-
Product
LTP-25 High Performance Long Travel Probe
LTP-25
ICT/FCT Probe
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 400Full Travel (mm): 10.16Recommended Travel (mil): 317Recommended Travel (mm): 8.05Overall Length (mil): 1,460Overall Length (mm): 37.08Full Travel Remark: Full Travel for LRP-25TJ: 340 (8.6) and Full Travel for all Ultra High springs: 350 (8.9)
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
High Voltage Amplifier
HA-405
-
* 400Vp-p(±200V DC)* 400mAp-p(±200mA DC)* Bandwidth: ≦1MHz(200Vp-p) *Slew Rate: 500V/us *Gain(AMPL):0~90(10 Turn VR) *DC Offset: ≦0~±200V(10 Turn VR+SW) *Output Resistor: 50Ω *Microprocess Control Protection
-
Product
Converter Signal Amplifier – 0…10 Vdc – DIN Rail
HD978TR4
-
Configurable signal converter amplifier with 0…10Vdc (10…0Vdc) output. Input range -10 ..+60 mVdc. Standard configuration 0…20 mVdc.
-
Product
Amplifiers
-
Packaged and Die up to 26 GHzOver 145 MMIC Surface Mount and Die modelsConectorized models, power output to 100WHigh dynamic range, low noiseLow-cost, custom solutions available!
-
Product
Ball Bearing Linear Stage,13mm Travel XYZ, Sensitivity 3um
APSM13(A)-34
-
Model:APSM13(A)-34Ball Bearing Linear Stage,13mm Travel XYZ, Sensitivity 3umDetails&Spec: Please refer to PSM13(A)-34 Specification,It is combinated by2pcs PSM13(A)-34 (C,SR,SL) and 1pc PSM13(A)-34CZ
-
Product
Low Noise Amplifiers
-
LNA is an outstanding and mature product line of Skylink Microwave. We provide high performance low noise amplifiers in the industry, with reliable and rugged quality. Ultra low noise, ultra broadband and compact size are our specialty and enduring pursuit. Our engineers are committed to satisfying higher custom requirements of our customers and insist on designing optimized products to meet market challenges. Skylink Microwave provides you an extensive line of low noise amplifiers and the most economical choices.
-
Product
Optical Power Meter for 400-1550 nm Wave
F-712.PM1
-
Physik Instrumente GmbH & Co. KG
This photometer can convert an optical signal into a voltage signal in high resolution and with an extremely high bandwidth. The design of the optical input enables measuring of the optical signal independent of the position of the optical fiber in the connector. Wavelength range: 400 to 1550 (1) nm
-
Product
150 kHz-230 MHz Broadband Power Amplifiers
-
Output power up to 80W for standard conducted immunity testing. Our 150 kHz-230 MHz amplifier range covers output power ranging from 20 W to 80 W.
-
Product
100-Amp Current Calibrator And AC/DC Transconductance Amplifier
2555A
-
World’s Leading Precision 100-Amp AC/DC Current Standard - For 30 years Valhalla Scientific’s design has proven rock-solid reliability in metrology labs worldwide. The 2555A is a calibration powerhouse with wide-ranging applications and unsurpassed quality.
-
Product
Pneumatic, Contact, Receiver (with valve), Hose Barb, for 1/8" [3.2 mm] ID Tubing
610131107
Pneumatic Contact (Receiver)
Primary mating contact 610131106.Used in receiver module p/n 510104185, mates to contact p/n 610131106 and ITA modulep/n 510108160.
-
Product
Dual-Mode Charge Amplifiers
-
Dual-mode charge amplifiers represent a versatile solution for both piezoelectric charge mode and ICP® sensors. Among the advanced features offered by models 443B01, 443B02 and 2775C are an ultra-low noise floor, sensor fault detection, overload detection, a built-in calibration reference signal, and an RS-232 port for seamless computer control. Notably, model 443B02 features a long discharge time constant selection, ideal for capturing quasi-static events lasting several seconds, a capability particularly beneficial for ballistics and ammunition testing applications. Model 2775C features AC, DC, and servo outputs.
-
Product
LFLT-25 High Performance Lead Free Long Travel Probe
LFLT-25
ICT/FCT Probe
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 400Full Travel (mm): 10.16Full Travel Remark: Standard Spring: 400 mil / 10,16 mm, Alternate Spring 400 mil / 10,16 mm, High Spring: 400 mil / 10,16 mm, Ultra High Spring: 350 mil / 8,89 mmRecommended Travel (mil): 315Recommended Travel (mm): 8.00Overall Length (mil): 1,460Overall Length (mm): 37.08
-
Product
Millimeter Wave Zero Bias GaAs Schottky Diode
HSCH-9161
Diode Detector
The HSCH-9161 is suitable for medium-low barrier, zero bias detector applications. The HSCH-9161 is functional through W-band (110 GHz) and can be mounted in microstrip, finline, and coplanar circuits.
-
Product
High-Voltage Amplifier
ZET 420
-
The high-voltage signal amplifier for emission of acoustic signals through capacitive emitters: sonic detectors (without integrated amplifiers), piezoelectric emitters, and transducers.
