SIR Testing
testing check's PCB for shorts or current leakage between conductors.
-
Product
Radar Test System
UTP 5065
Test System
Radar sensors are core elements to realize autonomous driving. The UTP 5065 radar test system from NOFFZ Technologies has a compact vertical design and contains everything needed to allow State-of-the-Art measurement and sensor calibration. The test bench setup and component selection are tuned to get best possible results for highly accurate and cost-efficient testing in production of automotive radar sensors.
-
Product
In-line High-Density ICT System Series 7i
E9988GL
In-Circuit Test System
The E9988GL Keysight i3070 Series 7i Inline High-Density In-Circuit Test (ICT) system brings industry-leading ICT technologies into your automated manufacturing line, saving resources and optimizing your automated test strategy.
-
Product
Memory Test System
T5801
Test System
Capable of Testing Ultra-High-Speed DRAM Devices, Supporting Next-Generation GDDR7, LPDDR6, and DDR6 Technologies
-
Product
110 GHz, 1.0 Mm (m-f) Test Port Cable 10 Cm
11500JK10
Test Port Cable
Connect test ports to devices, fixtures, or probe tips with this 10-cm cable
-
Product
Test Platforms
Test Platform
Leverage 20+ Years of Test Industry Experience with Built-In IP for Maximum Reuse
-
Product
Electronic Control Unit Functional Test
Functional Test
End-of-line tests are critical to ensure passenger safety in the era of smarter vehicles. A flexible test solution is needed to ensure extensive test coverage and high test throughput with a low total cost of ownership.
-
Product
Advanced SoC/Analog Test System
3650
Test System
Chroma 3650 is an SoC tester with high throughput and high parallel test capabilities to provide the most cost-effective solution for fabless, IDM and testing houses.
-
Product
Bottom Electrode SMD Test Fixture
16197A
Test Fixture
The 16197A is designed for impedance evaluations of bottom electrode SMDs. It achieves stable frequency characteristics up to 3 GHz and provides highly repeatable measurements. The Keysight 16197A supports various SMD sizes, as small as 1005 (mm)/0402 (inch) and as large as 3225 (mm)/1210 (inch). Accommodation of the 0603 (mm)/0201 (inch) size is available with option 001.
-
Product
ARINC-429 Module
M4K429RTx
Test Module
The M4K429RTx is an ARINC-429 multi-channel test and simulation module to be used on the Excalibur 4000 family of carrier boards. The module supports up to ten ARINC-429 channels in any combination of transmitters and receivers. Each of these channels feature error injection and detection capabilities. The receive channels allow for the storage of all selected Labels with status and time tag information appended to each word.
-
Product
Photodiode Burn-in Reliability Test System
58606
Test System
The Chroma 58606 PD/APD Burn-in system is a high density, multifunction and temperature controlled module based system for photo diode burn-in and lifetime test. Each module has up to 256 Source Measurement Unit channels which can source current and measure voltage in various scenarios such as one described below. The system can accommodate 7 modules for a total of 1,792 device channels.
-
Product
Compact EMS/EMI Test Platform
CEMS100
Test Platform
Setting up an EMS/EMI test system is a very complex process requiring significant investment. The steps involved include custom planning, design, installation and configuration of various components and standalone instruments as well as the RF shielded anechoic chamber. Rohde & Schwarz offers the standardized R&S®CEMS100 test platform that is the company's first flexible, reliable and cost-effective off-the-shelf solution for radiated EMS measurements in line with IEC/EN 61000-4-3.
-
Product
EVSE Test Platform
Test Platform
To manage both the challenging high-power requirements of electric vehicle supply equipment and the market demand, it is crucial to rely on a test system that performs to your specs. The right system needs to combine the tools for reliable asset communication, microgrid management, effective protocol simulation and high-power testing. This EVSE platform combines the right energy regeneration equipment with 25+ years of test experience to deliver the results you need to meet conformance in the time you need it.
-
Product
Drive Controller Function Test – Universal Functional Test System for Industrial Electronics
Functional Test
General functional test system based on LXI instrumentation for high mix / low to medium volume manufacturing. DUTs are tested which are mainly used as communication and measurement modules in power plant technology, grid management and electrical drives.
-
Product
Flexible Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131E
test
Achieve phase stability with this 96.5-cm cable when a DUT is connected, with adapter, directly to the test set port
-
Product
Flash Memory Test System
T5830
Test System
T5830 memory tester, the latest member of its T5800 product family, optimized for testing a wide range of flash memory devices used in mobile electronic devices. The highly flexible T5830 tester has all of the capabilities needed to perform wafer sorting and final testing of price-sensitive flash memories.
-
Product
VITA 62, 3U Test Fixture
TF-3U-7B041-1
Test Fixture
This Power Supply test fixture is being proposed as a tool for checking Injector / Ejector operation, proper alignment of the VITA 62 connector and proper alignment of both keys on a Single slot, 3U, VITA 62/SOSA power supply.
-
Product
Scienlab Battery Test System - Cell Level
SL1007A
Test System
The SL1007A Scienlab Battery Test System – Cell Level enables you to accurately and productively test battery cells for automotive and industrial applications. The bidirectional power supply charges and discharges your cells under test with very high efficiency.
-
Product
Medalist i1000D
U9401B
In-Circuit Test System
The Keysight Medalist i1000D is now even better. Improving from its previous state of an analog-only ICT, the new digital release of the system now features per pin programmable digital cards and a whole new set of intuitive software graphical user interfaces (GUIs) that makes programming and development effortless.
