Firmware
-
Product
SparkFun ESP8266 Thing
Dev Board (with Headers)
-
This is the SparkFun ESP8266 Thing Dev Board --- a development board that has been solely designed around the ESP8266, with an integrated FTDI USB-to-Serial chip. The ESP8266 is a cost-effective and very capable WiFi-enabled microcontroller. Like any microcontroller, it can be programmed to blink LEDs, trigger relays, monitor sensors or automate coffee makers. With an integrated WiFi controller, the ESP8266 is a one-stop shop for almost any internet-connected project. To top it all off, the ESP8266 is incredibly easy to use; firmware can be developed in Arduino and uploaded over a simple serial interface. The ESP8266 Thing Development Board breaks out all of the module’s pins with pre-soldered headers, and the USB-to-serial converter means you don’t need any peripheral components to program the chip. Just plug in a USB cable, download the Arduino board definitions, and start IoT-ing.
-
Product
Application-specific Motherboards With PCAN-MicroMod
PCAN MicroMod Analog 1 & 2
-
The motherboards for the PCAN-MicroMod provide an application-oriented environment. A wide supply voltage range and protective circuitry for the inputs and outputs are typical features of this product group. CANopen firmware is available for all PCAN-MicroMod motherboards.
-
Product
GPIB To Serial Miniboxes™
-
ICS's GPIB to Serial Minibox™ Interfaces are fully enclosed for benchtop or rack mount applications. The GPIB to Serial Interfaces are available for transparent data transfer and with smart firmware to add an IEEE-488.2 interface to any serial device
-
Product
Standard Digitizer
725S Family
-
The 725S family is a digitizer capable of recording waveforms along with performing advanced algorithms for online digital pulse processing (DPP). Utilizing DPP Firmware, users can acquire quantitative physical parameters (Integrated Charge, Pulse Shape Discrimination with very fine time resolution, Pulse Height Analysis) as well as read out waveforms with automatic pulse identification and baseline suppression on channel basis (Zero-Length Encoding and Dynamic Acquisition Window). The wide range of DPP algorithms supported by the 725S make it a “must-have” for any type of nuclear physics application.
-
Product
Scale / Weight Meter
-
Equipped with a DC or load cell signal conditioner, this Laureate offers special firmware for scale / weighing applications: two tare functions; count by 1, 2, 5, 10, 20, 50 or 100; auto-zero function; setpoint offset, and dummy right-hand zero for display to 999,990. Built-in excitation for up to four 350-ohm load cells in parallel.
-
Product
Free Modbus Device Tester Software
-
Global Multimedia Private Ltd.
This software was developed to test Information Displays made by Global Multimedia for modbus protocol compliance. It can be used to test your firmware on a serial device for Modbus RTU conformance.
-
Product
Distortion Detector PLUS
DD-1+
-
The purpose of this tool is to enable the installer to set the gain of an audio amplifier to match the source unit's output level, accurately and quickly. It can also be useful for detecting distortion in the audio signal caused by poorly designed or malfunctioning audio equipment. Sets audio system gain overlap, continuously variable from 0.0dB - 15.0dB in 0.1dB steps Checks gain overlap of an audio system without making any adjustments to the existing settings Verifies that the gain overlap of an install hasn't been tampered with after install Features our Patent Pending Distortion Detection system plus digital microcontroller and our proprietary firmware
-
Product
Master Controller
RatMaster
-
- Jumper free configuration- Intuitive configuration software- RS-232, TTL and CI-V interfaces- Automatically generates Icom CI-V data stream from non-Icom radios- Configurable band limits- Built-in USB interface- Set default antenna per band- Field upgradeable firmware- Anodized aluminum case- Laser engraved panels
-
Product
Network Analyzer N-Port Calibrated Measurements
S95551B
Network Analyzer
PXI vector network analyzers (VNA) offer the capability to extend the number of ports for your measurements by using additional modules. When multiple modules are used, they are configured for multiport operation. The S95551B adds a multiport analyzer mode that enables full multiport error correction and measurement capabilities. The instruments may be identified as one VNA by the firmware running on an external host PC. At least one VNA instrument connected to your PC must have one S95551B license to maintain N-port capabilities.
-
Product
ANSI X3.28 Interface Board
Model 4804B-7
-
* F30145 firmware converts printable ASCII character strings into the ANSI X3.28 serial protocol.* User selectable single-ended RS-232 and differential RS-422/RS-485 serial signals.* Can be used to replace obsolete ICS 4814 Interfaces.* Connect to the rear panel with a GPIB Flat-ribbon cable or with a GPIB Connector/Address Switch Cable.* Runs on 5 Vdc regulated or 5.5 to 15 V unregulated power.
