Firmware
-
Product
Firmware for High-speed HDLC Mode
OP-FW10
-
OP-FW10 is firmware to upgrade protocol analyzer LE-7200/LE-3200 to dedicated analyzer that is specialized for High-speed HDLC communication up to 10Mbps. By installing this OP-FW10 to LE-7200/LE-3200, HDLC measurement processing such as the trigger and filter that were processed by software of the analyzer can be replaced to the hardware processing by FPGA built in the analyzer. Therefore, a maximum speed of HDLC supported is vastly improved. After installation of OP-FW10, You can switch to the usual firmware that supports multi protocol by pressing “SHIFT” and “0” keys at the same time when turning on the power of the analyzer. Therefore, it saves you trouble to reinstall firmware.
-
Product
Real-Time Pulse Detection Firmware
FWPD
-
The core challenge in pulse detection is to design a system for random events. The Teledyne SP Devices’s firmware option FWPD, for the ADQ14 and ADQ7, is tailored to detected and analyze pulses in demanding measurement applications where the properties of the pulses (such as timing or length) are not known in advance.
-
Product
Firmware for High-speed Communication
OP-FW12GA
-
OP-FW12GA is the firmware to increase the speed of monitoring test of bit synchronous communication (such as HDLC/SDLC/X.25, or CC-Link communication), SPI communication, Profibus-DP (field bus known for high-speed communication), UART (asynchronous communication, which is commonly used). By processing great part of monitoring processes by FPGA, it unfailingly captures communication data with time stamps of a microsecond rate. The interface supports RS-232C/RS-422/RS-485/TTL.
-
Product
Firmware for High-speed HDLC Mode
OP-FW10G
-
OP-FW10G is an expansion firmware to upgrade LE-3500 measuring Bit-Synch (HDLC/SDLC/X.25/CC-Link) and SPI communications up to 10Mbps. Hardware processing by FPGA built in the analyzer makes it possible to capture data with time stamp at micro second. It is useful to analyze SPI communications and High-speed HDLC communications such as RS-485 multi-drop CC-LINK and TTL signal level on the printed-circuit board.
-
Product
Portable Sequence Generator for Verification, Firmware & Validation
ISequenceSpec
-
The complexity of modern SoC has raised the requirement for HW/SW co-simulation to catch the bugs from the early design stage. There is lack of common set of sequences which can be shared across the teams. ISepenceSpec helps design teams to generate the unified test and programming sequences in UVM and Firmware from the specification. ISequenceSpec uses the register information from importing the standard formats like IP-XACT, SystemRDL, XML. User can define the test sequences in a simple editor, and then generate the unified test sequences from verification to validation.
-
Product
Software Defined Radio Firmware
FWSDR
-
The combination of the firmware FWSDR and the high-end digitizer ADQ14 creates a unique platform for software-defined radio. This 14-bit digitizer provides the high dynamic range needed in an RF environment and the interleaving technology provides high signal bandwidth coverage.The interleaving technology is provided through the use of SP Devices’ proprietary technology ADX which removes typical interleaving artifacts and enables the unique combination of bandwidth and dynamic range.
-
Product
Application-specific Motherboards With PCAN-MicroMod
PCAN MicroMod Digital 1 & 2
-
The motherboards for the PCAN-MicroMod provide an application-oriented environment. A wide supply voltage range and protective circuitry for the inputs and outputs are typical features of this product group. CANopen firmware is available for all PCAN-MicroMod motherboards.
-
Product
STP Engine (IP Core)
-
The Stream Transpose® (STP) engine is a reconfigurable processor (DRP: Dynamically Reconfigurable Processor) core that combines the flexibility of software and the speed of hardware. The firmware defining processing can be reconfigured in an instant, allowing an almost infinite variety of functions to be integrated into a system. A 40nm process is currently available for ASIC.
-
Product
Serial-to-Daq Minibox
Model 2367
-
* 2367 provides 32 digital I/O lines, 4 analog outputs, 6 analog inputs, 6 relay driver outputs and 4 temperature inputs.* Firmware supports ASCII command strings, Addressed commands for RS-485 networks and packet protocol. * Operates as a RS-232 as a RS-485 to Data Acquisition Module. * DB-25 connector has both RS-232 and RS-485 signals.* SCPI commands and IEEE 488.2 compatibility provide GPIB like operation over the serial link. * The 2367 is packaged in a CE approved Minibox™ metal case to minimize EMI/RFI. * 1 U high Rack Mounting Kit mountsone or two 4867s.* Plug-on Terminal Board simplifies wiring connections.* Includes Universal Power Adapter and 62-pin mating connector.
-
Product
Smart GPIB Serial Interface Board
Model 4806
-
* Provides GPIB-to-serial and serial-to-serial data paths for serial devices with RS-232 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message. • On board voltage regulator for operation from 5 to 15 Vdc power. • Rear panel mounting eliminates cables.
