ADC
quantization of an analog signal into a digital signal.
See Also: Analog-to-Digital Converters, FPGA, Transducers
-
product
8-bit Digitizers
ADC6000
Guzik AXIe ADC 6000 Series Digital Acquisition and Processing Modules combine high-speed waveform digitizer with built-in digital signal processing hardware, which enables mixed-domain signal capture and analysis with high-speed data transfer link to a computer. The ADC 6000 Modules come in a space-saving display-less 1U 19” AXIe modular form factor.
-
product
Compressed Air RH+T Transmitter
T3419P
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
Interface
Interface devices convert one type of control signal to another, saving time and money by extending the life of existing field devices. Please see our Interface Matrix to assist in choosing the correct product.
-
product
PCI Express Ultra-fast Data Acquisition Add-In Cards
Ultraview's PCIe series of data acquisition add-in cards are complete A/D systems on a single PCIe add-in card. These boards incorporate up to 8GB of on-board RAM with up to 7GB/sec on Kintex 7 (up to 1.4GB/sec on Virtex 5) typical PCIe bus transfer rates enabling full-rate acquisition for long durations. All boards in the PCIe series are supported with the same user software allowing users to select the bit resolution and acquisition rate appropriate for a given application and then easily re-use the same software on a different part. Included with each card are graphical waveform viewers, example user software with source code included, and device drivers for Linux and Windows. The example software is intended to allow users to quickly prototype and develop their applications.
-
product
6-Channel 200 MHz A/D and 4-Channel 800 MHz D/A with Virtex-7 FPGA - 6U VPX
Model 58720
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Three or six 200 MHz 16-bit A/Ds- One or two DUCs (Digital Upconverters)- Two or four 800 MHz 16-bit D/As- 4 or 8 GB of DDR3 SDRAM Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connectionsto the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Multi-Layer Network Test Platform
From fiber installation to service deployment, these platforms are designed to maximize network performance and accelerate the deployment of new services. Critical network parameters and performance can be monitored and network impairments quickly identified to accelerate the deployment of new services. A modular design with different size bay adapters allows you to customize your test set as needed adding further value.
-
product
Advanced Thermal Imaging Camera
FLIR E54
The FLIR E54 is your entry into the Exx-Series, offering the resolution and sensitivity you need for basic condition monitoring, electrical/mechanical inspection, and building inspection. The 320 × 240 pixel thermal detector accurately measures temperatures up to 650°C (1202°F) and produces crisp, vibrant imagery that can be enhanced with patented FLIR MSX® technology for added detail and perspective. The onboard FLIR Inspection Route runs pre-planned routes to help you stay organized when surveying large or multiple locations. FLIR Ignite provides automatic uploading of E54 images directly from the camera to the cloud for easy, secure storage and sharing.
-
product
Programmable Selsyn Indicators
PSI
Computer Conversions Corporation
Computer Conversions Solid State Selsyn/Resolver Indicator digitizes the outputs of Selsyns, Synchros and Resolvers for position indication and control applications. The Selsyn Indicator is designed to replace failure prone mechanical selsyn torque receivers, counters, etc. The tracking converters high noise immunity and high speed tracking characteristics make it ideal for use in industrial envrionments.
-
product
High-Speed Digitizers and FPGA Development Kit
Keysight unique technology uses proprietary ICs so you can get the most out of the ADCs and FPGAs integrated into the digitizer. On-board real-time algorithm in the FPGA allows fast detection of signal characteristics in various domains.
-
product
Modular DC Electronic Load
63600
Chroma Systems Solutions, Inc.
Chroma’s 63600 Modular DC Electronic Load is designed for testing multi-output AC/DC power supplies, DC/DC converters, chargers, batteries, adapters, and power electronic components. They are excellent for use in research, development, production, and incoming inspection applications. The 63600’s state-of-the-art design uses DSP technology to simulate non-linear loads using an unique CZ operation mode allowing realistic loading behavior.
-
product
Group3 Control
Group3 Control is a fiber optically linked control system using distributed I/O modules called Device Interfaces, or DIs. A DI is positioned at the point to be controlled and the appropriate I/O boards added to it from the list below.
-
product
PCI Express Expansion Backplane
SKU-076-0X
PCI Express Expansion backplane was designed as a universal solution for Desktop or Laptop host computer expansion. It allows adding up to four additional PCI Express boards to the host computer. Expansion backplane can be placed inside any general-purpose computer chassis, and connects to the host computer via 5ft (or 10ft) CAT6 cable.
-
product
8-Channel ADC Module
FMC108
Sundance Multiprocessor Technology Ltd.
The FMC108 is an eight-channel ADC FMC (FPGA Mezzanine Card) which is fully compliant with the VITA 57.1-2010 standard. The FMC108 card provides eight A/D 14-bit 250MSPS channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available. The FMC108 has the HPC (high-pin count) connector, front panel I/O, and is conduction cooled compliant. The board is also available with Mil-I-46058c compliant Conformal Coating.
-
product
DC-DC Converters
Electronic Test & Power Systems
The standard range of DC-DC Converters contains units with power outputs from 40W to 5kW. Small footprints, high conversion efficiencies and floating outputs are common throughout the converter range.
-
product
PXIe 16 Bit High Speed Digitizer - 250 MS/s on 4 Channels
M4X.4421-X4
The M4x.44xx-x4 series digitizers deliver the highest performance in both speed and resolution. The series includes PCIe cards with either two or four synchronous channels where each channel has its own dedicated ADC. The ADC’s can sample at rates from 130 MS/s up to 500 MS/s and are available with either 14 bit or 16 bit resolution. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high quality signal acquisition.
