Low Noise Dual Band VCO

This custom oscillator subassembly consists of two low noise oscillators covering 1.5 to 2.5 GHz, a power combiner, a standard Teledyne RF & Microwave amplifier, and a lowpass microstrip filter. Teledyne RF & Microwave designed both oscillators for low phase noise and linear tuning. The output frequency bands are switched using standard TTL control.

Product Home Contact/Sales Company Catalog Share Add To List

Family
Related

Integrated Assemblies

Teledyne RF & Microwave

Teledyne RF & Microwave offers full first-level integration capabilities, providing not just performance components but also full subsystem solutions to help reduce program schedule and cost. Drawing on our expanding breadth of components, Teledyne RF & Microwave delivers customer-specified subsystems of analog and mixed analog-digital design, including hybrid, MMIC, and mixed hybrid-MMIC configurations. Designed to meet military or space applications, some typical subsystems Teledyne RF & Microwave delivers include I/Q demodulators, coupled detector assemblies, switched amplifier detector assemblies, and dual-band VCOs.

Product Home Contact/Sales Company Catalog Share Add To List
17 To 19 GHz QPSK Modulator

CCM19001 - Teledyne RF & Microwave

The CCM19001 is a Differential Drive Digital QPSK (Quadrature Phase Shift Keying) modulator operating across the 17.0 to 19.0 GHz frequency range. The modulator utilizes differential drive digital inputs (180º apart) to drive both of the bi-phase modulators (mixers) integrated into the assembly. The modulator is a combination of a matched pair bi-phase modulators, which are in quadrature (90º) to each other. It is modulated by switching polarities of the DC voltage controls in 4 different logic states ("0,0", "0,1", "1,0" & "1,1") for 4 phase states. The QPSK modulator provides constant amplitude, 90º vector: 0 (ref.), 90º, 180º, 270º and operates across the -55º to 85º C temperature range.

Product Home Contact/Sales Company Catalog Share Add To List
2 To 18 GHz 6 Channel Downconverter

Teledyne RF & Microwave

Teledyne RF & Micrrowave's Six Channel 2 - 18 GHz (RF and LO) downconverter operates with an IF of ~960 MHz, providing 25 dB of RF-IF gain, and bandwidth of ~500 MHz. This downconverter operates on a single LO at -6 dBm which is amplified, split, then again amplified to each of the 6 channels. Integrated into each channel is a range extension switch, controlled by a TTL input and adding 20 dB attenuation. Noise figure is ~ 13.5 dB and output IP3 is ~+25 dBm. The downconverter is 2- sided, hermetically sealed and designed for rugged applications.

Product Home Contact/Sales Company Catalog Share Add To List
Five Channel Amplifier

Teledyne RF & Microwave

Teledyne RF & Micrrowave designed the Five Channel Amplifier specifically for a custom space application. Each independent channel used dedicated RF Input/Output and DC bias connections. Each channel's RF performance was tailored differently to meet the application requirements. All components were manufactured and screened per MIL-PRF-38534, Class K. Additionally, to meet mission requirements The top assembly was also tested for RF and DC parameters during MIL-STD-202 thermal cycling and random vibration environments. This effort required disciplined development, manufacturing and program management efforts to meet challenging mechanical and RF engineering requirements.

Product Home Contact/Sales Company Catalog Share Add To List
IQ Demodulator

Teledyne RF & Microwave

Teledyne RF & Microwave IQ Demodulators are fully space-qualified designs providing stringent phase and amplitude matching, and superior output third order intercept performance. To meet high LO and IF rejection requirements diplexers are used at the I and Q ports. All components and processing fully meet MIL-PRF-38534, Class K and MIL-DTL-28837. Teledyne RF & Microwave can provide performance to meet most receiver system requirements, including single or moving LO frequencies and tight phase and amplitude matching. Customers can specify our designs for space, military, or commercial applications.

Product Home Contact/Sales Company Catalog Share Add To List
Ku Band Gain Control Amplifier

Teledyne RF & Microwave

Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.

Product Home Contact/Sales Company Catalog Share Add To List
Low Noise Triple Band Voltage Controlled Oscillator

Teledyne RF & Microwave

This Low Noise Triple Band Voltage Controlled Oscillator was designed to meet a specific customer requirement. The VCO cover the 3300 to 4700 MHz frequency range in three bands. The output power is +9 to +12 dBm with an integrated buffer amplifier to minimize load pulling. The three bands are selected using standard TTL control.

