TTL
Transistor–transistor logic.
-
Product
PCI 24 Channel TTL Digital Interface
8018S
-
The 8018S Low Profile PCI digital I/O interface provides 24 channels of buffered drive digital I/O emulating 8255 mode zero. The board can be utilized for PC-based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems.
-
Product
PCI 32 Channel TTL Digital Interface
8010
-
The 8010 PCI digital I/O interface provides 32 channels of buffered drive digital I/O, which can be utilized for PC based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems. 10K pull-up resistors are included. Optional values are available.
-
Product
PCI 96 Channel TTL Digital Interface
8009
-
The 8009 digital I/O interface provides 96 channels of buffered drive digital I/O emulating 8255 mode zero, which can be utilized for PC based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems. 10K pull-up resistors are included. Optional values are available.
-
Product
Quad 4 Fold AND/OR/MAJ, NIM-TTL TTL-NIM Translator
V976
-
The Mod. V976 is a 1-unit VME module housing four 4-input Coincidence Fan in/Fan out and NIM – TTL / TTL – NIM adapter sections. Each section features 4 inputs and 4 outputs on LEMO 00 connectors and can operate as a 4 channel level translator or as AND/OR gate.
-
Product
12-bit, 200KHz, 8SE/4DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3110-8
-
The APCI-3110 is a 12-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3110, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
Product
TTL/I2C/SPI* Expansion Kit
OP-SB5GL
-
OP-SB5GL is the interface expansion kit that has a port to measure RS-232C(V.24) and a port to measure the TTL / CMOS signal level communications. The port for TTL / CMOS supports the measurement of TTL / CMOS level communications that power supply system is from 1.8V to 5V. It is suitable for monitoring the communications between the LSI and the interface IC on the printed circuit board by directly probing into the lines. It supports the protocol of not only UART and HDLC but also I2C and SPI* on monitoring and simulating.
-
Product
3.5" Embedded SBC With AMD LX800, Dual LANs, 4 COM, 4 USB 2.0 And VGA/LVDS/TTL
SBC84622
-
The SBC84622 supports an onboard low power AMD LX800 500 MHz processor with the AMD Geode CS5536 chipset. The flexible display function is supported by integrated graphics controller which allows users to configure both CRT and LVDS LCD or CRT and TTL LCD as simultaneous mode. Onboard one DDR SODIMM supports up to 1GB of system memory. Having such compact design with fanless operation, the SBC84622 can be applied in widely embedded and automation applications such as industrial automation, automation control, telecommunication, and process control.
-
Product
TTL/I2C/SPI Expansion Kit
OP-SB85L
-
OP-SB85L is the interface expansion kit that has a port to measure TTL / CMOS signal level communications, and the one to measure the voltage of high-speed analog input. The port for TTL / CMOS supports the measurement of TTL / CMOS level communications that power supply system is from 1.8V to 5V. It is suitable for monitoring the communication between the LSI and the interface IC on the printed circuit board by directly probing into the lines. It supports the protocol of not only UART and HDLC but also I2C and SPI on monitoring and simulating.
-
Product
RS232 / RS485 / RS422 / TTL Serial Repeaters & Hubs
-
CommFront offers a range of rugged, industrial-grade RS232 / RS485 / RS422 / TTL repeaters and hubs to meet serial communications' data distance needs by converting unbalanced signals to balanced ones, deploying repeaters to boost signal strength, and implementing hubs for star-configured connections, while still taking full advantage of cost-effective and readily-available copper wire.
-
Product
USB to TTL Adapter
SKU-012-0X
-
The USB to TTL adapter connects the Serial UART to the standard USB port for testing and monitoring functionality. The Adapter facilitates ease of use and helps to reduce board space and cost.
