Safety Test
Check to determine whether a device is free from hazards.
-
Product
HV Enclosures with Integrated Safety Test
-
The HV test hood according to Performance Level e (ISO 13849-1), developed by us according to the EN50191 standard (erection and operation of fixed and temporary electrical test installations), offers the highest safety for the operator. The large test chamber is enclosed with a hood made of sturdy, highly insulating and transparent plastic. During the test, there is a clear view of the test specimen. A signal light visually indicates safe opening when the light is “green”. “Red light” symbolises danger, the hood cannot be opened due to the safety interlock. The safety switch also ensures that the hood cannot be opened during the test. This means that the test hood fulfils all the required specifications for compulsory contact protection.
-
Product
Hipot & Safety Test
-
Chroma Systems Solutions, Inc.
Electrical safety tests to comply with IEC, UL, TUV, CSA, EN, and other electrical safety requirements.
-
Product
Safety Test Panel for Mixer
-
SCR ELEKTRONIKS introduces Safety Test Panel for Domestic Mixer with PC Datalogging. The tests are Performed as Prescribed in IS the Panel Carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 20 seconds. Micro controller based sequential timer maintains the sequence of operation and displays the test status. This manual contains information about operating instructions and maintenance of the equipment. Please go through this manual carefully and retain it for future reference.
-
Product
Safety Compliance Test System
EN 60601
Test System
Test system for electrical safety compliance testing of medical products in accordance with EN 60601-1, 3rd edition.The system is equipped with three test fixtures which are connected in parallel order to reduce the number of setup tasks for different variants in the course of day-to-day manufacturing processes. Its purpose is to test medical products, e. g. patient monitors, which are employed at hospitals to monitor heartbeat and oxygen saturation.Based on the integrated electrical safety tester by Associated Research, in combination with an AC power source and a switching matrix, it is possible to fully automate tests like for instance AC/DC high-voltage tests, insulation resistance measurements, earth connection tests and leakage current measurements.The required occupational safety is provided by a high-voltage safety hood in accordance with EN 501191. The entire safety technology, as well as the control PC, is mounted in an aluminum-profile cart.
-
Product
Electrical Safety Test Solutions
-
Hipot Analyzers with 500VA output rating can be used to test and analyze the withstand voltage of high power and leakage current for the products like motor stators and rotors with high parasitic capacitance. Corona detection can be used for turn-to-turn or turn-to-ground test to avoid winding insulation failure from corona discharge.
-
Product
Pulsed Withstand Voltage Safety Test
-
Suzhou 3ctest Electronic Co.,Ltd.
designed to test the induced and conducted disturbance on the telecom lines generated by power line and electrical railway. It meets the requirements of YD/T 993-2006(The technical requirements and test methods of over-voltage and over-current resistibility for telecommunication terminal equipment),
-
Product
Automatic Safety Test System
LS9955/56
-
The LS9955/LS9956 Automatic Safety Test System is according to GB4706.1, IEC/EN60335-1, UL60335, GB7000, IEC60598, GB4943, IEC60950 and GB9706.1. It used for luminaries, home application and motor tools safety test in production line or Lab R&D.
-
Product
Pulsed Withstand Voltage Safety Test
-
Suzhou 3ctest Electronic Co.,Ltd.
Designed to test the induced and conducted disturbance on the telecom lines generated by power line and electrical railway. It meets the requirements of YD/T 993-2006(The technical requirements and test methods of over-voltage and over-current resistibility for telecommunication terminal equipment), ITU-T K21 and ITU-T K44.
-
Product
High Current Generators
-
Quantum Composers is a recognized industry leader for Current Pulsers and Firesets. We specifically design our units for use in pyrotechnic applications such as Aerospace, Defense, Propulsion, and Automotive Safety and Squib testing. Our current generators are used throughout the world in demanding and harsh testing environments where quality, reliability, and safety are paramount. We are also an excellent replacement and upgrade solution for legacy equipment.
