Test Program Set Development
provides set of UUT specific documentation, programming and interface.
-
product
COM Express Type 10 Starter Kit Plus
COM Express Type 10 Starter Kit Plus
The COM Express Type 10 nanoX Starter Kit Plus consists of a COM Express Type 10 core module reference carrier board that provides two PCIe Mini Card slots, 2 RJ-45 LAN ports, 2x USB 3.0, 2x USB 2.0, 1x USB client, 2x DB-9 COM, 1x SD card socket, and Mic/Linein/ Line-out. ADLINK also provides additional development tools including a verified 10.1" LVDS panel (optional), power supply, thermal solution and cabling accessories.
-
product
MASTER FUEL PRESSURE TEST SET
FPT5000
*Quickly and easily diagnose fuel-related issues on most major gasoline engine platforms, including domestic and foreign vehicles*In-line adapter configuration allows for easier connection to the fuel system as well as the ability to isolate the supply and return lines independently without disconnecting the adapters from the engine*3-1/2" gauge and hose configuration allows adapters to connect directly to the gauge and bleed-off or connect to the 48" extension hose for applications where additional reach is necessary
-
product
Test Leads Adapter Sets
A physical device used to connect electronic test equipment to a device under test.
-
product
Vacuum Interrupter Test Set
HTZK-IV / 385
Wuhan Huatian Electric Power Automation Co., Ltd.
Quantitative measurement, suitable for vacuum switch vacuum measurement, vacuum switch preventive detection special instrument.
-
product
Primary Injection Test Set
PI-6000
The PI-6000 is a rugged & durable primary injection test set capable of testing circuit breakers up to 6,000 amperes frame size. It incorporates an output transformer with dual primaries to facilitate its use on power sources of 480 VAC as well as 208-240 VAC. The unit also includes dual secondaries to provide optimal impedance matching to a wide range of circuit breaker sizes. An internal voltage sensor automatically configures the AC control power section to be energized only when properly configured for the applied voltage.
-
product
Eclipse Test Development Environment
The Eclipse Test Development Environment automatically creates tests that are used to bring up new products in the lab. Failures can be quickly debugged using software tools such as the Eclipse Timing Diagram Analyzer and the Schematic Logic Probe.
-
product
Switching Test Set
U3020AS26
The Keysight U3020AS26 is a switch matrix that consists of two single-pole-six-throw (SP6T) switches. It allows switching of multiple signal paths without physically changing the connections. This allows multiple tests to be performed with the same setup, eliminating the need for frequent connects and disconnects. An entire testing process can be automated, increasing the throughput in high-volume production environments.
-
product
High Voltage Test Set
Hi-Pot Series
SCOPE introduces a high voltage test set, these high voltage testing sets comes with Power frequency AC high voltage /DC high Voltage test /AC-DC high Voltage test set for testing transformers, motors, insulators, cables etc. Further, these testing sets are capable of giving continuously variable HIGH VOLTAGE from zero to maximum rated output voltage. Wide range of up to 100 kV is available in user selectable combinations.
-
product
Lens Module Test Platform
The Lens Module Test Platform is a flexible solution to deliver the quality that is expected from your brand for all types of lenses and cameras. The system can be configured to measure objective, eyepiece or camera lenses. As the platform can efficiently measure lenses as small as 2 mm3, it is perfect for the critically precise applications of life sciences, consumer electronics, automotive and other industries. With 25+ years of quality experience, the Lens Module Test Platform ensures that all products shipped to market work as intended.
-
product
Milli Volt Drop Test Set
Widely used for testing transformer and switchgear, this equipment is available to clients in different capacities.
-
product
Advanced SoC/Analog Test System
3650-EX
Chroma 3650-EX is specifically designed for high-throughput and high parallel test capabilities to provide the most cost effective solution for fabless, IDM and testing houses.
-
product
Four-module test set
F8200
Use the F8200 Power System Simulator for testing single-phase conventional schemes, digital protection systems, and more. This four-module F8000-series instrument is available in four standard configurations of HVA Current, HVA Voltage, and Low-Density Logic I/O modules.
-
product
Three-Phase Relay Test Set
CMC 353
With its compact design and low weight of 13.3 kg / 29.3 lbs, the CMC 353 provides the perfect combination of portability and power. It is the ideal test set for three-phase protection testing and the commissioning of SCADA systems. The powerful current outputs (3 x 32 A / 430 VA) optimally support 5 A relay testing.
-
product
Conductor Damage Test Set
CD-2M
Is designed to carry out tests specified for Switches used for Domestic and similar applications as included under IS:3854:1997. It is used to ensure that Screwtype terminals of switches are such that they clamp the conductor without causing undue damage to the conductor strands. It is a compact and robust andequipment housed in a bench top enclosure. The CD-2M is motorized to allow easy operation. The Instrument is designed to meet the requirements of IS:3854:1997 and other related specifications.
-
product
Test Program Modules
The BRAT Test Program developed will provide functional validation of an assembly based on customer supplied documentation. This does not include hardware (e.g., Interface Test Adaptors), documentation (e.g., technical orders), travel or travel related per diem, or site verification test or installation.
-
product
Phantom Load Test Set
Is a testing accessory, wisely designed for field testing service. This equipment helps in providing artificial load that is unaltered by the change in power supply.