-
Product
16-bit, 200KHz, 8SE/4DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3116-8
-
The APCI-3116 is a 16-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3116, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
Product
Digital I/O Board, 32 Isolated I/O Channels, 24V +special EEPROM & TTL IO Port
APCI-1500-PULS
-
PCI interface to the 32-bit data bus Connector compatible to PA 1500 Connector and software compatible to CPCI-1500 16 isolated input channels, 24 V, including 14 interruptible 3 software-programmable counters/ timers 16 isolated output channels, 10 to 36 V, output current 500 mA Timer-programmable watchdog for the reset of the outputs"-PULS" version has a special EEPROM and a TTL IO port added at end of cardDiagnostic report through status register in case of short-circuit, overtemperature, voltage drop or watchdog Interrupt triggered through watchdog, timer, error One ground line for all inputs and one ground line for all outputs
-
Product
PXI High Density Digital I/O Module, 32-bit TTL
40-410-001
Digital I/O
The 40-410 range of Digital I/O Modules are suitable for operating external devices, such as heavy duty relays (power, RF and high voltage types), solenoids, lamps, or for interfacing with external logic such as a programmable instrument with a BCD interface.
-
Product
USB To RS232 / RS485 / RS422 / TTL / Serial / Ethernet Converters
-
With our high-quality, high-performance USB to RS232 / RS485 / RS422 / TTL serial and Ethernet converters that use only top-quality chipsets such as FTDI and Silicon Labs, USB signals are converted seamlessly into RS232, RS485, RS422, TTL, serial and Ethernet signals. Pick from our menu of industrial or commercial-grade devices confidently, knowing that you will get nothing but the best from CommFront.
-
Product
RS232 / RS485 / RS422 / TTL Serial Converters
-
Rated to perform at temperatures between -40°F and 185°F (-40°C and 85°C), our rugged industrial-grade RS232 / RS485 / RS422 / TTL serial converters are almost indestructible. These industrial-grade serial converter products support multi-drop RS485 / RS422 networks and come with 600W surge protection, 15KV ESD protection, selectable end-of-line terminators, and optional 2500V opto-isolation circuitry, which ensure crisp data signals without interference for all types of installations.
-
Product
Switched Limiting Amplifier With Detected Output
-
Limiting amplifier sets dynamic range from -10.0 to -5.0 dBm input to 2.0 dBm output. TTL controlled, fast switching and high isolation 10 dB On-to-Off, and includes internal filtering for improved harmonic performance. Analog detector monitored output, or dual RF outputs.
-
Product
X Band Coupler With Dual Output Threshold Detector
-
The X Band coupler with dual output has an input power range of either -5 to +10 dBm, or +5 to +20 dBm. Covering 8.0 to 9.5 GHz, insertion loss is less than 1.0 dB and VSWR is 1.5:1. The coupler/detector has two external resistors providing independently settable threshold TTL outputs. The power flatness is ~0.4 dB and hysteresis is 0.1 dB. Cougar can provide this function in other frequency ranges and input power ranges.
-
Product
Qseven V2.0 SoM With IMX6 Quad/DualLite 800 MHz (Industrial) SoC, 1GB RAM, 4GB EMMC, GbE LAN, Audio And CAN
Q7M120
-
*Qseven v2.0 (70 x 70 mm)*Ultra low power consumption Cortex™-A9*2 CAN*24-bit TTL signal*LVDS/HDMI 1080P*10/100/1000 Mbps Ethernet*Linux 3.0.35/Android 4.3*Audio
-
Product
MAXDIO Connect
-
The MAXDIO Connect panel is a 19 inch rack mount or table top device capable of delivering Push-Pull outputs controlled by Open-Gnd Discrete or TTL Discrete.
-
Product
Multi Protocol Analyzer
LE-2500R
-
LE-3500R/LE-2500R adopted TTL port as its standard besides RS-232C, RS-422, and RS-485 while having the same feature such as small and light body of LE-3500/LE-2500. You can monitor I2C or SPI without expansion board.
-
Product
PCI Module
PCI-ECL-II
-
PCI-ECL-II - with Spartan 6 FPGA, 16Mx32 SDRAM, 20 ECL TX , 20 ECL RX, and 12 TTL IO
-
Product
MPEG-2/1 Frame Grabber and Video Encoder / Decoder
516
-
Real time MPEG-2 and MPEG-1 video encoder and decoder for NTSC, PALText caption buffer for Linux, Windows and QNXOnboard linear 16-bit audio frame grabberLinux, Windows, Windows CE and QNX drivers2 TTL level digital inputs and/or outputs
-
Product
"Signal Transporter"
LTX-5520
-
The LTX-5520 enables the conveyance of sixteen independent channels of digital information over fibre optic links ranging from metres to more than 10 kilometres. Each of the 16 incoming TTL channels is sampled at 50 mega-samples per second, multiplexed and transmitted serially over an optical fibre at a 1 Gb/s data rate.