-
Product
Single Channel Instrument for General Acoustic / Vibration Measurements
SVAN 979
-
SVAN 979 is the most advanced and powerful single channel instrument for general acoustic and vibration measurements ever made. The list of the instrument outstanding features and functionalities includes:- high accuracy sound and vibration measurements- most powerful frequency analysis package- time-domain (WAV) and Audio Events recording to Micro SD card- very high dynamic measurement range- extremely flat frequency response (digitally compensated)- extremely flexible set of interfaces (USB, Bluetooth, IrDA, RS232 and more)- USB Host port providing very flexible functional extensions capabilities- firmware ready for GPRS and WLAN communication (USB Host port)- GPS time synchronisation
-
Product
SparkFun Dev Board
ESP8266 Thing
-
This is the SparkFun ESP8266 Thing Dev Board – a development board that has been solely designed around the ESP8266, with an integrated FTDI USB-to-Serial chip. The ESP8266 is a cost-effective, and very capable WiFi-enabled microcontroller. Like any microcontroller, it can be programmed to blink LEDs, trigger relays, monitor sensors, or automate coffee makers, and with an integrated WiFi controller, the ESP8266 is a one-stop shop for almost any Internet-connected project. To top it all off, the ESP8266 is incredibly easy-to-use: firmware can be developed in Arduino, and uploaded over a simple, serial interface. The ESP8266 Thing Development Board breaks out all of the module’s pins, and the USB-to-serial converter means you don’t need any peripheral components to program the chip. Just plug in a USB cable, download the Arduino board definitions, and start IoT-ing.
-
Product
Torque Measuring and Monitoring System
WISER 4000
-
TECAT Performance Systems, LLC
The WISER 4000 system is the latest release of TECAT’s low-cost, ultra-low power and extremely accurate torque sensor. The wireless system has the optional ability to measure 3-axis acceleration, barometric pressure and ambient temperature, all within the same incredibly small footprint. The 4000 includes on-board data logging without PC or DAQ connectivity, and remote flash capability, which enables firmware upgrades without removing the system from the unit under test. Featuring shunt calibration, TECAT’s latest WISER system is designed to simplify instrumentation verification for users, while allowing them to check calibration of the system in the field. In addition, the WISER 4000 has been enhanced with two additional outputs, a higher-speed recording, and is available with custom-built remote enclosures to protect the system’s remote unit and battery from damage due to debris.
-
Product
IVI Driver Package
IVI Development
-
The most complete IVI driver package from the most trusted name in IVI. Driver development can be tedious and distracting when you are scrambling to meet product deadlines. Researching the latest IVI standards, lack of driver documentation, and changing firmware all work against your product deadline. As a result, quality control over your product or driver or both can suffer. With IVI Development services from Pacific MindWorks you are free to focus on your product.
-
Product
Ethernet Tester
ProPlex IQ
-
Ethernet tester for entertainment production applications. Designed with input from production and staging professionals as an all-in-one device, it provides feedback and analysis on any Ethernet protocol, as well as network troubleshooting. It can act as a DMX cable tester, DMX receiver/transmitter, DMX timing analyzer, DMX recorder, RDM controller, or a bidirectional Ethernet-DMX gateway. It is also a PoE tester that can determine the capabilities of any connected PoE source. Finally, it can check SMPTE timecode or act as an LTC receiver/analyzer, and LTC transmitter, and users can use it to update Solaris/ProPlex firmware without a PC.
-
Product
Voltage Regulation & TransformerMonitoring
-
One of the essential features of the voltage regulators is the possibility to implement special functions via customer-specific programs without interfering with the firmware of the regulator. The programs can be created online using a simple editing tool. All necessary program elements, incl. help texts and sample program lines, are included with every regulator.
-
Product
Development Platform
NFC/WLC
-
CISC is offering various technology elements to support the design of NFC-based WLC (wireless charging). These pre-tested hardware modules including various antenna sizes, firmware, and software support customers to quickly have available solutions for their requirements. Customization helps in particular for very challenging application requirements. Customers benefit from very fast time to market for WLC solutions.
-
Product
Advanced Serial Protocol Analyzer
-
Most data networks are complicated, not just the hardware and network issues, but also the high-level protocols that devices use to communicate; and to make things even more complicated, many manufacturers have incorporated proprietary protocols for their devices. Integrating different devices and protocols within a data network is always the most challenging task for system integrators, firmware / software developers, and site engineers. From the simplest loopback test to complicated checksum calculation and sophisticated firmware and GUI software development, the 232Analyzer is designed to tackle all these challenges.
-
Product
Dual Port Simulator Fiber Channel PCI-X Module
PCI-X-FC4 Simulyzer
Simulator
The modules are available as a single-function board - for analysis or for simulation / data generation - but also as a full-function board for simultaneous analysis and simulation. By simply upgrading the firmware / software, a single function board can become a full function board without having to purchase new hardware.