-
Product
Amplifier
-
AEQORIS amplifiers achieve unrivaled technical specifications through sophisticated design.
-
Product
High voltage amplifiers (to ±500V)
-
These amplifiers provide high amplitudes and bandwidths, and are well suited for use as booster amplifiers for lower-voltage arbitrary waveform generators.
-
Product
Low Phase Noise Amplifiers
-
Low Phase Noise amplifiers are critical for many applications requiring high signal integrity. This is especially relevant in instrumentation, defense, and telecommunication applications where low phase noise amplifiers are becoming increasingly important as the oscillators improve. Phase noise is described as the close-in noise to the carrier that can often appear as jitter on a clock signal. Analog Devices offers a large portfolio of low phase noise amplifiers to meet a variety of requirements in the LO network, receiver, as well as in the transmitter. Our portfolio supports a wide range of power levels and frequencies to provide the right solution for the given application.
-
Product
System Amplifiers
-
The perfect combination of high performance, wide bandwidth and low noise
-
Product
Converter Signal Amplifier – 0…10 Vdc – Wall Mounting
HD978TR6
-
Configurable converter signal amplifier with 0…10 Vdc (10…0 Vdc). Input measuring range -10 ..+60 mVdc. Standard configuration 0…20 mVdc. Minimum measuring range 2 mVdc.
-
Product
CATV Amplifiers
-
Electronic devices that boost weak TV and broadband signals (audio, video, data) traveling through coaxial cables, compensating for signal loss from splitters, long cable runs, or network nodes to maintain strong, clear picture/data quality for multiple devices, operating across specific frequency bands for both forward (downstream) and reverse (upstream) paths.
-
Product
Square Wave Patterns (Ronchi Gratings/Rulings)
-
Square Wave patterns (Ronchi Gratings/Rulings) have extremely sharp edges. At APPLIED IMAGE, this sharpness is achieved through our unique manufacturing capabilities and processing technologies which produces the sharpest edges available anywhere. Our standard line of Ronchi Gratings is offered on Chrome on Glass (CG) and Photo Paper (RM).The Ronchi rulings are available on other substrate materials such as B270, quartz, BK-7, and White Opal as well as in English frequency metrics (cycles per inch).
-
Product
Motion Control Terminal Board For Mitsubishi J2S-A Servo Amplifiers
DIN-812M0
Terminal Board
- On-board connector type: 100-pin SCSI-II female- Suitable for Mitsubishi J2 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8132
-
Product
Power Amplifier, RF
-
Is a type of electronic amplifier that converts a low-power radio-frequency signal into a higher power signal. Typically, RF power amplifers drive the antenna of a transmitter.
-
Product
Low Noise Amplifier
LNA
-
Teledyne Defence & Space (TDS) Low Noise Amplfiers (LNA) are designed to amplify very low power signals without degrading the signal-to-noise ratio.An amplifiers is designed to increase the power of both the signal and the noise however the Low Noise Amplifier is specifically designed to minimise the additional noise so important information should not be lost.
-
Product
VCOM Amplifiers And Calibrators
-
Renesas offers various VCOM amplifiers including rail-to-rail input-output operational amplifiers and rail-to-rail input-output buffers, as well as programmable VCOM calibrators that are ideal for display applications.
-
Product
Amplifiers
-
Use our optical amplifiers to improve the signal-to-noise ratio (OSNR) and range performance of optical transmission systems.
-
Product
Isolation Amplifiers
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Unipolar and bipolar DC input signals 20 mV to 200 V and 0.1 mA to 100 mA calibrated range selection. Working voltage up to 1000 V AC / DC.
-
Product
Time & Frequency Distribution Amplifiers
-
Brandywine offers a wide range of high quality, state of the art signal timing distribution amplifiers, all with very low phase noise. These precision timing signal distribution amplifiers offer a variety of time and frequency signals and interface formats including IRIG A, IRIG B, Have Quick, 1PPS, as well as low phase noise reference frequencies. All of our distribution amplifiers feature dual inputs with automatic failover and multiple independently buffered outputs.
-
Product
RF Power Amplifiers
-
RF power amplifier category from Pasternack have components packaged in a hermetically-sealed metal enclosures and exhibit outstanding performance in high gain, gain flatness, high linearity and wide dynamic range. RF power amplifiers have excellent performance by using a hybrid microwave integrated circuit design and advanced GaAs pHEMT components. These SMA power amplifier modules are unconditionally stable and include built-in voltage regulation, bias sequencing, and reverse bias protection for added reliability.RF power amplifier over-voltage protection is installed externally for easy repair. These high reliability radio frequency power amps are fully matched internally for 50 Ohm input and output. This 50 Ohm power amplifier matching helps eliminates the need for any additional sensitive external RF tuning components.Our power amps are ideally suited for high linearity applications. These radio frequency power amplifiers offer small signal gain over a temperature range. The Pasternack RF power amplifiers have excellent gain flatness ranges and the IP3 output performance.Most all Pasternack RF power amplifiers are EAR99