-
Product
SP4T RF Pin Diode Switches To 16 GHz
-
The 4-way series of absorptive and reflective switches operate from 100 MHz to 16 GHz. They are rated at 200 mW maximum input power and have a switching time of 100 ns. SP4T switches that operate up to 8 GHz have a maximum VSWR of 1.6:1 and minimum isolation of 60 dB. All absorptive and reflective switches manufactured by Pulsar Microwave require both positive and negative 5-volt supplies. Additionally, the TTL control logic operates from 0 to +5 VDC. Voltage connection is made with feed thru terminals. Ground connection is made through the chassis and turret terminals.
-
Product
Bi-Phase Modulators
-
PMI's line of Bi-Phase Modulators includes a comprehensive selection of different models which cover broad octave frequency bands ranging from 0.5 to 40 GHz. Bi-phase modulators take a TTL level digital bits stream that’s encoded onto the RF carrier using 2 Phase Shift Keying (2PSK) modulation, where the 2 phases are separated by 180º. This performance is desirable in communications systems, microwave radio, radar, high data rate test & measurement, serial data transmission, base station infrastructure, and other industrial and military applications.
-
Product
SMARC V1.0 SoM With IMX6 Quad/DualLite 800 MHz (Industrial) SoC, 1GB RAM, 4GB EMMC, GbE LAN, Audio, CAN, MIPI And PCAM
SCM120
-
*SMARC 1.0 (82 x 50 mm)*Ultra low power consumption Cortex™-A9*2 CAN 2.0B*24-bit TTL signal*LVDS/HDMI 1080P*10/100/1000 Mbps Ethernet*Linux3.0.35/Android 4.3*Audio
-
Product
RS232 RS485 RS422 Serial To Ethernet Modbus Converters / Device Servers
-
In the past two decades, legacy serial communication protocols such as Modbus have merged rapidly with modern TCP/IP communication, yielding benefits including widely available infrastructures and greater distance, reliability, and flexibility. CommFront offers a range of industry-proven, easy-to-use serial to Ethernet converters and device servers, both hardware and software types. The applications of our serial to Ethernet converters include acting as a device server or a Modbus RTU/ASCII to Modbus TCP protocol converter; extending serial ( RS232 / RS485 / RS422 / TTL) communication distance over Ethernet network; controlling serial devices from remote Modbus TCP software or Modbus RTU master via Ethernet network; making a wide variety of M2M communication applications possible by enabling client access independent of any operating system or proprietary protocol; and converting conventional serial data network into TCP/IP network, etc.
-
Product
SP5T RF Pin Diode Switches To 12 GHz
-
Pulsar Microwave's 5-way RF switches cover bands from 300 MHz to 12 GHz in both absorptive and reflective configuration. These SP5T switches have a rating of 200 mW maximum input power and a switching time of 100 ns. They are specified with a minimum isolation of 60 dB and most models maintain a VSWR of 1.6:1 or better on all ports. The SP5T switches are driven by TTL logic control circuitry and require both positive and negative 5-volt supplies for operation. A 9-pin D-SUB connector provides the interface for the power and logic voltages.
-
Product
CPCI or PXI Digital IO Board
MS 1802
-
*Bus Interface - PCI Bus*Number of Channels 198*Compatibility - TTL*Power on state - Inputs (high-Z), pulled up or down (jumper selectable)*Handshaking - Input, Output, or bi-directional*Data transfers - Interrupts, programmed I/O*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
High Power Fiber Laser
-
Amonics' Fiber Laser (AFL) is a compact standalone turnkey equipment to deliver up to 50W output power and 1mJ pulse energy in 1064nm and 1550nm range under CW or pulse operation. Based on proprietary all fiber design, Amonics fiber laser is maintenance free. No post-installation service is required.In pulse operation, the laser delivers up to 20kW peak power and adjustable pulse width from 10ns to 1000ns. The pulse repetition rate is triggered by external TTL signal.Amonics fiber lasers are the ideal candidate for a wide range of industrial applications.