Product Home Contact/Sales Company Catalog Share Add To List
Switch Amp

Teledyne RF & Microwave

One of many potential designs, Teledyne RF & Microwave's switched amplifier covers 100 to 2000 MHz, providing 18 dB gain, phase matched to within ±1.0 degree. The primary RF input and a secondary calibration signal input are switched, then amplified, and split to two outputs. Gain balance between any of the two outputs is ± 0.5 dB. Output power at 1 dB compression is +14 dBm and input/output VSWR is 2.0:1 maximum.

Product Home Contact/Sales Company Catalog Share Add To List
Switched Amplifier With Analog Detector Output

Teledyne RF & Microwave

Operates at 3 GHz-10 to -5 dBm Input Power to +4 to +7 Output powerAnalog Detector OutputTTL Compatible, 70 dB On-to-Off Ratio, 50 ηSec Response Integrated RF Switch

Product Home Contact/Sales Company Catalog Share Add To List
Switched Limiting Amplifier With Detected Output

Teledyne RF & Microwave

Limiting amplifier sets dynamic range from -10.0 to -5.0 dBm input to 2.0 dBm output. TTL controlled, fast switching and high isolation 10 dB On-to-Off, and includes internal filtering for improved harmonic performance. Analog detector monitored output, or dual RF outputs.

Product Home Contact/Sales Company Catalog Share Add To List
VHF Band 1.0 Watt Amplifier With RF Bypass

Teledyne RF & Microwave

Teledyne RF & Microwave has developed a 35 to 350 MHz custom amplifier with 1 watt output power. The amplifier has 29 dB gain with 3 dB noise figure. The amplifier assembly has a RF switch so that the RF input can be connected directly to the output bypassing the amplifier. The amplifier goes into the "bypass" state when the DC bias is removed from the switch. This unit is one of a series of amplifiers that covers the 1 MHz to 2100 MHz with similar operation.

Product Home Contact/Sales Company Catalog Share Add To List
Voltage Controlled Oscillator Assembly With Heater

Teledyne RF & Microwave

Teledyne RF & Microwave has designed a Voltage Controlled Oscillator to replace an existing application. The oscillator covers the 520 to 560 MHz frequency range. The oscillator provides +10 to +13 dBm output power. The oscillator has internal heaters designed to maintain the oscillator assembly at constant temperature. The unit operates over the 0° to 60° C temperature range with ~200 KHz frequency variation due to temperature variation.

Product Home Contact/Sales Company Catalog Share Add To List
X Band Coupler With Dual Output Threshold Detector

Teledyne RF & Microwave

The X Band coupler with dual output has an input power range of either -5 to +10 dBm, or +5 to +20 dBm. Covering 8.0 to 9.5 GHz, insertion loss is less than 1.0 dB and VSWR is 1.5:1. The coupler/detector has two external resistors providing independently settable threshold TTL outputs. The power flatness is ~0.4 dB and hysteresis is 0.1 dB. Cougar can provide this function in other frequency ranges and input power ranges.

Product Home Contact/Sales Company Catalog Share Add To List
3-5 Watt Power Amplifiers

CCM1095 and CCM2096 - Teledyne RF & Microwave

The CCM1095 and CCM2096 are power amplifiers that use current efficient Silicon Carbide output semi-conductors to achieve +35 to +38 dBm output power. An internal sequencing circuit is included to provide for safe operation of the output power device.

Product Home Contact/Sales Datasheet Company Catalog Share Add To List
Communication Systems

Teledyne RF & Microwave

Tactical networking radio system comprising of transmit/receive modules, converters, synthesizer, RF switching, power supplies, controllers and an antenna array. The radio automatically selects the best communications path to create a self-forming, self-healing network.

Product Home Contact/Sales Company Catalog Share Add To List
Pulsed Transmitter

Teledyne RF & Microwave

Built to operate in harsh environments, the Pulsed Transmitter unit provides radar installation decoy protection in a compact footprint and is powered by a Dewey Generator.The unit is comprised of a power supply, power amplifier, signal generator and antenna, with a fiber optic command and control interface providing throughput speeds capable of 1.25 G bits/sec via 1310 nm, single mode, ruggedized fiber.

Product Home Contact/Sales Company Catalog Share Add To List

Low Noise Dual Band VCO

Topics