-
product
32-CH 12-Bit 100 kS/s Isolated Analog Input Card
PCI-9113A
ADLINK PCI-9113A is a 32-CH, 12-bit, 100 kS/s isolated analog input card. The PCI-9113A provides analog inputs with 3 programmable input ranges for both bipolar and unipolar inputs. The 32-CH single-ended analog inputs can be converted to 16-CH differential analog inputs, which improve the noise rejection in harsh industrial environments. The analog inputs are isolated from the PC's system ground. This feature not only protects the PC from being damaged from surges on the signal lines, but also eliminates ground loops and common-mode problems commonly seen in industrial measurement applications. The PCI-9113A provides custom circuit area for input signal conditioning. Either signal attenuation or filtering can be applied on per channel basis. With all the features, ADLINK PCI-9113A delivers cost-effective and reliable data acquisition capabilities for ATE, sensor monitoring, data logging, power transmission, and a broad variety of industrial measurement applications.
-
product
Data Acquisition - 3U 3-Slot
DAQ-33CP0G
is a preconfigured rugged system with a high-performance, low power ARM® Cortex®-A9 processor. It is ideally suited to support a multitude of military/aerospace data acquisition applications that require high-density, multichannel programmable ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (2.0 A&B or J1939); A/D Conversion; RTD Measurement; RS-232/422/485 Serial Communications Dual-Port Gig-E Ethernet.
-
product
Low Noise Test Cables For N1413 With B2980 Series, 1.5 M
N1427A
The N1427A is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It comes with a separate triaxial (special screw-type) female connector and a High Voltage BNC (special type) female connector. This allows terminal configuration to be converted to any other configuration. Therefore, custom test fixture can easily be constructed. The N1413A High Resistance Meter Fixture Adapter is also required to connect the N1427A to the B2985B/87B.
-
product
Autotransformer
T-1007
The Titan Series T-1007 Auto-transformer is used to conveniently scale the standard OV to 130V / 260V full scale Titan AC Power Source/Frequency Converter output to either X .5 stepdown (OV to 65V) or X2 stepup (OV to 520V). It has a 1.2 KVA power rating with excellent bandwidth and voltage regulation.The unit is of toroidal design, making it approximately half the size and weight of a comparable stacked laminate transformer. It is center filled with epoxy for isolation and durability, and features simple 1/4" bolt center mounting.
-
product
Infiniium S-Series High-Definition Oscilloscope: 6 GHz, 4 Analog Plus 16 Digital Channels
MSOS604A
6 GHz bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 6.8 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15" capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
product
Dynamic Signal Analyser
Dynamic signal analyzers provide highly accurate measurement and analysis, and are widely used in audio testing, acoustic measurement, environmental noise testing, vibration analysis, NVH measurement, machine condition monitoring, and rotating machinery evaluation. ADLINK's dynamic signal analyzer series features 24-bit analog-to-digital converters (ADCs) with sampling rates up to 432 kS/s for PXI, PCI, and USB platforms for flexible yet accurate measurement supporting high performance and cost-effectiveness in a wide variety of testing applications.
-
product
8-Channel 200 MHz, 16-bit A/D with Virtex-7 FPGA - 6U VPX
Model 58760
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four or eight 200 MHz 16-bit A/Ds- 4 or 8 GB of DDR3 SDRAM- PCI Express (Gen. 1, 2 & 3) interface up to x8- Sample clock synchronization to an external system reference LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Temperature and Humidity Probe
T0211-4
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
AXIe Products
The AXIe is an open standard, that leverages from existing standards from ATCA, PXI, LXI and IVI, with high performance per rack inch and added features including timing, triggering, and module-to-module data movement features that are important to the implementation of high-performance test and measurement systems.
-
product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 5 GS/s on 5 Channels, 2.5 GS/s on 10 Channels, 1.25 GS/s on 20 Channels
DN6.225-20
The digitizerNETBOX DN6.22x series allows recording of up to 24 channels with sampling rates of up to 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
product
OnyxFX FlexorSet 2-Ch. 3.0 GHz A/D, 2-Ch. 2.8 GHz D/A - PCIe
Model 7070-320
The FlexorTM Model 3320 is a multichannel, high-speed data converter FMC.It is suitable for connection to RF or IF ports of a communications or radar system. It includes two 3.0 GHz A/Ds, two 2.8 GHz D/As, programmable clocking and multiboard synchronization for support of larger high-channel count-systems.
-
product
Thermal Shroud
BC8-55/150C
When combined with a thermal conditioner such as the Bemco PCL3L-III or PCL3M-III, this shroud converts a 24 inch inside diameter by 30 inch high vacuum only vertical bell jar into a 19 inch inside diameter by 20 inch high thermal vacuum testing system. With a convenient clam shell door, test objects are easily loaded by simply raising the bell jar above the top of the door opening.
-
product
Analog Power Modules
Renesas' family of analog power modules offers users a fully integrated DC/DC switching buck converter in one package. These modules combine the controller, power FETs, output inductor, and compensation circuitry in a single package minimizing both the external component count and complexity of converter design.
-
product
12 A/D Channels (±25mA FSR); 24-bit Sigma-Delta
AD3
Module AD3 features 12 channels with up to 24-bit Sigma-Delta A/D converters for each individual channel. The maximum programmable, expected full-scale range input for the AD3 module is ±25 mA respectively. The A/D converters have programmable sample rates of up to 256 kHz.
-
product
6-Channel 200 MHz A/D and 4-Channel 800 MHz D/A with Virtex-6 FPGA - 6U VPX
Model 58620
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Six 200 MHz 16-bit A/Ds- Two DUC (digital upconverters)- Four 800 MHz 16-bit D/As- 4 GB of DDR3 SDRAM; 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