-
Product
Safety Valve Test Bench
-
Nagman Instruments & Electronics Pvt. Ltd
Safety Valve Test Bench is a very easy, safe, accurate and maintenance free operating work shop test unit for Testing & Calibration of pressure/safety relief valve.
-
Product
Electrical Equipment Test System
C8900
-
Chroma Systems Solutions, Inc.
The 8900 electrical equipment ATS can complete measurement and test procedures simultaneously and automatically. This automated functionality decreases the risk of errors due to improperly written tests. Chroma 8900 solves the Electrical Safety Test and special FUNCTION test solution.
-
Product
Electrical Products
-
We offer a broad range of electrical testers, electrical analyzers, and electronic safety test equipment to help you measure AC and DC current and voltage, resistance, frequency, capacitance, harmonics, power energy, and more. Plus get the power supplies to keep your equipment running and the enclosures to protect your electrical and electronic products.
-
Product
PXI BRIC8 FIBO Matrix Dual 30x2 3pin brkout
40-595A-005
Matrix Switch Module
The 40-595A is a matrix module based on the BRIC format that is designed for fault insertion applications in safety critical testing. As with other BRIC modules the matrix size can be scaled to suit the user application. The 40-595 has a very high current rating of 10 Amps, ideal for higher power systems, and can be used as a conventional matrix.
-
Product
Automated Testing Systems
-
Instron’s automated testing systems bring precision, productivity, and safety to materials testing by automating routine tensile, flexural, and compression operations. Available as full turnkey platforms or modular add-ons for existing test frames, these systems — including the AT3 three-axis, AT6 six-axis robotic, AT2 automated XY stages, CT6 cobot integration, and carousel stations — allow labs to boost throughput, reduce operator variability, and free up staff for higher-value activities. The systems are engineered to support a wide spectrum of materials (plastics, metals, films, composites, medical devices) and comply with international ASTM and ISO test standards while enhancing repeatability and workflow efficiency.
-
Product
Wound Component EST Analyzer
19036
Analyzer
Chroma 19036 is the industry's first wound component electrical safety test (EST) analyzer that combines the functions of impulse test, hipot, insulation resistance and DC resistance measurements. It has 5kVac/ 6kVdc high voltage output, 5kV insulation resistance, 6kV layer short impulse voltage and 4-wire DC resistance measurement that can comply with the wound components test demands by providing maximum 10 channels output for multichannel scanning tests to save time and labor costs.
-
Product
LST-2000 Laser Safety Test System
-
Hangzhou Everfine Photo-E-Info Co., LTD
The system can measure the spectral power distribution, radiant power, radiant energy, apparent light source size, pulse energy and other parameters of the laser light source, and classify the laser light source according to the standard IEC 60825.1. Because laser measurement involves more condition parameters, limit calculation and judgment process is complex, so this system adopts systematic design, the measurement complexity is simplified, the hardware adopts componentization module, users only need to follow the software prompts, carry out the corresponding steps of operation can accurately measure the effective radiation value under the corresponding conditions. The software calculates the relevant reachable emission limits and automatically classifies the laser product's safety level.
-
Product
Custom Testing
-
You create a custom test plan (a file that lists a series of tests to be run), to meet requirements specific to your environment and apply that test plan to any number of clusters. You specify the order in which tests run and the specific components to be tested. After you set up your custom test environment, you run the test procedure from SMIT and view test results in SMIT and in the Cluster Test Tool log file. For information about customized testing, see Setting up custom cluster testing.*Fixture Design*Fixture Fabrication*Custom Test Stands*Prototype Testing Services*Product Safety Testing Services
-
Product
Electric Safety Tester
PV-215
-
The multifunction device PV-215 allows quickly and safely carrying out the electric safety tests provided for a PV system (section in DC) and the functional test of modules/strings the system consists of according to the requirements of Standard IEC/EN62446.
-
Product
Electrical Safety Analyzer
-
Guarantee the safe operation of your electrical equipment with Netech’s Electrical Safety Analyzers. We offer three versatile electrical testing tools which can be used for a variety of safety testing on devices including hospital equipment and patient monitoring equipment. Scroll down to see an overview of our electrical safety analyzer models.
