-
Product
Automation Of Vibration Testing
-
The system can be equipped with various National I / O devices using PCI, PXI, USB and cRIO platforms for both testing tasks and for advanced diagnostics of the tested products. The system software includes a wide range of virtual instruments (Vibrotest, Vibration, Vibrotest SBC, Vibrorezonans, Beat, etc.).
-
Product
Ethernet To Parallel Digital Interface Boards
-
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
-
Product
RS LabSite® modulogic
-
RS LabSite® modulogic is a comprehensive and adaptable software suite conceived for introducing service loads into individual components or complete vehicles, or performing calculations within the framework of Virtual Prototyping (standardized loadsequences, virtual generation of load data). This enables you to stay in full control of all tasks that follow the acquisition of measurement data in the proving ground.
-
Product
General Purpose Switches
SMX-5XXX (General Purpose)
General Purpose Switch
The VTI SMX-5xxx Series of general purpose switches deliver exceptional performance and reliability by implementing extensive signal path shielding, isolation and built-in health monitoring. Embedded virtual schematic control simplifies setup and debugging, allowing all relays to be engaged independent of application software and device drivers.Ideally suited for a wide range of discrete signal switching, the SMX-5xxx Series provides uncompromised measurement integrity ideal for the most demanding aerospace, defense and automotive automated test equipment (ATE) applications.
-
Product
UV Fluorescence Sulfur Dioxide Analyzer
Model T100
-
The Model T100 uses the proven UV fluorescence principle, coupled with a state of the art user interface to provide easy, accurate, and dependable measurements of low level SO2.Exceptional stability is achieved with the use of an optical shutter to compensate for PMT drift and a reference detector to correct for changes in UV lamp intensity. A hydrocarbon ‘kicker’ and advanced optical design combine to prevent inaccuracies due to interferents.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel using NumaView™ Software, or via RS232, Ethernet, or USB com ports, either locally or by remote connection using the included NumaView™ Remote PC Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.The Model T100 comes with NumaView ™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView ™ Software.
-
Product
MIMIC® Redfish Simulator
-
The MIMIC Redfish Simulator, the industry's first integrated simulation tool supporting Redfish, allows developers to perform real world, integrated device simulations. MIMIC simulates thousands of Redfish-capable devices. MIMIC allows suppliers of Redfish devices and applications to design, develop and test their products in a virtual and scalable network environment, assuring customers that their applications will be able to handle the scales of messages and different types of requests to work properly when deployed across heterogeneous environments.
-
Product
High Performance Isotope analysis of LC Separated Compounds
Iso CHROM® LC
-
Elementar Analysensysteme GmbH
Unlike the existing LC-inlet solution via chemical oxidation, the iso CHROM LC works with high-temperature combustion. It quantitatively converts organic carbon to CO2.In addition, the easy-to-use iso CHROM LC shows outstanding precision, accuracy, and linearity without significant peak broadening that can diminish the chromatographic performance. In continuous operation, virtually all peaks in a chromatogram can be analyzed for the stable isotope ratios of carbon.
-
Product
Quadrature Signal Generator
TE5100-PCI
-
The TE5100 is a 100MHz Direct Digital Synthesized Signal Generator available in a 3U, CompactPCI or straight PCI format. The TE5100 generates Sine and ACMOS/TTL output signals simultaneously up to 100MHz in 1 µHz steps. Sweep, FSK, Chirp and Single Tone are generated on board. The virtual panel allows control up to 100MHz of all parameters. The TE5100 is equipped with a ±1ppm on-board TCXO clock and can accept an external clock source.
-
Product
Explosion Proof Paramagnetic Oxygen Analyzer
Model 3020M
-
Teledyne Analytical Instruments
The Model 3020P is a versatile microprocessor-based instrument specifically designed to detect oxygen in a variety of gases. It is a precise, cost effective instrument capable of measuring percent oxygen in as low as the 0-1% range. Drawing on the solid performance of the 3000 series control platform, the 3020M provides the user with a wide variety of features and options to satisfy virtually any application.
-
Product
USB Oscilloscope, Logic Analyzer and Variable Power Supply
Analog Discovery 2
-
Digilent Analog Discovery 2, developed in conjunction with Analog Devices and supported by Xilinx University Program, is a multi-function instrument that allows users to measure, visualize, generate, record, and control mixed signal circuits of all kinds. The low-cost Analog Discovery 2 is small enough to fit in your pocket, but powerful enough to replace a stack of lab equipment, providing engineering students, hobbyists, and electronics enthusiasts the freedom to work with analog and digital circuits in virtually any environment, in or out of the lab. The analog and digital inputs and outputs can be connected to a circuit using simple wire probes; alternatively, the Analog Discovery BNC Adapter and BNC probes can be used to connect and utilize the inputs and outputs. Driven by the free WaveForms 2015 (Mac, Linux and Windows Compatible) software, Analog Discovery 2 can be configured to work as any one of several traditional instruments.
