Safety Test
Check to determine whether a device is free from hazards.
-
Product
Wound Component EST Analyzer
19036
Analyzer
Chroma 19036 is the industry's first wound component electrical safety test (EST) analyzer that combines the functions of impulse test, hipot, insulation resistance and DC resistance measurements. It has 5kVac/ 6kVdc high voltage output, 5kV insulation resistance, 6kV layer short impulse voltage and 4-wire DC resistance measurement that can comply with the wound components test demands by providing maximum 10 channels output for multichannel scanning tests to save time and labor costs.
-
Product
Product Safety Testing
-
D.L.S. Electronic Systems, Inc
D.L.S. Conformity Assessment is a fully staffed and accredited product safety testing and consulting organization within the D.L.S. corporate umbrella. The Conformity Assessment group offers full compliance testing services for North America, Europe, Pacific Rim, and other global regions including testing to these standards:
-
Product
Multifunctional Safety Tests
-
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
Product
High Voltage Safe Measurement Systems
-
For measurement on high-voltage components with certified safety – in test drives, field tests, and on test benches: CSM’s high-voltage measurement systems are specifically designed for the safe and accurate acquisition of temperatures and analog sensor signals in HV environments, especially in electric and hybrid vehicles.
-
Product
Multifunctional testers
MI 3152H EurotestXC 2,5 kV
-
MI 3152H EurotestXC 2,5 kV is an instrument from the new generation of Metrel’s multifunctional measuring instruments. The already well known functions like complete installation safety testing according to IEC/EN 61557 and AUTO SEQUENCE testing of TN and TT earthing systems expanded with insulation resistance measurement with the test voltage up to 2,5 kV are managed by a completely new user interface based on large colour touch screen display.
-
Product
Mobilize Electrical Safety Analyzer And Tester
Safe-T Sim®
-
The world’s smallest automated electrical safety analyzer is designed to perform all electrical safety tests with the touch of one button. Advanced features and half the cost of other automated safety analyzers. User-defined tests with programmable Pass and Fail limits. Wireless technology plus our app provide the capability to control the Safe-T Sim and generate a complete electronic test report right from your smart device!*
-
Product
Hybrid Wound Component EST Scanner
19035
-
Chroma Systems Solutions, Inc.
The quality verification test items for Wound Components consist of AC/DC Hipot tests and Insulation Resistance (IR) tests. Chroma integrates the above tests into the Hybrid 19035 Wound Component EST Scanner series to perform safety tests for motor, transformer, and heater related wound products. The wound component manufacturers performing quality verification testing will not only have reliable quality, but also can control product quality efficiently.
-
Product
Mobility Simulator Creates V2X Environments For Testing
MxDrive™
-
MxDrive is a multi-vehicle and infrastructure mobility simulator that provides an environment to generate and run real-world conditions to test connected vehicle applications. Testing V2X applications on actual roads has limitations. Only a limited number of test conditions can be achieved, while safety and damage risks further limit test coverage. MxDrive combined with the MxSuite ecosystem significantly simplifies the testing of Advanced Driver Assistance Systems (ADAS), Sensor Fusion, Radar, and V2X. MxSuite is ISO 26262 qualified to test safety applications for OEMs and suppliers.
-
Product
Hipot Tester
19070
-
Chroma 19070 series are the smallest Hipot Testers currently available in the world. Its super mini size is easy to carry and the large LCD display is suitable for viewing measurement results. These sophisticated hipot testers are most applicable to safety test for electronic components.
-
Product
Battery Washing Tester, Battery Safety Testing
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's newly battery washing tester consisting of test chamber and washing chamber under test chamber. Moreover, it motorized rotary propeller mounted inside of test chamber and on internal wall of test chamber, drying system is mounted.
-
Product
Medical System
Sentinel III
-
Chroma Systems Solutions, Inc.
The Sentinel III System provides complete Electrical Safety Testing to IEC60601-1 and IEC 60601-2-49 (Multifunctional Patient Monitoring Equipment) in a fully automated fashion. The Sentinel III saves time by scanning patient connections for leakage current without powering down the device.
-
Product
Medical System
Sentinel II
-
Chroma Systems Solutions, Inc.
The Sentinel II system provides fully automatic Electrical safety testing to IEC/EN/UL/CSA 60601-1. Sentinel II saves time by scanning patient connections for leakage current without powering down the medical device.
-
Product
Safety Test Panel for Luminaire Fixture
-
SCR ELEKTRONIKS introduces Safety Test Panel for Luminaire with PC Datalogging. The tests are Performed as Prescribed in IS the Panel Carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing.
-
Product
PCIe Gen3 High Speed, Compact Camera for Testing
CB013CG-LX-X8G3
-
High speed, compact, fast camera for: Vehicle Impact, Airbag Deployment and Safety Restraints Testing, Digital Image Correlation (DIC), Projectile, Explosives, Ballistics, Combustion and Missile Launch Tracking, Fluid and Flow Visualization, Sports Broadcasting, Commercial Film, Television and Studio Production, Fluidics and Particle Image Velocimetry (PIV), Flat panel inspection (FPD), printed circuit board (PCB) examination and more.
-
Product
Pulsed Withstand Voltage Safety Test
-
Suzhou 3ctest Electronic Co.,Ltd.
Designed to test the induced and conducted disturbance on the telecom lines generated by power line and electrical railway. It meets the requirements of YD/T 993-2006(The technical requirements and test methods of over-voltage and over-current resistibility for telecommunication terminal equipment), ITU-T K21 and ITU-T K44.
