Ground Continuity Test

The 230A tests thin Ethernet (BNC), 10BaseT (UTP/STP), 100BaseTx, RJ45, TIA 568A, TIA 568B, and Token Ring cables within a few seconds. It detects miswiring, polarization, and continuity. The 230A also tests the ground of shielded twisted pair cables. With the remote unit, you can remotely test installed cable either from the wall plate or pat ...more

The HTT-1 was designed to provide a fast, safe and reliable way to verify proper operation of Dielectric Withstand (hipot) and Ground Continuity Testers between calibration cycles. It allows the operator to check the result of the three failure modes encountered in production hipot and ground circuit testing (open ground, high leakage current, ...more

The GF-30AC is a production line workhorse. This unit delivers a constant AC current while checking impedence. This unit protects product under test as internal current limiting prevents over-current excursions. Test results indicated by red and green LED's, audible buzzer on failure V=IRtual voltage sense circuit compensates for any resistanc ...more

Accurate ground resistance measurement from 0.025 to 1500 Ohms. TRMS current measurement including leakage current. Continuity beep if the resistance is lower than 40.00 Ohms  ...more

Quickly check for circuit voltage, or continuity! Indicates four voltage ranges from 6V to 24V. Quick check to test injector firing, primary ignition circuits, bad grounds, broken wires, fusible links and more! ...more

Larger Clamp Size (1.25"). Backlight. Ground resistance (0.1 to 1200?). Ground leakage current to 30A. Ground continuity loop test. Audible alarm. Data Storage  ...more

The B433R is a cost effective simple to use, rugged, earth / ground bond test systemsuited to manufacturing or laboratory environments. This earth / ground bond tester can deliver a test current of 25A through a resistance/impedance of 0.1½ from a low voltage a.c. source. This earth/ ground bond tester meets the general requirements of the major ...more

The WT25 WRISTAT Tester is designed to test the integrity of our WRISTAT in a fast, efficient and simple manner. All of the elements of the WRISTAT - continuity of the strap, integrity of the protective resistor, and satisfactory strap to skin contact are easily confirmed by pressing the top cover of the WT25. The operator (wearer) is tested f ...more

Designed to test any type of non-live electrical circuit. Track down broken wires, bad grounds and blown fuses quickly. Features and Benefits. Comes with AAA Alkaline battery. Ergonomic, slim designed clear handle. 12-foot red coil cord. Low voltage replaceable bulb. Molded strain relief. Heavy-duty stainless steel probe with insulated shaft. ...more

ISOTEST2010 model performs Insulation Resistance measurements on each electrical installation with test voltage selectable from 50 and 1000VDC and permits also Continuity test of potential equalising circuits and protective conductors according to VDE 0413. Flexibility of this meter consents also to perform measurements on power circuits of swi ...more

Meets UL, CSA, CE, IEC and all other international safety agency requirements. 1 Button Testing - No setup required, just plug right in! Easy to identify PASS / FAIL (anyone can operate!) Also performs the Low Current Ground Continuity test, at the same time! Custom ?Universal? receptacle accepts both 120V and 240V plugs.  ...more

If you need a continuity function or harmonics are a problem then the Voltman TRMS is for you. Non sinusoidal waveforms from variable speed motors cause problems for most meters but the Voltman TRMS meter is specifically designed to produce accurate and dependable readings of distorted waveforms. When there is no voltage present the unit autom ...more

Introducing the world?s fastest, easiest, and most affordable Automated digital Ground Continuity tester. Simply put, the new Millennium Series GC1000 tester from ED&D makes all others obsolete. This is the only such tester available produced by experts in Product Safety!  ...more

Performs GPIB interfacing between computer/controllers and ROD-L Hipot, Ground Continuity and Insulation Resistance Testers ...more

Performs GPIB interfacing between computer/controllers and ROD-L Hipot, Ground Continuity and Insulation Resistance Testers ...more

Production / Quality Assurance Testing - Performs ground continuity tests in full compliance with BSI, VDE and IEC. Measures ground continuity from ground to the power cord ground pin of the DUT. Interface enables interconnection to any ROD-L Hipot & Leakage testers to form a complete automatic test system. ...more

Each test load provides two test operations for verifying functionality of a Hipot Tester and Ground Continuity Tester. Provides two ground continuity tests (open and short) at up to 35 amperes maximum ...more

The MC30 Series provides remote control and data acquisitions for ROD-L Hipot and Ground Continuity test instruments. ...more

Performs ground continuity tests in full compliance with BSI, VDE and IEC. Measures AC resistance from Chassis of Device Under Test (DUT) to power-cord ground lead - 0 to 0.15 ohm ...more

Performs ground continuity tests in full compliance with BSI, VDE and IEC. Measures AC resistance from Chassis of Device Under Test (DUT) to power-cord ground lead - 0 to 0.15 ohm ...more

Multi-Network cable tester is specified to quickly test by auto scanning the wires continuity, miss-wiring and polarization in your network cables, thin Ethernet (BNC) /10Base-T (UTP / STP) / 356A / TIA-568A / TIA-568B / Token Ring. By using the attached remote terminator, you can easily test the cable whatever before or after the cables installed. ...more

Multi-Network cable tester is specified to quickly test by auto scanning the wires continuity, miss-wiring and polarization in your network cables, thin Ethernet (BNC) /10Base-T (UTP / STP) / 356A / TIA-568A / TIA-568B / Token Ring. By using the attached remote terminator, you can easily test the cable whatever before or after the cables installed. ...more

Each test load provides two test operations for verifying functionality of a Hipot Tester and Ground Continuity Tester. Provides two ground continuity tests (open and short) at up to 35 amperes maximum ...more

The insulation resistance tester IRT-S is engineerd for accurate measuring of LV-installations and appliances according the EN 61557 regulation. The tester has been developped to measure voltage, frequency and continuity. Also insulation resistance of high sensitive parts and even heavy machines or ground cables can easily be measured with the ...more

Performs concurrent ground continuity test. ARC and OVERCURRENT detection circuits. Fast discharge of Device Under Test (DUT) and other test standards ...more