-
Product
LVDT Sensor Amplifiers
-
Analog Devices signal conditioning ICs, together with linear variable differential transformers (LVDTs), can be used to convert mechanical position to a dc voltage. The IC provides both the excitation for the LVDT and the output conversion to dc level with a user selectable gain. ADI LVDT signal conditioners are available to interface with a wide range of LVDTs, including half bridge and standard 4- and 5-wire.
-
Product
Pitot Tubes
-
The dpm-i Pitot Tube is a new design concept in Pitot Static Tube technology. It is a multi-functional sensor. It can replace thermally heated instruments, where power requirements are high. Gives easy access to duct measurement compared to a standard Pitot Tube. For example, in ceilings voids and confined areas, where there is a thick lagging or metal cladding.
-
Product
Low Noise Amplifier
1010
-
A low noise, DC-coupled amplifier is packaged in a rugged, die-cast aluminum case with BNC connectors enabling input and output. Provides very low voltage noise and current noise in the critical region of 0.1 Hz to 10 Hz making this the ideal amplifier for thermopile detectors in sensitive systems design and laboratory experiments.
-
Product
Millimeter Wave Control Devices
-
Ducommun millimeter wave products include various control devices for system integration. The CAE, CPS, CPD and CPM series control devices are discrete or MMIC based PIN diode attenuators and switches. The CAF, CAL, CAR and CPL series control devices are waveguide based mechanical tunable attenuators and phase shifters. These devices are offered to cover the frequency range from 18 GHz to 110 GHz.
-
Product
Portable Power Amplifier
PA30Bip-H
-
PA30Bip-H portable power amplifier is designed with linear amplifier principle. It is very light portable solution with three channels of current output and four channels of voltage output.
-
Product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
-
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
High voltage amplifiers (to ±500V)
-
These amplifiers provide high amplitudes and bandwidths, and are well suited for use as booster amplifiers for lower-voltage arbitrary waveform generators.
-
Product
Power Amplifier For Real-Time Dynamic Simulation(RTDS) Application
-
As the first power amplifier manufacturer in China, PONOVO has been offering various power amplifier products for customers in China and other countries since 2001. PONOVO has launched both conventional power amplifier for power system use and also 4-Quadrant power amplifier for more filed application, such as microgrid, windfarm, PV, HVDC, areospace, battery simulation, etc.
-
Product
CATV Amplifiers
-
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of single-ended and differential 75 Ω broadband amplifiers service head-end, HFC infrastructure Nodes, system and line-extender amplifies, EQAM and CPE applications. MACOM’s industry leading GaAs amplifiers are offered in a range of small, plastic leaded and leadless packages operating off standard voltage rails 5,8 & 12V. Covering reverse path, 5 – 300MHz, and forward path, 45 – 1800MHz, our amplifiers offer flat gain response, low distortion and high linearity.
-
Product
Broadband Power Amplifiers
-
Our range of broadband power amplifiers are designed using the most suitable devices and techniques. We don’t believe in following fashion in our choice of parts, but will continue to use older technology where it is still the best, and incorporate the new where improvements can be made.
-
Product
Reference plus Comparator or Amplifier
-
Analog Devices reference plus comparator or amplifier products combine the excellent initial accuracy and low overtemperature drift performance of single function voltage references with comparators, buffer amplifiers, and current sense amplifiers. These products offer compact solutions for a broad range of applications such as battery monitoring, threshold detectors, window comparators, auto power-off circuits, and low dropout (LDO) regulators.
-
Product
Wideband GaN Amplifiers
-
The Teledyne RF & Microwave family of GaN-based amplifiers maximizes power density and efficiency, and establishes a new benchmark for small size in the 0.1 to 6.0 GHz range that operates over multi octave. With dimensions of 2.5"L x 2"W x 0.42"H at only 2.1 cubic inches, these modular, non-ITAR GaN amplifiers maintain the rugged design characteristics needed for harsh airborne and land based requirements.
-
Product
Composite 1×24 Video Distribution Amplifier Board
BL-VDA124-01
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Power Operational Amplifiers
-
ST offers a portfolio of power op-amps characterized for high output current, low drop and high gain. This makes them suitable for a wide range of applications and, in particular, for driving inductive loads such as motors and lamps, as well as in automotive applications offering superior performances. Our op-amps are available in insertion and surface-mount packages to meet different environmental requirements.
