-
product
Floating 6-Ch Integrated Power Source
PM0650
The pulse channels provide voltage pulses with duration control 10us to 100ms, and measures current. The combination of capabilities provides a versatile solution on fulfilling the wide range of requirements on testing a device. The PM0650 may be floated up to ±1500V to facilitate HV isolation test of devices where outputs may be connected directly to line voltages.
-
product
12-Ch 10A-250VAC RCV Power Distribution Unit
YAVAR438
- Hardware controlled Enable Input- 12 Power relays up to 10A 250VAC/DC and 300W or 2.700VA switching power- 12 10-mOhm shunt resistors.- 6 Switched 2-Pole sense channels- Single phase isolated or 3-Phases non-isolated switching capabilities, to or from the device under test (power or load)- VPC TriPaddle 96 pins connector.- NI LabView & TestStand driver.- .NET, C/C++, VB driver.- Soft Front panel for direct interface.- CAN Control or Ethernet (with Ethernet to CAN Gateway).- Self-test module available.- Form A
-
product
Flexible Cable Set, 2.4 Mm To 3.5 Mm
85134F
The Keysight 85134F is a 62.9 cm (24.75 in) long1 flexible cable set composed of a 2.4 mm female2 to PSC-3.5 mm female connector and a 2.4 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss greater than or equal to 16 dB. Insertion loss is 0.31 * sqrt (f) + 0.2, where f is frequency in GHz, for the test port connector and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is specified with a 90 degree bend using a 4 to 3 inch radius. Stability1 of the Keysight 85134F is less than 0.12 dB and phase is 0.13*f+ 0.5°, where f is frequency in GHz.
-
product
Boundary Scan Tester and Programmer
JTAGMaster
The JTAGMaster Tester and Programmer is designed to work with ABI's bespoke software - a multiple purpose platform which enables users to freely configure test procedures and instruments. Integrated functions are also available to the user to automatically learn the device status, provide pin-to-pin comparison and information as well as use some reporting facilities.
-
product
Test Probes
E-Series
Your product descriA full portfolio designed for general purpose test on bare boards, surface mount assemblies and other forms of test specially to meet any needs.ption goes here.
-
product
Test System
DA-2 ATS
The DA-2 ATS is an economical Commercial-Off-The Shelf (COTS) build-to-print tester. The test station is compliant with the published drawing package. The system does not include software.
-
product
Shock Test Systems
Accurately measure the fragility of products and evaluate how they respond to specific shock inputs.
-
product
Semiconductor Automatic Test
Qmax Test Technologies Pvt. Ltd.
Semiconductor Automatic Test by QMax
-
product
±6 kV ANSI/ESDA/JEDEC HBM Test System
HBM-TS10-A
High Power Pulse Instruments GmbH
*±6 kV Human-Body-Model (HBM) tester according ANSI/ESDA/JEDEC JS-001 standard with C = 100 pF, R = 1.5 kΩ discharge network*Wafer, package and system level HBM testing*True HBM: the classical discharge network of the HBM-S1-A according the standard ensures compliant waveforms for all load conditions*No trailing pulses*Integrated 10 kΩ charge removal resistor*Integrated DUT HBM current sensor for real time transient current monitoring with 1V/A output sensitivity into 50 Ω digital oscilloscope i...show more -
product
Test Valva Score
AI
Test Value Score is a revolutionary AI-powered feature that dynamically assigns a score to each test according to the contribution it provides to the testing process. The Test Value Score allows Test Managers to optimize their testing operation under time constraints and budget limitations.
-
product
Large Current Battery Short Circuit Test Device
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL Large Current Battery Short Circuit Test DeviceApplication: Battery Module, Battery Pack, Battery System short circuit.Short Circuit Mode: Pneumatic drive contact + Vacuum Interrupter
-
product
DataBlaster PCI / PCIE JTAG Boundary-Scan Controller
JT 37x7/PCI
High speed and performance JTAG Boundary-scan PCI PC plug-in controller for PCI bus slot or PCIe PC plug-in controller for PCI Express bus slot.The controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘
-
product
Test Leads
designed for electrical and electronics testing in today’s industrial environment.
-
product
Partial Discharge Test Equipment
Wuhan Huatian Electric Power Automation Co., Ltd.
Partial discharge detectors for high voltage equipment.
-
product
Power Supply
A power supply provides the required power for a test application or additional devices. A constant output voltage is generated from an unstabilized input voltage.There are single-channel or multi-channel models with fixed or programmable output voltage. Other features include programmable current limiting or safety functions such as overvoltage protection (OVP) or overcurrent protection (OCP).
-
product
Automated Testing System
PV-LIT
Thermographic solutions ensure high quality of solar cells and modules.Usable for all types of solar cells and modules (silicon-based or thin-layered)Testing in laboratory and in-line in the course of the manufacturing processTesting of various solar cells and modules through contact and non-contact measurementCell-specific system configuration and determination of test criteria and kind of defects
-
product
PXI Automotive Switch Simulator Modules
Pickering's Switch Simulator Modules are designed for automotive test applications. These modules simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. They allow automotive I/O devices to be tested for correct operation under adverse conditions.
