-
product
LED Test
Universal LightProbe Penta sensors are Optomistic Products' most popular LED test sensor, relied upon for their versatility in accommodating most LED test applications for color and intensity. The Penta Sensor provides analog voltage outputs, and features built-in color binning, eliminating the need to convert LED wavelength to visual color in the ATE software, and saving valuable processing time. For use with any of the Universal LightProbe Fiber-Optic Probes.
-
product
PXI 1A Fault Insertion Switch 22-Channel
40-195-001
The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Relays ...show more -
product
High Speed Camera Systems
HotShot e1024
The HotShot e1024 is perfect for a multitude of high speed applications including: human / veterinary biomechanics analysis, research, design & test, production and manufacturing, to name a few.
-
product
Automotive Ethernet Rx Compliance Software
AE6910R
Unlike CAN, LIN, or MOST, the IEEE standard for automotive Ethernet demands rigorous compliance verification using specific test cases. The test requirements include complex measurements: vector network analysis with S-parameters, bit error rate (BER) test, and protocol analysis of high-speed digital signals.
-
product
PXI 5W Programmable Resistor Module, 1-Channel, 3Ω to 22.3MΩ
40-252-054
The 40-252-054 is a programmable resistor module with 1 channel which can be set between 3Ω and 22.3MΩ with 2Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Environmental Meter
Shenzhen UYIGAO Electronic Technology Co., Ltd
The meter can test Sound Level and Temperature.
-
product
Electrostatic Discharge Test
The electrostatic discharge test is designed to determine the ability of equipment to perform its intended function without permanent degradation of performance as a result of an air discharged electrostatic pulse. Electrostatic discharge is the result of an unbalanced electrical charge. Typically, it is created by insulator surfaces rubbing together or pulling apart. A transfer of electrostatic charge between bodies (materials, components, etc.) at different electrostatic potentials is caused by direct contact.
-
product
AC Load Banks
K-1000 Series
Kongter Test & Measurement Co., Limited
Load bank testing is vital to replicate and verify the operation of critical backup power systems such as diesel generators and uninterruptible power supplies (UPS). Kongter offers a wide range of customer-tailored AC load banks that excel in a range of load test applications and environments.
-
product
Multi Channel Vibration Motor Aging Tester
BK2022
The BK2022 is the ultimate in aging testing for coin type vibration motors. You can connect up to 128 motors and the system will automatically test them all at the same time. It tests RPM, current, individual errors, and even total error and puts the information on the monitor in real time. You can store the results and retrieve them later to be analyzed so you can keep track of the accuracy and stability of your manufacturing process. In addition, BaKo’s BS1123-BS2022 program will be modified to fit your needs so that the testing you do is a custom fit.
-
product
Current Integrated Sources
CIS
The CIS current integrated source was designed to provide a stable alternating current source for the electricity meter test equipment, and in laboratories. The output current is isolated and independent from the mains voltage. Different CIS versions are available depending upon the values of output power and output current required.
-
product
Eggplant Test Automation
Keysight Eggplant Test 7.0: Test automation software designed to streamline testing and reduce associated risks with manual do-it-yourself testing on any platform.
-
product
PXIe-6571, 1-Slot, 100 MVector/s PXI Digital Pattern Instrument
786320-01
1-Slot, 100 MVector/s PXI Digital Pattern Instrument - The PXIe‑6571 is designed for semiconductor characterization and production test. It includes the Digital Pattern Editor for configuring pin maps, specifications, levels, timing, and patterns. It also includes debugging tools … like Shmoo, digital scope, and viewers for history RAM, pin states, and system status. The PXIe-6571 requires a chassis with 82 W slot cooling capacity, such as the PXIe-1095.
-
product
Environmental Test Probe, Temperature
72-8366
Simple thermocouple junction at the end of a 1m wire provides effective low cost ambient temperature measurement. It is suitable for measuring air temperature and may be placed in direct contact with hard surfaces. Type K thermocouple temperature probes are commonly used with all types of industrial temperature controls and measurement equipment, and are compatible with Tenma handheld thermometers and digital multimeters that include temperature function. All are terminated with standard Type K plugs.
-
product
Midirack - Installed Peripherals
OTP2-Modul-Nr044
The extension of the module can create new possibilities for your test system.
-
product
Accessories: Fixture
ICT I3070
View ICT i3070 fixture accessories ranging from fixture kits to vectorless test items like nanoVTEP. You can conveniently select items/parts to request for a Quick Quote.
-
product
IEC60068-2-75 Spring Hammer Test
CX-T03
Shenzhen Chuangxin Instruments Co., Ltd.
*Impact hammers are used to check the durability of enclosures for electrical appliances of other electronic products.If damage occurs from the Impact Hammer test .Accessibility probes can be used to measure the extent or severity of the damage.The Impact Hammer simulates the mechanical impact to which electrical equipment may be subjected. *This hammer is mainly used to test household and similar electrical appliances shell, lever, handle, knobs, lights and other shell to withstand mechanical shocks.* The impact tester made of stainless steel or alloy.