-
Product
Crossed-Roller Bearing Linear Stage ,25mm Travel XYZ,Sensitivity 1um
NFP-3462
-
Model:NFP-3462 Crossed-Roller Bearing Linear Stage ,25mm Travel XYZ,Sensitivity 1um Details&Spec: Please refer to NFP-1462 Specification,It is combinated by 2pcs NFP-1462(C,SR,SL) and 1pc NFP-1462CZ(as vertcail stage)
-
Product
Solid-State RF amplifier module for High Power Testing
-
Exodus Advanced Communications
Exodus introduces the AMP1071 - a Solid-State RF amplifier module covering the entire ultra-wide 2.0-20.0GHz frequency range instantaneously at 20W CW minimum. Using State of the Art GaN devices, the AMP1071 operates from a 32VDC source at less than 10A consumption. This module is suitable for use with all single channel modulation standards and applications requiring high power and ultra-wide band coverage. It has built-in protection circuits, high reliability and ruggedness. Typical applications include High Power Testing, EMI/RFI, EW and Communications and Jamming.
-
Product
Amplifier Modules Broadband
-
Modules are usually smaller and are usually part of systems. You supply your own DC voltage, make the connections and supply your own DC supply. Modules are available with or without heatsinks and fans. Amplifiers Modules are available in both Broadband and Band-Specific frequencies. Modular design concepts save time and money, and are lightweight, reliable, cost-effective solutions. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project. Please refer to our Adapted & Custom Design Solutions link to begin formulating your performance objectives and other criteria.
-
Product
RF High Power Broadband Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Broadband amplifiers of KeyLink have exceptional RF and Microwave performance. These RF broadband amplifiers(wideband amplifiers) are available in wide frequency bands from 1 MHz to 18 GHz. Power levels for octave and multi-octave designs range from 1 watts to over 1000 watts. Applications of these broadband RF amplifiers range from radar, jamming, communication to test and measurement.
-
Product
MOSFETs For Amplifier
-
These are enhanced power MOSFETs with excellent frequency characteristics. They are ideal for audio amplifier output.
-
Product
Shortwave Power Amplifier
OM4001A
-
The OM Power model OM4001A is designed for all short wave amateur bands from 1.8 to 29.7 MHz (including WARC bands) and all modes. It is equipped with a two ceramic tetrodes FU-728F.
-
Product
Distribution Amplifiers
-
The Quartzlock range of distribution amplifiers are intended for use when multiple outputs from a single frequency standard/generator are required. This may be encountered in engineering labs, national standards labs, research and development, calibration labs and production. This is vital for the distribution of signals from other precision frequency standards like Hydrogen Masers, Cesium oscillators. For a technical discussion about distribution amplifiers go here or select a product range below.
-
Product
SW Range Broadband Power Amplifiers 0.8 GHZ - 4 GHZ
SW Series
-
Class A solid stateBroadband (instantaneous single band): 0.8 GHz 4 GHzTypical output power : 18 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 13 W and H < -20 dBc up to 2.5 GHz andP1dB > 12 W and H < -20 dBc from 2.5 GHz to 4 GHzAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
Product
Guided Wave Radar Level Transmitters
LWT Series
-
For high-accuracy, reliable measurements even in harsh conditions.Using radar frequencies, guided in a probe going into the monitored vessel, guided-wave radar level measurement provides continuous, reliable measurements with high accuracy. The radar wave being guided by the probe, the wave energy remains high which allows measurement even in harsh conditions.
-
Product
Variable Gain Amplifier
VGA
-
RF Lambda’s variable gain amplifiers (VGA) are standard amplifiers which include a gain control pin to allow the customer to tune the gain for various applications without sacrificing performance and eliminating the need to use a separate amplifier and attenuator. Hermetically Sealed options are available upon request.
-
Product
Low Noise Amplifier
LNA
-
Teledyne Defence & Space (TDS) Low Noise Amplfiers (LNA) are designed to amplify very low power signals without degrading the signal-to-noise ratio.An amplifiers is designed to increase the power of both the signal and the noise however the Low Noise Amplifier is specifically designed to minimise the additional noise so important information should not be lost.
-
Product
High Voltage, High Current Linear Amplifier
P100
-
The P100 is a general purpose linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±50V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device.
-
Product
Single Channel High Voltage Linear Amplifier
A400
-
The A400 is a general purpose broadband linear amplifier having a fixed amplification of 20 times and capable of bipolar high voltage output of 200. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to 10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
-
Product
Portable Power Amplifier
PAC60Cip
-
PAC60Cip is the portable conventional linear power amplifier model with six channels of current output. It is with 6*30A/210VA output, and this current amplifier is similar to PAC60Ci but it has lower output power and less weight.
-
Product
Power Amplifiers
-
Power Amplifier is used to amplify the output of the CS700A or CS701 signal generators. The 52 MHz bandwidth amplifier can swing 36Vpp with an output current up to 1A continuous. The CS1070 includes an internal inverting power supply to provide the negative rail, simplifying power supply requirements. The gain is fixed at x10 (20dB). The output voltage range is ±5V to ±18V and asymmetrical to +31, -5V for PSRR measurements right up to 30V as the input supply increases past 20V.