-
product
Antenna, Log Periodic
EM-6944 | 200 MHz – 3 GHz
The EM-6944 offers an exceptional combination of frequency coverage from 200 MHz – 3 GHz and high power handling capability without compromising the consistent performance versus frequency that makes the log periodic antenna so desirable for test applications.
-
product
Fiber Optic Power Meters
FOD 1202H
The FOD 1202 & FOD 1202Si triple wavelength power meters are reliable, rugged and hand-held test product. InGaAs & Si Version with triple wavelength calibration
-
product
Pin Moisture Meter with Bluetooth®
FLIR MR55
The FLIR MR55 is a pin-based meter with wireless connectivity, which offers the convenience to view readings from a mobile device via the FLIR Tools® Mobile app. Thanks to a built-in library of 11 material groups, users can tune the meter to the appropriate test material to improve measurement accuracy. This library is easy to access on the FLIR.com website by scanning a QR code on the back of the meter with a mobile device.
-
product
Ground Grid Tester
GGT Series
The GGT500 ground grid integrity tester is designed for inspection of the substation ground grid. It can also be used as a portable micro-ohmmeter with Both Sides Grounded and Remote Control functionalities. It is intended to inspection the conditions of a grounding system beneath substations, testing of medium- and high-voltage circuit breakers, disconnecting switches, high-current bus bar joints, cable splices, and different high-current links.In the United States when inspecting the quality o...show more -
product
Datacom Analyzers
Wuhan Sunma Technology Co., Ltd.
SunmaFiber provide E1/2M Transmission Analyzer is one multi-functional and full- featured digital transmission system test device, designed for the installation test, engineering check and acceptance, daily maintenance of digital networks, mainly performing channel test, alarm analysis, fault finding and signal analysis. In addition, this instrument further provides various protocol converters with one-way and bi-directional bit error test function. These capabilities make it ideal for field use.
-
product
Battery Emulation
NH Research, Inc.’s (NHR) is an industry leader of battery test solutions. NHR’s battery emulators include the High-Voltage Battery Emulator (9300) Series and Medium Voltage Battery Emulator.NHR’s battery emulators are used to emulate a battery rather than using a real battery which dramatically reduces testing time, provides highly repeatable test results, and creates a safer test environment. Battery emulation (or simulation) eliminates preparation time, operator errors, and result variations due to battery temperature or aging. It substantially reduces test time, energy consumption and operating costs.
-
product
High Power Programmable AC Source With Transients
Chroma Systems Solutions, Inc.
Ideal for commercial, power electronics, avionics, military, and regulation test applications from bench-top R/D design verification to quality assurance and mass production
-
product
T3DSO2000A Series Oscilloscopes
T3DSO2000A Series
Teledyne Test Tools T3DSO2000A Oscilloscopes feature two channel and four channel models with analog bandwidth options from 100 MHz to 500 MHz. Each model offers a maximum sample rate of 2 GSa/s, and a maximum memory depth of 200 Mpts in half channel mode. All models incorporate two 2 GSa/s ADCs and two 200 Mpts memory modules. When all channels are enabled, each channel has sample rate of 1 GSa/s and a standard record length of 100 Mpts. When only a single channel per ADC is active, the maximum sample rate is 2 GSa/s and the maximum record length is 200 Mpts. For ease-of-use, the most commonly used functions can be accessed with its user-friendly front panel design.
-
product
Formation Damage
Formation Response Testers (FRT) are designed to accurately measure the permeability changes of a formation sample when exposed to a variety of test fluids.
-
product
MPI PA Wafer Probers
MPI Photonics Automation is the industry-leading provider of turnkey wafer test and measurement solutions. We offer a complete line of high-performance wafer probers designed to address the diverse and complex needs of the Photonics, Optoelectronic, Semiconductor, and Laser industries.
-
product
Special Test Equipment
Complex products require demanding and versatile test systems capable of complex test cycles. The final objective is to ensure the validation of the final product during the different stages of the production process.
-
product
ATG CASSETTE PROBES
SERIES 110
ElectricalMAXIMUM CURRENT: 3 amps continuousat working travel, non - inductiveRESISTANCE: At 35 mA test current,50 mOHMS meanMaterial and FinishesPLUNGER: Heat treated berylliumcopper, 24 Kt gold plated over nickelBARREL: Nickel silver with 24 Kt goldplated ID and OD over nickelSPRING: Music wire, 24 Kt gold platedover nickelPIN: Heat treated berylliumcopper, 24 Kt gold plated over nickel
-
product
Calibration
Calibrations of electronic equipment is one of the activities that Kiwa Dare offers to its clients. these calibrations are under accreditation in the field of electrical quantities. Besides calibrations in the field of DC current, DC voltage and low frequency (test and measuring) equipment, Kiwa Dare is specialized in calibrating high frequency measuring equipment and in particular EMC equipment in a frequency range of (DC) 40 GHz. New the site validation calibrations whereby Kiwa Dare can calibrate shielded rooms (Faraday room) and anechoic chambers under accreditation.