-
Product
Digitizers
-
CAEN has developed a complete family of digitizers that consists of several models differing in sampling frequency, resolution, form factor (VME, NIM, Desktop, Rack) and other features.In recent years CAEN opened the doors of its R&D to the Open FPGA technology, which is becoming more and more widely used and required. In addition, we decided to invest many resources in order to make this technology accessible to everyone. These efforts result in innovative Programmable Digitizer families and the SCI-Compiler software for easy-programming of the Open FPGA simplifying firmware writing with a block-based visual programming language.
-
Product
Dielectric Material Test Fixture
16453A
Test Fixture
The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.
-
Product
Software
-
A tool is available to update ARGUS testers, which is also included in our WINplus and WINanalyse software packages. With this tool, the latest firmware versions can be downloaded to the tester from www.argus.info. The whole procedure is very simple and intuitive, thanks to the integrated step-by-step instructions.
-
Product
VME Sequencer PCI Express to VME Interface
SIS3104-2
-
The SIS3104-2 is the Artix-7 based successor to the SIS3104 board. It is backward compatible to the SIS3100/SIS3104 standard models and can be used as a drop in replacement. With two Gigabit/s link firmware transfer rates in excess of 160 MByte/s are possible im combination with the SIS1100-e2 single lane PCI Express card.
-
Product
Serial-to-Daq Card
Model 2307
-
* 2307 Board provides 32 digital I/O lines, 4 analog outputs, 6 analog inputs, 6 relay driver outputs and 4 temperature inputs.* Firmware supports ASCII command strings, Addressed commands for RS-485 networks and packet protocol. * Operates as a RS-232 as a RS-485 to Data Acquisition Board. * DE-9 connector has both RS-232 and RS-485 signals.* SCPI commands and IEEE 488.2 compatibility provide GPIB like operation over the serial link. * Runs on 5 Vdc power.
-
Product
Test RTM with Ethernet SFP
VR300
-
Sundance Multiprocessor Technology Ltd.
The VR300 is a Test RTM, typically used during firmware and software development and debugging cycles on the VF360. The rear panel contains two mini-USB connectors, a Dual mini-SAS (SFF-8088) connector and a SFP case.
-
Product
Modbus TCP Gateway
SI-485MB
-
SI-485MB is a Modbus gateway to convert bi-directionally Modbus RTU/ASCII of serial interface to Modebus TCP of Ethernet. The firmware for gateway process supports Modbus TCP master mode and Modbu TCP slave mode and supports all the current ModbusRTU/ASCII register and command conversion. The robust metal body, broad range of temperature, wide input voltage range, and the support for installation by options such as 35mm DIN rail and wall bracket allow you to use it for factory automation without worry.
-
Product
Advanced Serial Protocol Analyzer
-
Most data networks are complicated, not just the hardware and network issues, but also the high-level protocols that devices use to communicate; and to make things even more complicated, many manufacturers have incorporated proprietary protocols for their devices. Integrating different devices and protocols within a data network is always the most challenging task for system integrators, firmware / software developers, and site engineers. From the simplest loopback test to complicated checksum calculation and sophisticated firmware and GUI software development, the 232Analyzer is designed to tackle all these challenges.
-
Product
Dual Port Simulator Fiber Channel PXIe Module
PXIe-FC4 Simulyzer
Simulator
The modules are available as a single-function board - for analysis or for simulation / data generation - but also as a full-function board for simultaneous analysis and simulation. By simply upgrading the firmware / software, a single function board can become a full function board without having to purchase new hardware.
-
Product
Warm-Up Board
WECO 9000
-
The WECO 9000 Warm-Up Board from Radian Research provides a safe, easy to use, affordable solution to your AMI meter functional testing. The WECO 9000 originated as part of RADIAN Innovate™ Custom Design Solutions. Numerous process improvement workshops RADIAN facilitated at electric utilities have shown us that meter shops are experiencing as low as 65% pass yield on AMI meter testing. This means almost half the meters arriving are transported through the testing process and not ready for accuracy testing. Typical failures include inoperable display, diagnostic errors, disconnect switch in an open state, wrong firmware version, and inability to register on the communications network.
-
Product
Intelligent A/D I/O Unit
RAD242
-
Model RAD242 is an intelligent, two-differential-channel, 24-bit analog-input interface unit that includes a Delta-Sigma A/D converter. The converter has a digital output filter with adjustable notch frequency from 10 Hz to 2000 Hz. The pod also has 13 bits of digital input/output. A precision 10 VDC voltage that can be used for transducer excitation is available at connector pin 5. As much as 60 mA current can be provided. It is packaged in a NEMA 4 enclosure for remote installation in harsh environments. RAD242 also provides a user-definable interrupt input and counter/timer input. An optional RAD Firmware Development Kit is available if you wish to use those user-programmable input lines or to develop a custom program.