-
Product
Precision IV Analyzer / 8 Slot Precision Measurement Mainframe
E5270B
Mainframe
Keysight E5270B Precision IV Analyzer is the complete solution for current-voltage characterization of a wide range of materials and devices. The E5270B supports multiple SMUs (Source/Monitor Units) for voltage/current sourcing and voltage/current measurement with the best in the class current measurement performance as low as 0.1 fA. Its modular architecture allows you to configure or upgrade SMU modules for available eight slots. The EasyEXPERT group+ GUI based characterization software is furnished and available on your PC to support all the tasks required in the characterization from the measurement setup to the data analysis. Powerful integration of SMU's versatile measurement capabilities and GUI based characterization software makes the E5270B the best solution for characterization and evaluation of devices, materials, semiconductors, active/passive components, or virtually any other type of electronic device with uncompromised measurement reliability and efficiency.
-
Product
Data Record Adaptor and Correlator
Joiner
-
nTh Network Technologies to Help
Joiner is a data record adaptor and correlator for mobile and core networks management. The ideal partner for big data architectures with data lakes and analytic applications. Distributed as Docker component, it may be orchestrated in line with the network virtualization function concepts.
-
Product
SAR Testing
-
RF transmitters used in close proximity to the human body must be evaluated against human Exposure standards which set basic restrictions for the Specific Absorption Rate (SAR) of RF energy by any part of the human body. This may include two-way radios, cellular phones, smartphones, spread spectrum, Bluetooth devices, wireless EFTPOS terminals and WLAN devices used in PDA/notebook/laptop/tablet computers. In Australia and Europe, virtually all devices exceeding the power threshold of 20mW (13dBm) and used in close proximity to the human body must comply with SAR requirements. There is no such blanket exemption in the USA and Canada where each product must be assessed against frequency/power level criteria.
-
Product
Mid-Range Gas Filter Correlation Carbon Dioxide Analyzer
Model T360M
-
The Model T360M CO2 analyzer measures Carbon Dioxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high-energy IR light source is alternately passed through a CO2 filled chamber and a chamber with no CO2 present. The light path then travels through the sample cell, which has a folded path of 1.28 meters.The energy loss through the sample cell is compared with the reference signal provided by the filter wheel to produce a signal proportional to concentration, with little effect from interfering gases within the sample. This design produces excellent zero and span stability and high signal to noise ratio, allowing excellent performance over a wide concentration range, making this instrument an ideal choice for CO2 reporting requirements associated with dilution CEMS.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T360M comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
Network Function Virtualization and Software Defined Network
NFV and SDN
-
Network Function Virtualization (NFV) is a concept closely-related to software defined networking (SDN) whereby certain aspects of network operations (routing for example) are de-coupled from hardware and delivered as a software-only product or service. The software solutions sometimes called Virtual Machine (VM) Software Editions. Network operators, service providers, and enterprise network administrators can employ Virtualized Network Functions (VNF) to accelerate deployment of network services, cut capital expenses and reduce operating costs.
-
Product
Networks
-
Our products include wireless network solutions, mobile ad hoc networks, provisioned applications and virtualized environments networking; interference-resistant technologies and satellites. Our RF-based systems give customers a pivotal advantage in today's complex network environments. We transfer concepts into reality, enabling fast, reliable delivery of information and intelligence to individual terminals while ensuring interoperability across vast, dynamic networks.
-
Product
Field Testing & Verification Services
-
TMD can assist your utility with virtually any metering-related product or service, and one of the most impactful services we provide is our field testing services.
-
Product
Vision Sensor
In-Sight 2000 Series
-
The new In-Sight 2000 solves simple error-proofing applications and sets new standards for value, ease-of-use, and flexibility. The In-Sight 2000 is the first vision sensor that combines: Powerful In-Sight vision toolsproven In-Sight tools that ensure reliable inspection performance in a single setup environment. Easy setup with EasyBuilderintuitive point-and-click setup interface. Field interchangeable lighting and opticseasily adapts to virtually any production line environment without the need for external lights. Modular body designconfigurable in-line or right-angle mounting provides maximum flexibility in tight spaces.