-
Product
PCIe Gen 4 Switch Adapter
P411W-32P
-
The Broadcom P411W-32P is the industry’s first fully managed Gen 4.0 NVMe switch adapter, providing enterprise class options for NVMe solid state drive (SSD) attach requirements. The P411W-32P leverages Broadcom’s world-class board design, PEX88048 PCIe Gen 4.0 switch chip, and solid firmware expertise, to provide advanced features not available using traditional NVMe drive attach methods. Similar to Broadcom HBAs, the P411W-32P adapter is supplied with fully validated and supported firmware and standards based out of band manageability features.
-
Product
Wind Power Solution
NXA GAMESA
-
The NXA GAMESA is custom-made with firmware and fixtures designed specifically for Gamesa turbines: G80x, G90x, G114, G126, G132, G145. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
Product
DC Bias and RF Stimulus Control Module
Quantum SMART Fixture
-
Accel-RF Corporation, the world leader in turnkey RF automated reliability test instruments, has "unplugged" the industry-leading RF SMART Fixture from their automated test platform and made it available for benchtop test. The NEW Quantum SMART Fixture is a programmable self-contained DC bias and RF stimulus control module capable of synchronizing sequenced independent pulsed-bias and pulsed-RF signals to a DUT or remote fixture. The signals are controlled from a user interface compatible with Accel-RF's LIFETEST software. The Quantum SMART fixture is capable of "active" temperature control and monitoring of a remote DUT through embedded firmware in the microprocessor
-
Product
Broadband Test
458-3SLB
-
This compact, versatile unit accepts 1, 2 or 3 line modules or other products that use Telebyte's convenient line module form factor. At home in the lab or a high-volume production environment, it is capable of controlling from 1 - 24 channels and is ideal for testing DSL modems and other bandwidth-compliant telecom devices. While it can be used as a stand-alone unit, the built-in Control Module interfaces with a PC via RS-232, IEEE-488, or Ethernet. In addition, the 458 Universal GUI (included with purchase) may be used to control the unit from a PC. For added convenience, the Control Module firmware is field-upgradeable through the RS-232 port.
-
Product
LED Spectrometer
-
The New Feasa LED Spectrometer has been designed specifically to allow testing of LEDs on populated PCBs where access is limited. The Feasa LED Spectrometer includes customised on-board firmware for automatic colour calculation in multiple colour spaces. It uses a similar easy to use set of commands as the Feasa LED Analyser. When your quality demands Traceable Measurements the Feasa LED Spectrometer provide an ideal solution.
-
Product
27" Open Frame Gaming Monitor
GM-270G
Gaming Monitor
ADLINK’s GM-270G is a 27-inch open frame gaming monitor designed for casino gaming applications, especially for embedded slot machines or video lottery terminals. ADLINK offers highly flexible customization service, with customization options for cover glass, scaler board, and firmware.
-
Product
Distortion Detector PLUS
DD-1+
-
The purpose of this tool is to enable the installer to set the gain of an audio amplifier to match the source unit's output level, accurately and quickly. It can also be useful for detecting distortion in the audio signal caused by poorly designed or malfunctioning audio equipment. Sets audio system gain overlap, continuously variable from 0.0dB - 15.0dB in 0.1dB steps Checks gain overlap of an audio system without making any adjustments to the existing settings Verifies that the gain overlap of an install hasn't been tampered with after install Features our Patent Pending Distortion Detection system plus digital microcontroller and our proprietary firmware
-
Product
PNA-L Network Analyzers
-
The Keysight PNA-L network analyzers help you with your general-purpose network analysis needs. The PNA-L network analyzers give you efficiency and flexibility in both manufacturing and R&D applications. The PNA-L VNA covers various industries ranging from mobile telecommunications, wireless LAN component production, and aerospace and defense. The PNA-L network analyzers balance value and performance using the Keysight PNA network analyzer's core firmware.
-
Product
Electronic Compass - 3-axis Solid-State Magnetometer, 2-axis Electrolitic Tilt Sensor
Revolution
-
The Revolution electronic compass combines a precision 3-axis solid-state magnetometer and a rugged 2-axis electrolytic tilt sensor to provide accurate heading and tilt measurements over a broad range of environmental conditions. The firmware and signal processing algorithms have been refined and improved over three prior generations of electronic compasses to deliver the ultimate in performance from the available sensor data.
-
Product
Intelligent A/D I/O Unit
RAD242
-
Model RAD242 is an intelligent, two-differential-channel, 24-bit analog-input interface unit that includes a Delta-Sigma A/D converter. The converter has a digital output filter with adjustable notch frequency from 10 Hz to 2000 Hz. The pod also has 13 bits of digital input/output. A precision 10 VDC voltage that can be used for transducer excitation is available at connector pin 5. As much as 60 mA current can be provided. It is packaged in a NEMA 4 enclosure for remote installation in harsh environments. RAD242 also provides a user-definable interrupt input and counter/timer input. An optional RAD Firmware Development Kit is available if you wish to use those user-programmable input lines or to develop a custom program.
-
Product
Programmable Logic Unit PLUS
V2495
-
The V2495 can be controlled and programmed “on the fly” via the VME Bus or directly through the Mini-USB connector on the front panel. A Software tool is provided for free to easily upload the custom Firmware on the User FPGA.