-
Product
Next Generation Subsea Inertial Navigation Systems
TOGSINS
-
The new TOGSINS builds on core TSS fibre optic gyro technology by incorporating inertial navigation (INS) capability. As with TOGS, it is available in three standard heading accuracy variants: 0.1° (TOGSINS1), 0.3° (TOGSINS3) and 0.5° (TOGSINS5), all rated for operational depths to 4,000m or 6,000m giving you a range for all your needs.Inertial position data is produced using an INS algorithm, within the firmware framework of TOGS, whilst attitude data is delivered via accurate roll/pitch measurement of 0.01° (TOGSINS1) and 0.05° (TOGSINS3 and TOGSINS5), and a heave performance of 5cm or 5%.
-
Product
Wind Power Solution
ECO MITSUBISHI
-
The ECO MITSUBISHI is custom-made with firmware and fixtures designed specifically for Mitsubishi turbines: 1000, 1000A, MWT 2.4. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
Product
Broadband Test
458-3SLB
-
This compact, versatile unit accepts 1, 2 or 3 line modules or other products that use Telebyte's convenient line module form factor. At home in the lab or a high-volume production environment, it is capable of controlling from 1 - 24 channels and is ideal for testing DSL modems and other bandwidth-compliant telecom devices. While it can be used as a stand-alone unit, the built-in Control Module interfaces with a PC via RS-232, IEEE-488, or Ethernet. In addition, the 458 Universal GUI (included with purchase) may be used to control the unit from a PC. For added convenience, the Control Module firmware is field-upgradeable through the RS-232 port.
-
Product
USB Connectivity Bridges
USBXpress
-
Silicon Labs USBXpress devices are highly optimized solutions that enable designers to easily add USB to existing and new applications. These fixed function devices provide the easiest method to add USB without the need for any firmware or driver development. USBxpress portfolio supports several USB to serial bridge devices including human interface (HID) devices and USB Audio devices.
-
Product
M2T Transmitter
-
The M2T half-rack transmitter houses two stereo transmitters to provide two stereo audio channels, and for up to four mono audio channels in a single rack space. The audio inputs can be individually configured to be analog or Dante compatible. The analog input connectors are full-size XLR/TRS combo types for balanced line-level analog signals while the input preamp circuits use a special balanced amplifier with very high common mode rejection to minimize hum and noise. A Dante™ Ultimo™ interface via dual RJ45 connectors accepts Dante networked audio inputs and can daisy chain the digital stream to additional units via CAT6 cables. An additional RJ45 jack provides an Ethernet connection for programming and control via Wireless Designer™ software and a USB jack on the front panel allows for firmware updates. The transmitter features a full color, backlit LCD for high visibility in any environment, while the chassis is all-metal and can be racked singly or in pairs using included rack mount hardware.
-
Product
STP Engine (IP Core)
-
The Stream Transpose® (STP) engine is a reconfigurable processor (DRP: Dynamically Reconfigurable Processor) core that combines the flexibility of software and the speed of hardware. The firmware defining processing can be reconfigured in an instant, allowing an almost infinite variety of functions to be integrated into a system. A 40nm process is currently available for ASIC.
-
Product
Dual 2.0 Gsps. 12 Bit ADC FMC
ADF-D2000
-
This FPGA Mezzanine Card (FMC) converts two channels of up to 2.8GHz analog input bandwidth at 1.0, 1.6, 1.8, or 2.0 Gsps and 12-bit resolution. Additionally, this FMC can be used in an interleaved mode to convert a single channel at 2.0, 3.2, 3.6, or 4.0 Gsps and 12-bit resolution. Based on the VITA 57 specification, the ADF-D1600 enables direct coupling of unparalleled analog-digital conversion capability with the VME/VXS/AMC/VPX/PCI-E carrier board of your choice. DEG engineers have designed this product and associated HDL firmware to work with both Altera and AMD FPGAs.
-
Product
Nitrous Oxide Gas Sensors
-
The PST Dynament nitrous oxide (N2O) Platinum sensors are designed with patented non-dispersive infrared technology and contain all the necessary optics, electronics and firmware to provide a linearized, temperature-compensated output.
-
Product
DAQ Modules
Q.series X DAQ Modules for EtherCAT
-
All Q.series X DAQ systems possess the same measurement capabilities and performance. The main differentiating factor between the XL and XE versions of Q.series X is the Fieldbus communication protocol, which can be interchanged on Q.series X modules using a simple firmware update.
