-
product
PXI 3A Power MUX BRIC, 20-Channel, 12-Pole
40-571-305
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
Milli-Ohmmeter and Bond Meter, Portable, 10 µΩ to 20Ω
R1L-BR
The R1L-B series Ohmmeter/Bonding Tester is a digital microohmmeter designed to measure resistances from 10 to 20 . It is used in applications such as metal bonding, switch, circuit breaker, circuit resistance and other contact and connection resistance tests as well as higher resistance measurements for circuit analysis and resistor testing up to 20 . The instruments utilize the four-terminal, Kelvin technique to eliminate errors caused by the resistance of the leads. Resistance readings are viewed on a 3 1/2 digit display,
-
product
PXI 8 Trib Daisy Chain Switch 120Ohm Balance
40-795-001
The 40-795/796 Daisy Chain Switching Module is designed for telecom test applications. It allows production or verification testing of SONET/SDH transmission multiplexers switching 2MBit/s or 1.5MBit/s data over 100 or 120 balanced lines.
-
product
Functional, regression, load and integration Testing
Rational Test Workbench
BM Rational Test Workbench delivers end-to-end functional, regression, load, and integration testing to address the quality challenges of highly complex applications.
-
product
High Frequency (RF) Testing
C.C.P. Contact Probes Co., LTD.
CCP designs high frequency testing probes, coaxial probe sockets and pressurized conductive rubber sockets.
-
product
Vibration Test
Vibration testing determines the dynamic effects on component part of vibration within the frequency ranges and magnitudes that may be encountered during field service. Vibration, for example, causes loosening of parts or relative motion between parts in the specimen, producing objectionable operating characteristics, noise, wear, and physical distortion, and often results in fatigue and failure of mechanical parts.
-
product
5A Microohm Meter
9005 UO
Standard Electric Works Co., Ltd
● Maximum testing current of 5A ● Ranges: 2000μΩ / 20.00mΩ 5A 20.00mΩ / 200.0mΩ 1A 2.000Ω / 20.00Ω 100mA 200.0Ω 10mA● Maximum resolution of 1μΩ at 5A● Four terminal measurement● 4 Lines × 20 Characters LCD ● Memery function (200 measurement results)● Auto power off● Low battery indication● Power source: 1.5V "C" alkaline battery × 8● Safety Standard: EN 61010-1 CAT III 300V EN 61326-1
-
product
Mobile Cable Fault Location System
Syscompact 2000
BAUR Prüf- und Messtechnik GmbH
Fault location with Syscompact 2000. The Syscompact 2000 is a multifunctional cable fault location system designed for modular 19" rack technology. The integrated surge and test generator is used for cable and sheath testing as well as for precise location of high-resistive and intermittent faults. The SYSCOMPACT 2000 is preferably used in low- and medium-voltage networks for fault location up to a cable lengths of 65 km. * Fast and reliable * Precise, dependable cable fault location High performance * high voltage unit* Integrated proven cable fault pre-location methods
-
product
IoT Devices Penetration Testing
There is a rising concern that IoT devices are being developed rapidly without appropriate consideration of the profound security challenges involved, as demonstrated by the various IoT devices hacked in recent years— automobiles, cameras, children's toys, thermostats, and medical devices.With more than a decade of specialized cyber security testing experience combined with our extensive research and development, we can assess and identify both common and complex security vulnerabilities that may be residing within your whole IoT ecosystem.
-
product
Three Phase Numerical Relay Testing Kit.
Nmc make fully automatic three phase Numerical relay testing kit , Model : DYJB-PC3.
-
product
Coupling Decoupling Network
TBCDN-M3
The TBCDN-M3 is a Coupling Decoupling Network for conducted immunity testing according to IEC 61000-4-6.
-
product
Network Testing Portfolio
TEMS™
The TEMS™ Network Testing Portfolio allows you to optimize the quality of your mobile network by concentrating on user experience. TEMS gives you the ability to walk test, drive test, and dynamically analyze your mobile network under the real-life conditions your users experience—indoors, outdoors, and around the clock.
-
product
Safety Chamber, Hydrostatic Test
9901HTX-72x24x12
The 6 ft wide by 2 ft deep Hydrostatic Test Safety Chamber, when combined with one of our pump systems, provides a complete hydrostatic test system for testing hose and assemblies or other components requiring pressure testing.
-
product
Optical Fiber Analysis System
2200
The 2200 Optical Fiber Analysis System provide high-speed characterization of the spectral loss of single-mode and multimode fibers. Configurations include the 2200 for single-mode fibers, the 2210 for both single-mode and multimode fibers, and the 2220 designed for single-mode fiber ribbons. All three systems employ unique fiber preparation and signal processing techniques, which deliver both the measurement performance and the testing throughput required by high volume fiber, cable and component manufacturers. Options are available for mode field diameter and multimode numerical aperture measurements.
-
product
Becker NAV/RMU/RMI/OBS Test Fixture
TA-3320
This NAV test fixture is specific to the requirements for testing Becker Avionics NAV, RMI and RMU products. The panel incorporates specific functionality required for testing these Becker products by the book including special requirements for the RMU 5000 and the IN 3300 series of nav indicators. This BAEE NAV test fixture also facilitates resolver alignment and discrete meter testing through the PG 3300 interface connector. The RM 3300 portion of the panel tests the Becker RMI indicators and ...show more -
product
AINC 429 Multichannel Interface with Additional ARINC-717 Receive & Transmit Channels
DAS-429UNET/RT8-717
The DAS-429UNET/RT8-717 is an ARINC 429, multichannel interface card with additional ARINC-717 receive and transmit channels. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the ARINC 429 & ARINC-717 bus, both in the lab and in the field.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each...show more -
product
Multi Function Automobile Tester
6521
Peaceful Thriving Enterprise Co Ltd
The multi-function automobile tester has LCD display to indicate the measured result. It has polarity detection with the LEDs for a positive and negative indication of DC voltage. For auto use, the functions included the measurement of DC voltage and current, signal frequency and max/min voltage, resistance and power providing testing.