-
Product
Hydrostatic Test Stand, Hydraulic System Components
9901HTX-100LR2-36x36x15
-
The 3 ft. wide x 3 ft. deep Hydrostatic Test Stand, Hydraulic System Components is utilized for pressure testing hose and tube assemblies as well as any component requiring hydrostatic testing in the integral safety test chamber.
-
Product
Programmable Insulation/Withstanding Voltage Tester
-
AllWin Instrument Science and Technology Co., Ltd.
1. Electric safety wall detecting2. Test mode programmable3. ACW to DCW to IR toggle automatically4. (40.0~400.0)Hz
-
Product
Multifunctional Safety Tests
-
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
Product
Guardian Hipot Analyzer
19055
-
Chroma Systems Solutions, Inc.
Hipot or dielectric withstand testing instruments manufactured by Chroma are used for conducting electrical safety tests on electrical components and products to make certain they are in compliance with IEC, UL, TUV, CSA, EN and other electrical safety requirements. In addition, these instruments are designed for general product or component testing as well as complex medical safety testing (60601-1) ensuring human safety and product reliability.
-
Product
Electrical Safety Analyzer
19032
-
Chroma Systems Solutions, Inc.
Our Electrical Safety Analyzers combine Hipot, Insulation Resistance ( IR), Ground Bond (GB), Leakage Current (LC)/AC LC/DC LC, and Dynamic Function Tests. Savings can be up to 50% of production line space by not having to purchase and rack several safety test instruments. It also increases efficiencies of electrical safety testing and reduces associated labor costs.
-
Product
Turn-Key Test Solutions
-
Our Product line cover the very basic of safety test needs. We have products focus on single safety test like Hipot, Ground-Bond, Leakage-Curret and Insulation Resistance. Advanced models combining all the safety tests function together.
-
Product
Wound Component EST Scanner
19035
-
The quality verification tests for wound components consist mainly of AC/DC Hipot tests and insulation resistance (IR) tests. The Chroma 19035 wound component EST scanner series perform safety tests for motor, transformer, and heater related wound products.
-
Product
Luminaire Testing
-
Product Safety Consulting Inc.
With the emergence of LED technologies, being part of the renewed energy scene requires knowledge of how to design products to meet consumer needs while passing even more stringent safety testing than ever before. Staying on top of the new testing requirements, from local and global standpoints, is what we do. Standards generally are not clear; they leave room for interpretation and often present constraints to product design. At PSC, we offer solutions to non-compliance rather than simply reporting a pass/no-pass statement. And, we communicate with straightforward explanations of safety issues that often arise during the testing process. Our expert product testing team understands what you need to do to achieve compliance. Failing at the testing stage only costs you valuable time and money. It allows the competition to beat you to the sale and takes resources away from future growth.
-
Product
Transient Over-voltages Tester
SUG335
-
The SUG335 is a 1.2/50μs Transient Over-voltages Tester. The polarity interval time can be at least 1s. The standard voltage waveform complies with the IEC 60335, IEC61180, IEC 62052-11: 2003, IEC 61008-1: 1996, IEC 61009-1:1996 and IEC 60947-1: 1995, IEC60060, IEC1036 surge voltage test and has been used for safety testing to determine if the clearance was fulfilled the safety requirement while the transient voltage in the circuit.
-
Product
PXI BRIC8 FIBO Matrix Dual 18x4 3pin brkout
40-595A-008
Matrix Switch Module
The 40-595A is a matrix module based on the BRIC format that is designed for fault insertion applications in safety critical testing. As with other BRIC modules the matrix size can be scaled to suit the user application. The 40-595 has a very high current rating of 10 Amps, ideal for higher power systems, and can be used as a conventional matrix.
-
Product
Product Safety Testing & Certification
-
MET has been certifying, listing, and labeling products for electrical product safety for more than 40 years. In that time, MET has certified thousands of products for compliance to electrical safety standards. This translates into literally millions of products sold in the U.S. and Canada labeled with the MET Mark.
