpensive devices. Such as digital thermometer, weather instruments, laptop sub module, authenticate system and some cell phone battery packs.- Always master only initiates the communication and in overall in charge of the network.- Bus communicates with master and slave at a low data rate of 12kbps.- All terminals in the network are communicating by half-duplex mode.- Maximum of 255 nodes in each 1-wire network- Each data transaction will start with 480micro second low RESET pulse.
-
product
Avionics Test & Simulation Software
Ballard CoPilot® is an intuitive, graphical software program that allows you to easily monitor, record, replay, analyze, and simulate avionics bus data. With CoPilot you can interact directly with data on multiple buses using Ballard avionics interface hardware or work with previously recorded data. This advanced program features powerful tools for development, testing, troubleshooting and maintenance of avionics equipment and systems.
-
product
ETX Development Baseboard
ETB9F000
The ETB9F000 has four PCI slots and three ISA bus expansions as well as CompactFlash™ Type II socket. Most I/O functions have been integrated into this baseboard.
-
product
Flexible 32-bit PCI Riser
SKU-050-0X
The Flexible 32-bit PCI Riser (Riser) was designed to expand the 32-bit PCI bus into 2 32-bit PCI buses. The Riser includes a PCI adapter (downstream), 32-bit PCI host board and PCI Express Flat cable.The PCI adapter has 2 32-bit PCI slots for plugging in two 32-bit PCI add-in boards. The PCI host board connects to the motherboard PCI connector. The PCI Express Flat cable (12 inches) is used for connecting the host board with the PCI backplane, and it provides a flexible connection between the 32-bit PCI add-in boards and the motherboard.
-
product
1 Channel, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTA
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
PXI 8 Slot BRIC Module, 2 Resource Distributor, 6 Bus Matrix Inputs
40-569B-126
The 40-569B is a range of high-density BRIC matrices capable of switching up to 2A and up to 200VDC/180VAC. These large PXI matrix modules are available with multiple configurations in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays. The 40-569-126 is a 8 slot module fitted with 6 Bus Matrix Inputs cards and 2 Resource Distributor cards.
-
product
Configurable Reostat or Potentiometer Module
YAV90084A
4x 8-Bit 1KOhm reostat4x 8-Bit 40 Ohm reostat2x 8-Bit 5 MOhm reostat10x Electronic Potentiometer 8-bit resolution -256 steps- with build-in self test10x Voltage to current source 0(4)..20mA10x Analog Outputs (buffer for voltage or frequency)36-Ch Test Point voltage divider2xCAN Bus Channels Terminators testerExpandable with NI PXI-6723 and PXI-6345.
-
product
PANAVIA Modules
AIM’s PANAVIA test, simulation, monitoring and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core design with one processor for real time bus protocol support, massive memory and IRIG-B time code encoder/decoder functions are standard. AIM delivers versions of our modules with extended temperature range and conformal coating. With 8 Tx and 8 Rx channels per module, functions include autonomous transmit sequencing, continuous clock and data transmissions, host controlled double buffering, programmable interrupts, data selection on specific tag identifier, selectable triggers on data and/or tags with full protocol error injection/detection, real time bus recording and time stamping to ensure your bus integrity. Each module is delivered with a Board Support Package (BSP) comaptible to the legacy PCI and cPCI hardware modules.
-
product
Digital Services
*Processor verification experience*Memory verification*Bus protocols and DMA verification*Expert in high speed controller verification*Physical layer (PHY) verification
-
product
Multichannel ARINC 429 Interface Device
DAS-429UNET/RTx
Our DAS-429UNET/RTx is an intelligent, multichannel ARINC 429 interface device that can be connected to any Windows device with a USB or Ethernet connector. It monitors and records all or selected 429 traffic for later analysis or reconstruction in the lab. Exalt is our Windows base graphical tool that allows you to analyze real time or recorded data using many different views: raw data, engineering units or graphical displays.Data can be then extracted from the recorded file, and re-transmitted over the bus to another system in order to see in detail what happened during the recorded test.The combination of a handheld computer, 429Unet card and Exalt provides a complete solution for testing and maintaining ARINC-429 networks.
-
product
Analog Output Module For Remote I/O
The Analog Output Module for Remote I/O features a 2-wire spring terminal connection, selectable output ranges (0 V to 10 V, ±10 V, 0 V to 5 V, ±5 V, 0 mA to 20 mA, 4 mA to 20 mA, and ±20 mA) output ranges, and short circuit proof outputs. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Analog Output Module for Remote I/O from a real‐time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low‐cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high‐speed or specialty measurements.
-
product
H009 Modules
M4KH009 modules can operate as a Central Computer Complex (CCC) and/or up to sixteen Peripheral Units (PUs) simultaneously, or as a Bus Monitor. In addition, a Concurrent Bus Monitor enables concurrent monitoring of the bus during CCC and PU simulation. The module also supports error injection and detection, and all control parameters and data may be updated in real time. Note: The M4KH009 Module is a "double size" module, and occupies two vertically adjacent sockets in the EXC-4000 carrier Board.
-
product
MIL-STD-1553 A / B Test And Simulation PCI Module
PCI-C1553
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
40-203-001
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
product
XMC Module
XMC-FPD-xxx
XMC Bus VITA 42• 3.3V I/O, 5V tolerant businterfaces• Local Bus Clock rates at66MHz• Compliant PCIeSpecification, r1.0a x1• Direct slave data transfers• DMA Capability• Up to 160Mb/s Transfer• DMA Transfer per Fifo Level
-
product
*C Series CAN Interface Module
C Series CAN Interface Modules communicate using onboard transceivers for High-Speed/Flexible Data‑Rate or Low-Speed/Fault Tolerant CAN. C Series CAN Interface Modules are either compatible with NI-XNET or the NI-985x driver, depending on model.Using NI-XNET, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series CAN Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
PCI/DSP Module
PCI-4pack-2
The PCI-4pack module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the PCI-4pack is the perfect solution. The Local DSP can be used to simply move data to and from the CPCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc.Custom application software can be downloaded to the DSP via the PCI bus. Windows 95 and WinNT drivers are standard.