-
product
Product Testing
Cotton Electric Services, Inc.
Cotton Services is accredited through the National Association of Independent Laboratories (NAIL). Our Testing equiptment goes through a calibration process at least once a year and on-site tests are routinely performed by factory officials to ensure testing accuracy. Cotton Services Employees are certified in equipment maintenance and testing procedures. All products are tested at or above minimum test ranges set by the industry.
-
product
Large Flow 1 CFM Particulate Counter
CHY-001
This air particle counter can measure the particle in the air, with 2.83L/min air flow and 28.3L/min large air flow testing.
-
product
Automated Testing
IRWindows™5
IRWindows™5 from Santa Barbara Infrared is an advanced software tool that automates the setup, execution, data collection and results analysis for industry standard performance testing of infrared, visible and laser systems. IRWindows™5 is the most advanced commercially available IR/EO sensor test software package in the industry today. It operates under Windows™ OS and is delivered installed on a high-end PC computer platform with frame grabber(s) selected to support UUT video formats. It is al...show more -
product
PNA Network Analyzers
The PNA Series of network analyzers offers industry-leading performance for testing amplifiers, mixers, and frequency converters. Built-in pulse modulators and pulse generators provide pulsed S-parameter measurements quickly and accurately. All models are available in two-port single-source and four-port dual-source versions.
-
product
Decade Box, Calibrated W/Data, Capacitance, 5, 100pF to 11111µF, 5 %
72-7265 CAL D
The 72-7265 CAL D from Tenma is a capacitance decade box. It is ideal for service, prototype and experimental use. This useful tool may be set at any non polarized capacitor value from 100pF to 11,111µF in 100pF increments. The decade accuracy is ±5% capacitors used throughout at <1μF, 1KHz test frequency, ≥1μF, 100Hz test frequency. It has weight of 304g/0.69lb and dimension is 14.7cm × 11.7cm × 5.5cm (5.79" × 4.61" × 2.16"). It is typically used in general applications, troubleshooting, maintenance, education and vocational training, production line testing, radio and TV services, working standards, research design & develop, physics laboratory work.
-
product
PAT Testing
At Seaward, we have been leading the way for over 41 years with our PAT testing equipment, software and accessories. Continuous innovation and investment in our product range means we offer marketing-defining solutions for our customers.
-
product
Meter Test Bench
Meter Test Banch is available with high-technology to ensure high testing accuracy as well as maximum functionality. It is designed to provide precise results in any simple to complex testing. It comes with modern systems to ensure to provide artificial load that cannot be changed in the power supply. It is provided with high durability and efficacy to ensure long lasting life with no maintenance. In addition to this, it ensures high accuracy in testing without any wear.
-
product
Partial Discharge Inductor
Tracy
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR tracy. The BAUR tracy partial discharge inductor induces a signal at the apparent fault location in the cable from outside. In combination with any PD measurement system, e.g., PHG TD/PD, the induced signal can be located and compared with the result of the partial discharge pre-location. The partial discharge location can thus be determined precisely.* Portable, battery-operated signal coupling device* Suitable for cables and cable accessories* Inductive signal coupling* Aviods costly, unnecessary replacements of PD-free cable accessories
-
product
Coating Thickness Meters
PCE Instruments' accurate, affordable coating thickness gauge, thickness meter, surface testing and film gauge devices are used for material testing, manufacturing quality control and automotive paint inspection applications. Choose from a variety of coating thickness gauge, mil gage or paint meter products used for the non-destructive measurement of nonmagnetic coating, insulating layer and dry film thickness (DFT) on ferrous and / or non-ferrous metal substrates such as steel and aluminum.
-
product
Wafer Test
Silicon Turnkey Solution, Inc.
Most foundries provide wafers already probed to a set of DC parameters at room temperature to ensure they meet a basic subset of the package-part specification. Beyond this basic set of tests, more rigorous testing is often needed to meet specifications requiring die to be 100 percent probed, identify and segregate devices with higher performance levels and guarantee that parts will perform to a certain specification level.
-
product
Ozone Climatic Test Chamber
The Ozone Test Chamber provide an effective solution to the testing of products for resistance against ozone degradation in a controlled environment. These test chambers function as static tensile test chambers as well as Rubber Test Chamber and are often used for studying static tensile deformation of various manufactured goods in the presence of ozone. The equipment works by exposing the test samples to uniform concentrations of ozone at constant temperatures and relative humidity in a sealed air environment. Under these conditions, the products undergo the process of corrosion which can be observed in the form of surface cracks and changes in other properties.
-
product
PowerNet Tester
The PowerNet Tester (BNT) is designed to test batteries, ultracaps and all other types of electrochemical power sources for 14 V and 42 V power net systems. Designed to test vehicle system batteries for 14V and 42V power net systems. But they may also be used for testing all other types of electrochemical power sources just by setting the required current and voltage values.
-
product
PXI 16x SPST High Voltage Reed Relays
40-310-101
The 40-310/320 Range of High Voltage Switching Modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications for the 40-310/320 series modules include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.