-
product
Quad Optical Loss Test Set
KI27624-INGAAS-APC
A Quad Optical Loss Test Set used to test power, insertion loss, continuity and faults on multimode and single mode fiber with an APC connector at 850 / 1300 nm & 1310 / 1550 nm. In a small package, it provides a powerful solution to improve test flexibility and productivity.
-
product
Development Test for Electric Motors with Power Electronics
Test bench for electric machines and inverters in hybrid applications*Control of mechanical parameters*Verification of electrical properties*Checking the LL characteristics*Short circuit measurement*Recording the performance process*Noise measurement*Temperature measurement
-
product
NI Vehicle Radar Test System
VRTS provides automated radar measurement and obstacle simulation capabilities for 76 to 81 GHz automotive radar systems. With VRTS, you can perform precision RF measurements and simulate a wide range of test scenarios for radar hardware and software subsystems, including sensors, advanced driver assistance systems (ADAS), and embedded software. Use VRTS for all phases, from design to manufacturing, of ADAS and radar system test.
-
product
Robotic and Computer Programming System
Sense
Sense is a robotic and computer programming system which allows users to explore, problem solve, and advance their computer programming abilities from just starting in visual block programming, to Python and C languages.
-
product
Multibus Development and Test Tool for ECUs and Networks
CANoe
The versatile software tool for development, testing and analysis of ECUs and entire networks. Bus systems: CAN, CAN FD, LIN, MOST, FlexRay, Ethernet, WLAN, Car2x ITS G5, AFDX, J1708, ARINC429 > Protocols: TCP/IP, SOME/IP, CANopen, J1939, ISO 11783, J1587, MCnet, GMLAN, K-Line, CANaerospace and ARINC 825. Others upon request.
-
product
Two-Way Optical Loss Test Set
KI23427OLF-INGAAS-APC
A Two-Way Optical Loss Test set (OLTS) that's perfect for medium to ultra high fiber count loss, length and optical return loss testing applications on single mode fiber with an APC connector at triple 1310 / 1490 / 1550 nm. A pair of these compact instruments set new standards of productivity, accuracy and ease of use. The 650 nm VFL is on a separate port.
-
product
Vacuum Interrupter Pressure Integrity Test Set
Low Drift Current is measured by applying magnetic field.
-
product
Radio Frequency, Communications, & Navigation Test Systems
Reduce testing time and costs with the Astronics radio test sets for use in military, avionics, and civil security industries.Available in commercial and military grades, these integrated test systems make it easy to develop test program sets and leverage them securely and instantly across all deployed testers at the factory, depot, and operational levels.
-
product
Wireless Device Test Sets & Wireless Solutions
Keysight products provide mobile phone designers and manufacturers with increased measurement speeds, improved accuracy, and exceptional flexibility for testing mobile devices. Our one box test sets cover all the major technology formats: LTE-Advanced, LTE (FDD and TDD), GSM/GPRS/EGPRS/E-EDGE, W-CDMA/HSPA/HSPA+/DC-HSDPA, cdma2000®/1xEV-DO/eHRPD, TD-SCDMA/TD-HSDPA/TD-HSUPA, IS-95, TIA/EIA-136, AMPS, Bluetooth®, Bluetooth Enhanced Data Rate (EDR), Bluetooth Low Energy, ZigBee™, Wireless LAN (WLAN), 802.11a/b/g, 802.11n, NFC/EMV, MIMO, and WiMAX™.
-
product
OTP-Based Test System
Power electronics assemblies often cannot be tested using conventional technology for their electrical performance. Due to the adaptability of the instrumentation, the OTP concept offers an ideal platform even beyond the space requirements of several control cabinets. In order to achieve high test flexibility with different assemblies, the system was equipped with three-phase AC sources and AC loads as well as a precise three-phase power meter. DC sources and loads with different current and voltage ranges cover the test of frequent DUT operating parameters. Time-dependent voltage or current signals can be stimulated by an arbitrary generator with power amplifier. General measurements such as current, voltage, frequency, resistance can be carried out flexibly at various test points using the matrix concept. An oscilloscope with RF multiplexer is available for high-frequency measurements such as residual ripple, switching processes, etc.
-
product
Secondary Injection Test Set
PTE-100-C
The PTE-100-C is a portable Universal test equipment for testing electromechanical, electronic, and digital relays. The equipment can output a variable current up to 250A, a variable AC Voltage up to 250V, a variable DC Voltage up to 350V. Also the unit incorporates a variable stabilized auxiliary DC Voltage supply up to 250V and a fixed AC Voltage output up to 110V, which can be variable with the PTE-FCF option.
-
product
AC/DC Hipot Test Set (Gas Type)
YDQ / 570
Wuhan Huatian Electric Power Automation Co., Ltd.
Necessary test equipment for power equipment inspection and preventive test.
-
product
Compliance Test, Development and Test Service
DinoStor
With its focus on solving critical backup problems associated with Network-Attached Storage (NAS), DinoStor delivers a broad range of products and services to benefit users and vendors of NAS solutions.
-
product
Programable DC Power Supply
ADG-L Series
14 models and three different output power, 4kW, 8 kW and 12 kW. Utilizing PWM technology, ADG-L delivers stable output and precise measurement. With CV, CC and CP mode, ADG-L series is ideal for Photovoltaic, Electric Vehicle, battery, fuse/capacitor and third party laboratory testing.