-
Product
DC Hi-Pot Tester
3010HP, 3025HP & 3050HP
-
The DC Hi-Pot test is an important part and parcel of the electrical safety tests mandated by standards organization world-wide. More than 80 per cent of faults in electrical and electronic systems are due to weak insulation caused by environmental factors such as dirt, grease, temperature stress, humidity, etc that affect the dielectric strength of the insulation material.
-
Product
PXI BRIC8 FIBO Matrix Dual 30x2 3pin brkout
40-595A-005
Matrix Switch Module
The 40-595A is a matrix module based on the BRIC format that is designed for fault insertion applications in safety critical testing. As with other BRIC modules the matrix size can be scaled to suit the user application. The 40-595 has a very high current rating of 10 Amps, ideal for higher power systems, and can be used as a conventional matrix.
-
Product
Software
CaptivATE
-
Chroma Systems Solutions, Inc.
CaptivATE test software provides an electrical safety test solution for accurately performing automated hipot, leakage current and functional tests. Testing is made simple and fast by automatically downloading the test setup, conducting the required measurements and outputting the test results. Software supports IEC60601-1 test requirements and IQOQ protocol documentation.
-
Product
Safety Testing
-
Underwriters Laboratories Inc.
As the global safety science leader, our safety offerings and expertise are unparalleled. We can help you engineer safety into your products throughout your development process, reducing costs and challenges associated with innovative offerings. Our testing and certification services focus on helping our customers create a safer, more secure and sustainable world. Our mission of "working for a safer world" drives everything we do. Leverage our offerings and insights to build trust and confidence in your products and services.
-
Product
Automated Testing Systems
-
Instron’s automated testing systems bring precision, productivity, and safety to materials testing by automating routine tensile, flexural, and compression operations. Available as full turnkey platforms or modular add-ons for existing test frames, these systems — including the AT3 three-axis, AT6 six-axis robotic, AT2 automated XY stages, CT6 cobot integration, and carousel stations — allow labs to boost throughput, reduce operator variability, and free up staff for higher-value activities. The systems are engineered to support a wide spectrum of materials (plastics, metals, films, composites, medical devices) and comply with international ASTM and ISO test standards while enhancing repeatability and workflow efficiency.
-
Product
Safety Testing
-
Seaward's high quality electrical safety testing equipment has a worldwide reputation for technical excellence in the appliance, electrical and electronics manufacturing sectors.
-
Product
Battery Testing Chambers
-
We supply a variety of test chambers for testing small battery cells to large lithium ion battery packs. Battery test chambers are supplied to a variety of industries including telecommunications, computer and automotive. With the goal of reducing automobile emissions and the development of electric vehicles, the need for lithium ion battery testing is even more critical. Our proven experience provides the most cost-effective solutions. Each test chamber is built according to specific test requirements and may be interfaced with battery cyclers, control & monitoring data acquisitions systems and other test equipment for a complete integrated test solution. All environmental chambers are designed with safety in mind. A variety of safety features are provided for reliability and abuse testing of batteries. These features may be incorporated into CSZ test chambers and tailored to the various hazard levels of EUCAR (European Council for Automotive R&D), a consortium of European car manufacturers. To better assess the hazard potential of tests, EUCAR has investigated hazardous situations and divided them into eight risk classes. The development of the safety equipment of our battery test systems is also based on this classification. For each hazard level, we recommend specific safety options that can be included with your chamber to meet your specifications to safety test your product. Together with our customers, we assess which safety devices are necessary for the respective test chambers.
-
Product
PXI BRIC8 FIBO Matrix Dual 24x2 3pin brkout
40-595A-004
Matrix Switch Module
The 40-595A is a matrix module based on the BRIC format that is designed for fault insertion applications in safety critical testing. As with other BRIC modules the matrix size can be scaled to suit the user application. The 40-595 has a very high current rating of 10 Amps, ideal for higher power systems, and can be used as a conventional matrix.
-
Product
Turn-Key Test Solutions
-
Our Product line cover the very basic of safety test needs. We have products focus on single safety test like Hipot, Ground-Bond, Leakage-Curret and Insulation Resistance. Advanced models combining all the safety tests function together.
-
Product
Downloadable PAT Tester
Apollo 400+
-
The Apollo 400+ features a comprehensive range of electrical safety tests with user configurable test sequences and has storage for up to 2,000 test records. Compatible with our Seaward PATGuard 3 software for record keeping and reporting.
-
Product
Photovoltaic and Electrical Installation Testers
-
Photovoltaic electrical installation safety testing is a special area of electrical installation safety testing as it also entails tests and measurements on DC systems, which are relatively uncommon in most domestic, commercial and to a certain extent industrial environments. There is also the addition of photovoltaic-specific tests that are outside the realm of standard test and measurement procedures.
-
Product
Downloadable PAT Tester
Apollo 500+
-
The Apollo 500+ features a comprehensive range of electrical safety tests with user configurable test sequences and checklists for PAT, PPM and PPE. It has storage for up to 10,000 test records and is compatible with our Seaward PATGuard 3 software for record keeping and reporting.
-
Product
Battery Drop Tester for Battery Safety Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's battery drop tester is used to test the drop impact performance of large, heavy-duty packaging products by simulating real surface, edge, and corner differences.
-
Product
Test Prods
-
Test prod with 4mm plug, test prod with 2mm pin, safety test prod, test prod 2mm, test prod 4mm, miniature test prod.
-
Product
PXI BRIC8 FIBO Matrix Dual 12x2 3pin brkout
40-595A-002
Matrix Switch Module
The 40-595A is a matrix module based on the BRIC format that is designed for fault insertion applications in safety critical testing. As with other BRIC modules the matrix size can be scaled to suit the user application. The 40-595 has a very high current rating of 10 Amps, ideal for higher power systems, and can be used as a conventional matrix.