-
Product
PXI Semiconductor/IC Test System
Test System
A high-density 100MHz PXIe digital IO card designed for characterizing, validating, and testing a variety of digital and mixed-signal ICs. Each IO card consists of a Sequencer Pattern Generator (SQPG) and 32 channels of full ATE-like features. The 33010 IO card is expandable up to 256 channels. Some unique features of the 33010 include an on-board SQPG, per pin timing/levels/ PMU/TFMU, multiple time domains, and multithreaded testing for complex IC testing. Each channel is also equipped with 64M vector memory, 16 timing sets with on-the-fly timing change, and per pin timing and frequency measurements up to 400 MHz.
-
Product
Fully-Automated CTIA-Compliant OTA Test System
TS8991
Test System
The R&S®TS8991 OTA performance test system measures the spatial radiation and sensitivity characteristic as specified by CTIA and 3GPP.The system software provides ready-to-use test templates for OTA measurements and supports all wireless standards.The integrated report function collects all measured test data such as graphics or numeric results, test environments, EUT information and hardware setup in one document.
-
Product
NI Vehicle Radar Test System
Test System
VRTS provides automated radar measurement and obstacle simulation capabilities for 76 to 81 GHz automotive radar systems. With VRTS, you can perform precision RF measurements and simulate a wide range of test scenarios for radar hardware and software subsystems, including sensors, advanced driver assistance systems (ADAS), and embedded software. Use VRTS for all phases, from design to manufacturing, of ADAS and radar system test.
-
Product
Single Site Test Handler
3210
Test Handler
Chroma Single Site Test Handler 3210 supports various package types such as BGA series, QFP series, QFN, TSOP, and more. The handler is primarily designed for early device design and engineering validation.
-
Product
Liquid Test Fixture
16452A
Test Fixture
The 16452A provides accurate dielectric constant and impedance measurements of liquid materials. The 16452A employs the parallel plate method, which sandwiches the liquid material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixure.
-
Product
Verification And Diagnostic Tools
Y1131A
Test Fixture
Provides module-specific tests to troubleshoot relay failures and predict maintenance requirements.
-
Product
PCB Test System
Circuit Wizard - CW409
Test System
Qmax Test Technologies Pvt. Ltd.
CW 409 –Circuit Wizard PCB Test System has all the features of QT9627 such as Desktop PCB Test System. It can be configured to maximum 64 Channels of In-circuit Functional Test Channels and 64 Channels of QSM V-I Signature Test.Maximum Digital Test Speed 10MHz in the QT9627 .It can be connected to any PC/AT or Laptop with Windows 10 operating system through USB Plug and play interface. It operates on user friendly Qmax Test Director software platform with different modes like Test Station for operator level use Test Sequencer mode for Programmer level use and Interactive Workstation mode for quick working.
-
Product
Inline test system for FCT, ICT, ISP and Boundary Scan for Automated Operation
LEON InLine
Test System
High production volume often requires inline solutions with fully automated product Handling – the LEONlnline is a complete Inline Board Test Solutions for printed circuit boards. It integrates a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors.
-
Product
Display Driver Test System
T6391
Test System
High-resolution flat-panel displays (LCDs / OLEDs) are becoming increasingly integrated. It is common for today's display driver ICs (DDIs) to contain a multitude of logic/analog circuits to manage advanced operations including touch-sensor functions. At the same time, the rapidly growing applications of LCDs / OLEDs in mobile electronics are driving demand for DDI's with smaller sizes and greater capabilities. These factors present serious IC-testing challenges. ADVANTEST's T6391 system is designed to address these needs along with DDIs' increasing number of pins and faster interfaces.
-
Product
Memory Test System
T5833/T5833ES
Test System
T5833 system is a cost-efficient, high-volume test solution capable of performing both wafer sort and final test of DRAM and NAND flash memory devices. Amid surging sales of mobile electronics, DRAMs, NAND flash memories and multi-chip packages (MCPs) — the main device types used in smart phones and tablets — are quickly evolving toward higher speeds and greater device capacity. Internet and cloud servers also are driving demand for faster, higher-capacity ICs. Yet the cost of testing today's wide array of memory devices is an obstacle for chipmakers, which urgently require solutions that can deliver high functionality, high performance and low cost of test (COT). Advantest's new, multifunctional T5833 memory test system meets these needs, delivering both wafer sort and final test capabilities for a full range of memory devices, including LPDDR3-DRAMs, high-speed NAND flash memories and next-generation non-volatile memory ICs.
-
Product
Noise Figure Analysis Using NI PXI RF Test Instruments
NI-RFmx Noise Figure
Test Instrument
Measure noise figure, gain, Y-factor, effective temperatures, hot and cold power, and moreOptimized calibration and measurement routines for multi-DUT test using Y-factor and cold sourceSupports the PXIe-5668R 26.5 GHz VSA, the PXIe-5698 26.5 GHz preamplifier, and VSTsDesigned for use with industry-standard noise sources such as the Noisecom NC346 Series
-
Product
At-Speed Non-Intrusive Functional Testing
ScanExpress JET
Functional Test
Functional circuit board testing presents many challenges that are often costly and time consuming. Most functional tests need to be customized for each design, limiting reusability. This results in software engineers vying for time between development code and test code. Even when functional tests become available, the diagnostic details are often inadequate to give clear visibility on a given problem.ScanExpress JET is a tool designed to overcome these challenges by automating the functional test generation process on CPU–based IEEE-1149.1 compliant circuit boards. Coined JTAG Embedded Test, JET is the preferred method for at-speed, non-intrusive functional testing.