-
Product
Satellite Phone Interception Solutions
-
Satellite Phone (GMPCS-Global Mobile Personal Communications by Satellite) is a terminal device act like a normal mobile. Satellite phones connect to satellites orbiting around the earth. Satellite phones rely on a network of satellites that are either fixed above the Equator (Geostationary) or in Low Earth Orbit (LEO) anywhere from 500 to 1,000 miles above the earth. Satellite phones are rarely affected by violent storms and depending upon their system architecture they can work virtually anywhere in the world. The satellite phone is the best mode of communication where no cellular coverage exists. The most popular Satellite phones are from Thuraya, iridium, and Inmarsat (IsatPhone, IsatPhone Pro and IsatPhone 2).
-
Product
Vector Signal Generator
VSG25A
-
The VSG25A is a 100 MHz to 2.5 GHz vector signal generator, featuring a 12-bit I/Q baseband arbitrary waveform generator which can be clocked at virtually any frequency from 54 kHz to 180 MHz, and includes a 4096×16 bit pattern buffer for built-in or custom modulation.
-
Product
Terminations
-
With a variety of models supporting virtually all waveguide applications, CAES Waveguide Terminations provide best-in-class VSWR performance and support a variety of frequency ranges.
-
Product
Channel Emulator/Fading Simulator
-
The channel emulator/fading simulator is a measuring instrument for reproducing the actual radio wave propagation environment of mobile communication.It reproduces the fading environment defined by 3GPP and virtual environment of multiple channels such as MIMO, HetNet.It will contribute to improving development and verification efficiency of the latest mobile communication system such as 5G NR, LTE-Advanced and IoT.
-
Product
SPICE-Based Analog Simulation Program
TINA-TI
-
TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages and waveforms. TINA''s schematic capture is truly intuitive-a real "quickstart."
-
Product
High Power 90 Series Modules
-
VPC offers a wide array of modules with a variety of connection options that are configurable for virtually any interconnect requirement.
-
Product
Osprey / DX Co-Processor
9687
-
Double+ speed Osprey Co-Processor. Occupies one ISA/EISA PC slot. Writable control store, FPGA implementation of PDP-11 architecture with 4 MBytes of tightly coupled, zero wait-state memory. Includes FPJ11® compatible hardware floating point. Performance equivalent twice the DCJ-11® and 100%; of FPJ-11. On-card x86 microprocessor rapidly processes "virtual" I/O instructions. This card is used for Osprey/PC applications where all applicable I/O devices are emulated on the PC by Osprey software. Includes standard environment support for MS-DOS® V6.2.2. Windows/NT® environment support available.
-
Product
2U 19” Edge Server with Intel® Xeon® Scalable Silver/Gold Processors for 5G MEC Infrastructure Deployment
MECS-7211
MEC Server
The MECS-7211 Edge Server focuses on the edge of 5G networks to provide an open, white box platform for 5G Open RAN, private 5G networks, and a wide range of 5G MEC applications including smart cities, retail, manufacturing, autonomous vehicles, Argument Reality(AR), virtual reality(VR) and healthcare. The MECS-7211 is designed to meet stringent requirements by delivering a high level of deployment flexibility, reliability, scalability, and carrier-grade processing performance further augmented by hardware expansion. With a 450mm system depth in a small footprint 2U chassis, all I/O front access, wide operating temperature support (-5°C to +55°C), and PCIe expansion slots reserved for access to acceleration hardware such as GPU, FGPA and QAT adapters, ADLINK’s MECS-7211 is a high performance COTS platform that meets varying application and deployment requirements, and enables customers to focus on differentiating their end solutions.
-
Product
Signal Generator
-
Tektronix signal generators cover a wide range of applications, from replicating sensor signals to creating RF and the fastest high speed serial data signals. Each versatile signal generator can create a virtually unlimited number of signals - analog or digital, ideal or distorted, standard or custom. From the world's only direct synthesis of high-speed serial data waveforms for simplified receiver testing, to the world's most versatile arbitrary function generator for common stimulus signals, Tektronix has a signal generator to meet your debug challenge.
-
Product
Ultrasonic Material Thickness Gauges
MTG
-
The Elcometer Ultrasonic Material Thickness Gauges have all the features and functionality necessary for measuring material thickness and velocity on virtually any material - for a wide range of applications.
-
Product
Autosamplers
-
Teledyne has served the AA, ICP, ICP-MS, MC-ICP-MS market for over 30 years with a wide selection of autosamplers that meet virtually all laboratory needs.
-
Product
Quizix Precision Pumps
-
The variety of models within the Quizix line offers several key advantages. The wide range of flow rates, pressure configurations and available options allow Quizix pumps to meet virtually any experimental requirement from bench top to pilot scale.
