Capacitor Testers

DPW testers are used for DC proof testing of high voltage equipment in power engineering. Routine testing of the insulation and leakage is a necessary requirement for surge arresters. Other areas include: Cable breakdown testing, capacitor charging and general laboratory use. ...more

These portable testers have been designed to be used in testing high voltage equipment in power engineering. Routine testing of the insulation and leakage is a necessary requirement for surge arresters, cable breakdown testing, capacitor charging and other laboratory use. ...more

Insulating Oil Testers are designed for the easy and accurate determination of the di-electric strength of insulating oils used in transformers, switchgears, bushings, capacitors and other electrical apparatus. They are ideal for on-site and laboratory use. Safe and easy operation has made UDEY insulating oil testers the industry standard for m ...more

Benchtop cable tester packs impressive capabilities into a small, easy-to-use package that fits almost any budget. The large display, coupled with a sensible and easy-to-understand button interface, makes the setup and testing of cables quick and intuitive. Test Point Range: 128-1024, Test Voltage: 5VDC 6mA max current. ...more

The flexible high capacity test system (SCT) is designed for testing and grading of either single ultracapacitors or blocks of capacitors (parallel - serial). The system meets customers' specification in regards of voltage range, current range and number of circuits. The Ultracapacitor Test System, UCT, is designed for R&D and production lot testin ...more

FH - The FH tester executes a single pass hysteresis loop in 1µs with no interlacing of the data acquisition. Pulse widths ranging from less than 100ns up to 100ms on capacitors with areas ranging from 5µx5µ up to 100µx100µ. ...more

Identifies good, bad and leaking capacitors. Built in test leads.  ...more

Wilcom T124 Cable Shield Splice Tester is an accurate measuring device which provides measurement of the conditions existing at cable shield splices, checks the integrity of ground connection, and checks the condition of capacitors across insulated splices. Two probes, capacitively coupled to the shield of the cable under test, are connected t ...more

VON Impulse Service Capacitors have evolved through several stages of development to their present superior design for use in capacitance discharge fault locating with a VON tester and impulse control gap. Both terminals are on top of the insulated plastic case for ease of connecting capacitors in series or parallel.  ...more

Identifies good, bad and leaking capacitors. Checks continuity of fuses and transformers. Testing current 1mA max. Built in test leads ...more

Memory window information based on analog hysteresis measurements on single cell capacitors after full integration process. Quality control during production based on memory window information which is not influenced by deviation of CMOS process. Single shot hysteresis data at MHz operation speed. Classification of bit failure instead of bit failur ...more

Designed for commercial, military, and aerospace applications, the CH+ provides the capability of testers costing many times its price. Easy-to-use, powerful Windows-based software makes the CH+ the choice of many high-end users. Test Points: 256-5376, Hipot: 50-1500VDC, 100-1000VAC ...more

Advanced Hipot Tester with Graphical Touch-Screen Control. 4.1 Mb, Audio and Video, 100 second run time, requires Flash plug-in. oint Labeling: Standard Adapter Labeling or Custom 30 Characters. Components: Resistors, Diodes, Capacitors, Twisted Pairs, Custom ...more

ESI's Model 3550 performs electrical testing of High Cap multi-layer ceramic capacitors (MLCC) at productivity rates of up to 9,000 chips per minute. Multiple tests are simultaneously performed on chips as small as 01005 (0402 metric) on an advanced handler using ESI's non-jamming patented rotary technology. ...more

The DB232 Component Tester is especially designed for high accuracy testing of capacitors on production lines, not least for integration with sorting machines in a production environment. Measuring frequencies: 100kHz, 10kHz, 1kHz and 100Hz ...more

The Model 50102-G-01 is used to detect the presence of voltage or capacitance on overhead or underground cabling or on switch gear and MCC Panels. It is an excellent mistake-proof safety tester to check lines, bus bars, or capacitors before crews start to work. ...more

The Quick-Check® Transformer and Capacitor Tester is a versatile tool for quick and easy checks of capacitors, transformers and the connections made to them. In the field, the Quick-Check is used to test the primary and secondary sides of single- or three-phase transformer installations for short circuits prior to energizing. ...more

The DB233 Component Tester is specially designed for manual as well as automatic high-speed high accuracy testing of capacitors or other CLR applications. 4 measuring frequencies: 100kHz, 10kHz, 1kHz and 100Hz ...more

The DB231 Component Tester is specially designed for manual as well as automatic high accuracy and high-speed testing of capacitors or other CLR applications. 1MHz, 100kHz, 10kHz and 1kHz ...more

The Dynalab NX Pro Wire Harness Tester is a low-cost, feature-packed, stand-alone continuity tester with a maximum capability of 512 test points. The flexibility of the NX System allows each program to perform multiple tests, display custom messages or sounds, and analyze the results of a test or an input to "decide" which operation ...more

The DB230 Component Tester is especially designed for high accuracy testing of capacitors on production lines, not least for integration with sorting machines in a production environment. The instrument is reliable, user-friendly and easy to set up to any test. ...more

The Impulse coil winding tester tests electrical characteristics of coil windings without damage to the samples. The master coil and a test coil are supplied with the same electric Impulse by capacitor discharge, and voltage decay waveforms generated by these coils as below. Also, poor insulation will appear as corona or layer discharge. ...more

The Dynalab NX Pro+ Wire HarnessTester is modular and is designed for applications requiring up to 32,768 test points. It has the same "front end" as the NX Pro Tester, but employs a series of Expansion Units to accommodate the test point cards. Testing for continuity, shorts, diodes, resistors, capacitors. Highly flexible and adapta ...more

The Cap Check line of capacitor testers is designed to identify internal problems with a capacitor or capacitor bank. The instruments are proven to be a valuable asset in maintaining both pole-mounted and substation capacitors. The testers will identify bad or failing capacitors that may rupture upon energizing. ...more

The DB236 High Capacitance Tester is specially designed for high accuracy and automatic high speed testing of large capacitance’s such as metallized film, tantalum and aluminium capacitors. Measuring frequencies: 100kHz, 10kHz, 1kHz and 100Hz (120Hz) ...more