Modulation
the varying of amplitude, frequency, or phase.
See Also: Optical Modulation, Modulation Analysis, Modulation Analyzers, Modulation Meters, MER
-
Product
Gigabit Ethernet XMC module
IC-GIGA-XMCb
-
The IC-GIGA-XMCb is an XMC module providing up to four 10/100/1000 Ethernet channels.
-
Product
Electric Vehicle Battery Cell Tester
MCV
-
The MCV is a low-current life cycle test system for development of primary and rechargeable batteries in various chemistries. Operating from a common microprocessor, multiple circuits in the MCV module can run individual test programs. Additionally, the MCV is designed and built for ease of maintenance and service. The modular construction means that most subassemblies, large or small, remove easily for service outside the cabinet and fast replacement.
-
Product
Input / Output Modules
-
*Competitive cost-per-channel*24-bit A/D converters; 16-bit exported*ICP, Strain Gauge, Frequency, String Pot, Thermocouple*Portable, rugged, stand-alone operation*Open-source command set for third-party software applications
-
Product
Network Interface Card
NIC10GFT
Interface Card
The NIC10GFT is a dual port 10GBase-T XMC module that brings 10GbE expandability to new and existing embedded systems with available XMC slots.
-
Product
PXI Precision Resistor Module 6-Channel, 3Ohm to 22.3M
40-297-054
Programmable Resistor Module
A simple solution for applications requiring accurate simulation of resistive sensors. The series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI 4-Slot BRIC Matrix, 30x32 1-Pole (6 Sub-cards)
40-562B-021-30X32
Matrix Switch Module
The 40-562B-021-30X32 is a high density BRIC4 matrix module with a size of 30x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
Multi-Channel Synchronization Module for M8195A
M8197A
Module
Synchronization Module for up to 4x M8195A Arbitrary Waveform Generator units.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-312-HI
Programmable Resistor Module
The 40-230-312-HI (PXI) and 42-230-312-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 122Ω with 0.5Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI 4 Slot BRIC 150x4 2A 1-Pole Matrix
40-568-102
Matrix Switch Module
The 40-568 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 200VDC/140VAC. The 40-568 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI 2-Slot BRIC Matrix, 15x32 1-Pole (3 Sub-cards)
40-562B-221-15X32
Matrix Switch Module
The 40-562B-221-10X32 is a high density BRIC2 matrix module with a size of 10x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 2 Amp Multiplexer, 8-Bank, 8-Channel, 1-Pole
40-657A-001-8/8/1
Multiplexer Module
The 40-657A-001-8/8/1 is a 8-bank, 8-channel, 1-pole MUX and is part of our range of High Density 2 Amp Power Multiplexer Modules available in a choice of configurations, containing up to 8 separate multiplexers, all 1-pole switching. They are suitable for switching signals to 110VDC/250VAC at 2Amps, 90W.
-
Product
PXI-6115, 4 AI (12-Bit, 10 MS/s/ch), Buffer Size 16MS, 2 AO, 8 DIO, PXI Multifunction I/O Module
778194-01
Multifunction I/O
4 AI (12-Bit, 10 MS/s/ch), 2 AO, 8 DIO, PXI Multifunction I/O Module - The PXI‑6115 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 24‑bit counters, and digital triggering. It is ideal for a variety of applications, such as stimulus/response applications where synchronization among analog input, analog output, and digital I/O is required, 42 V automotive applications, radar, sonar, and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PXIe-4135, PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit
783762-02
Source Measure Unit
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit - The PXIe-4135 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology and native triaxial connectors help you perform high-precision measurements with a current resolution of 10 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4135 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
Product
3U OpenVPX FMC Carrier
VF360
-
Sundance Multiprocessor Technology Ltd.
The VF360 is a 3U OpenVPX module that leverages on Altera Stratix® V FPGA and Texas Instruments KeyStone Multicore DSP technology to provide an ultra-high bandwidth processing platform, ideally suited for computation and bandwidth intensive applications such as Radar, Networking, SIGINT, EW, SDR and Video.
-
Product
2MP Sony STARVIS® IMX290 Ultra-Lowlight Camera Module
e-CAM21_CUMI290_MOD
-
The e-CAM21_CUMI290_MOD is a 2 MP ultra-lowlight RAW MIPI camera module with the S-mount (M12) lens holder. This FHD camera module is based on SONY IMX290, one of the most popular Sony's STARVIS® CMOS sensor. SONY IMX290 is a 1/2.8" rolling shutter CMOS sensor with 2.9µm pixel size. Its effective pixel back-illuminated technology with improved sensitivity in the visible-light and near infrared light enables customers to capture images even in absolute darkness. The e-CAM21_CUMI290_MOD can stream uncompressed FHD @120 fps in 10-bit mode and 60fps in 12-bit mode.
-
Product
Peripheral Boards
-
Advantech CPCI solution includes GPU, Ethernet, storage blades, and AC/DC power modules that comply with industry standards for broad compatibility.