-
product
Surface Mount-to-DIP JEDEC SOT-25, SOT-23A-6 Adaptor
1110748
Surface Mount to DIP Adapter for SOT-25, SOT-23A-6. Allows for breadboarding or substitution of microgate SOT-23A-6 and SOT-25 IC and transistor packages into .100 [2.54] pitch proto boards or PC boards. Solder masked top-side pads allow user to hand solder devices directly to topside of adapter with fewer problems of solder bridging. Longer male bottom pins are available at special request for easy use of probe clips. Large topside pads allow for soldering test pins, jumpers, etc. to top of adapter.
-
product
3U CPCI 32-bit Test Extender
Measurement and testing of CompactPCI® assemblies in the 3U Euro-board form factor is greatly facilitated by the use of this test adapter. Easy access to the DUT is guaranteed because the adapter has plug-in connections on 3 sides. The Modern BRIDGE design permits up to 3 CompactPCI® cards and one standard PCI® card to be inserted in one CompactPCI® slot. This allows system developers to implement a large number of tests with little effort and enables you to achieve vital time to market.
-
product
Redundant Strap down INS ATE Test Station
Redundant Strap down Inertial Navigation System (RESINS) checkout test station comprises of cPCI chassis with various functional I/O modules like ADC, DAC, DIO, VFC, Relay matrix, MIL 1553, GPIB, Serial communication interfaces and Custom Built System interface adaptor.
-
product
Micro Compression Tester
MCT Series
This is a strength evaluation tester for micro parts and micro particles generated in powder processing. It is capable of carrying out not only compression tests, but also loading and unloading tests, repeated tests, and various other load patterns, with excellent operability and functionality.
-
product
PXI 10W Programmable Resistor Module, 1-Channel, 1.5Ω to 472Ω
40-253-020
The 40-253-020 is a programmable resistor module with 1 channel which can be set between 1.5Ω and 472Ω with 0.125Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Semiconductor Electrical Test
We conduct electric property test (final test) of the completed (packaged) LSI products. We will support testing of analog devices, logic devices, other electronic parts, modules, application products and so on. We will test according to customer's specification regardless of evaluation, trial production, mass production, by know-how cultivated with long-time mass production results. Test initial examination ~ From consistent correspondence up to selection and evaluation, individual correspondence such as design only is accepted.
-
product
Test Port Adapter Set, 2.4 Mm To 3.5 Mm
85130F
The Keysight 85130F test port adapter protects the test set port from connecting directly with the device under test. It has a special rugged female connector designed for connecting to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. The set contains a 2.4 mm to PSC-3.5 mm male adapter and a 2.4 mm to PSC-3.5 mm female adapter. The frequency range for these adapters is dc to 26.5 GHz with a return loss of 26 dB or better.
-
product
Stationary Test Equipment
Single- and three-phase, standardized and individual test systems are covering all legal metrological test requirements for simple meters, high precision multifunction meters, smart meters and reference standards. Flexible and modular system components for the optimal customer orientated solution.
-
product
Milli Volt Drop Test Set
Widely used for testing transformer and switchgear, this equipment is available to clients in different capacities.
-
product
Fixtures, Programming & Test Services
Comware Technical Services, Inc.
Fixtures and programming services are available for Agilent, GenRad, and Teradyne testers. Working from CAD data, a program can be created in only a few days allowing for fast and cost effective testing of your products. Engineering services are available for fixture revisions or repairs.
-
product
Test System
Griffin III
The Griffin III system brings new price/performance efficiency to the Tester-in-a-Head tradition, a concept created and introduced by HILEVEL in 1987. This tester is a superior cost-effective solution for Engineering, Production, and Failure Analysis test applications.
-
product
Film Tearing Strength Tester
DRK108C
Shandong Drick Instruments Co., Ltd.
DRK108C Tearing Tester is applicable in the tearing test of films, sheets, flexible PVC, PVDC, waterproof films, woven materials, polypropylene, polyester, paper, cardboard, textile and non-woven, etc.
-
product
External DC Bias Adapter
16200B
The 16200B test fixture is designed to operate with high frequency LCR meters and impedance analyzers. It allows you to supply a bias current across the device of up to 5 Adc through a 7 mm port by using an external DC current source.
-
product
Mechanically-linked AWD dyno
MD-AWD-800 Series
Like all Mustang dynos, the MD-AWD-800 includes all of the advanced tuning capabilities that are included with the standard PowerDyne Software application such as constant speed, constant torque, step tests, and elapse time tests like 1/4 sprint all performed using Mustang''s patented Vehicle Simulation technology where the dyno automatically controls the loading to simulate actual "on-road" conditions.