-
Product
PXI/PXIe RF Multiplexer, Quad 4-Channel, Terminated Common, 3GHz, 50Ω, MCX
42-876A-104
Multiplexer Module
The 40-876A-104 (PXI) and 42-876A-104 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 4 banks in a single slot. Additionally, extra switching allows the common connection to be terminated into 50 Ohm, maintaining signal integrity. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
PXI 8 Slot BRIC 176x4 2-Pole (4 sub-cards)
40-562A-122-176X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
GCxGC Time-of-Flight Mass Spectrometer
PEGASUS® BT 4D
-
The Pegasus BT 4D offers enhanced sensitivity by coupling our benchtop Pegasus BT with our high performance GCxGC thermal modulation system. This combination gives the Pegasus BT 4D the ability to interrogate challenging samples where the best sensitivity is needed. Unique and powerful software and hardware features simplify quantitation, while also dramatically making GCxGC easy to use and understand.
-
Product
3U CPCI I/O & Comm Board
3U cPCI 75C5
Multifunction I/O
NAI’s 75C5 is a 3U cPCI Multifunction I/O and Communication Board with three independent function module slots. Two of the slots can be configured with a variety of I/O and communication functions; the third, with either a combination module featuring four multiplexed Analog-to-Digital (A/D) channels and 28 Discrete I/O programmable channels, or with a reference power supply. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
PXI 4 Slot BRIC 138x8 1-Pole (3 sub-cards)
40-560A-021-138X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI Versatile Multiplexer, Solid State, 125mA, 100V
40-683A-001
Multiplexer Module
The 40-683A-001 is a very high-density versatile PXI Multiplexer module featuring a wide range of selectable switching configurations with 125mA current and 100V voltage handling. The 40-683A is especially useful where a high-density MUX array is required that can adapt to different test configurations for different test targets, or where a test system may have to be reconfigured in the future.
-
Product
Logic Analyzer Probe
FS2520
-
The FS2520 is our newest and fastest logic analyzer probe used to test DDR4 DIMM memory. It is designed to work exclusively with 3 Keysight U4164A logic analysis modules operating in either Quad Sample State or Quarter Channel 10GHz timing modes. This gives the user an extremely effective tool for debugging, testing and verifying DDR4 DIMMs running above 4000MT/s. It’s like having a 100 channel scope.
-
Product
IndustryPack modules
PC104pIP
-
If you want to use IndustryPack modules with your PC/104+ system then the PC104pIP is the choice for you. The PC104pIP combines features you need with simplicity and speed. One IP module can be installed per carrier. Multiple carriers can be used in a stack. The PC104pIP is highly integrated with the PCI and IP interfaces closely coupled within the same FPGA
-
Product
NI-9226, 8-Channel, 400 S/s Aggregate, 0 Ω to 4000 Ω, PT1000 RTD C Series Temperature Input Module
783864-01
Temperature Input Module
8-Channel, 400 S/s Aggregate, 0 Ω to 4000 Ω, PT1000 RTD C Series Temperature Input Module - The NI‑9226 is a resistance temperature detector (RTD) input module. You can configure the NI‑9226 for two sample rate modes: high sample rate or high resolution. The NI‑9226 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3‑ or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per-channel current excitation. The NI‑9226 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
Product
Control Module
MOC
-
The MOC is our universal control module for a wide variety of tasks, such as controlling relays in the fixture.
-
Product
Virtex-5 FPGA with Plug-in I/O
PMC-VSX
-
Acromag’s PMC-VSX boards feature a reconfigurable Xilinx® Virtex™-5 FPGA enhanced with multiple high-speed memory buffers and a high-throughput PCI-X interface. Field I/O interfaces to the FPGA via the rear J4/P4 connector and/or with optional front mezzanine plug-in I/O modules. The result is a powerful and flexible I/O processor module that is capable of executing your custom instruction sets and algorithms.
-
Product
NI-9220, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 16-Channel C Series Voltage Input Modul
782615-01
-
±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 16-Channel C Series Voltage Input Module - The NI‑9220 performs simultaneous differential analog inputs with 250 Vrms CAT II or 60 VDC CAT I isolation. The module is capable of generating 3.2 MB/s of data at … the maximum sampling rate. There are two connector options for the NI‑9220: a 36-position spring-terminal connector and a 37‑position D‑SUB connector.
-
Product
TB-2635, Screw Terminal, 8x16, 2-Wire PXI Module Matrix Terminal Block
778839-01
Terminal Block
Screw Terminal, 8x16, 2-Wire PXI Module Matrix Terminal Block - The TB-2635 provides the necessary routing to configure the PXI-2529 PXI Matrix Switch Module as a 2-wire 8×16 matrix. You can directly connect the TB-2635 to the front panel I/O connectors of the PXI-2529. The TB-2635 includes screw terminals that provide access to the rows and columns of the matrix.
-
Product
Specialized Extender Card Testing IP Modules
IP-Debug-Bus
-
IP-Debug-Bus is a specialized extender card which is optimized for testing IP Modules. The bus signals are all accessible via test points. The testpoints include multiple ground locations and .025 sq. posts for ease of connection to your logic analyzer or scope. The testpoints are labeled for easy identification
