Light: Visible spectrum of electromagnetic radiation from 400nm to 700nm.

Showing results 421 - 435 of 1984 products found

  • Electrical Testers

    Curt Manufacturing

    Part of towing responsibly is making sure your trailer lights are working properly. Whether you have just installed a new vehicle-to-trailer wiring harness or are trying to locate the cause of an electrical problem, CURT connector testers are great for testing tail lights, turn signals, brake lights, ground connections and other electrical components on your trailer.

  • Digital Illumination Meter

    Shenzhen UYIGAO Electronic Technology Co., Ltd

    Is a device used to measure the amount of light. In photography, a light meter is often used to determine the proper exposure for a photograph. Typically a light meter will include either digital or analog electronic circuit, which allows the photographer to determine which shutter speed and f-number should be selected for an optimum exposure, given a certain lighting situation and film speed.

  • DB-9 PockeTester™

    Model 51 - Patton Electronics Co.

    The Patton Model 51 DB-9 PockeTester™ monitors the seven most important async EIA-574 (RS-232 on a DB-9) data and control lines. The Model 51 uses seven tri-state LEDs to indicate the presence of the following signals: TD, RD, DTR, DSR, RTS, CTS and DCD. A red light = Mark, a green light = Space and no light indicates no signal on the line. No AC power or batteries required..

  • Flash Parallel Solar Simulator

    All Real Technology Co. Ltd.

    All-Real Flash Parallel Solar Simulator - HCPV module tests comprises three major parts of flash light source, HCPV module power rating station and IV Tracer. Light Source and collimated mirror: The collimated angle of radiation is within ± 0.5° very similar to the real sun (with a controlled reference spectrum similar to AM 1.5D) to well simulate natural sun light and leads to accurate measurement. IV Tracer:

  • Fork Sensors

    SICK Sensor Intelligence

    Fork sensors, which operate using a through-beam design, combine the sender and receiver in a single housing. As a result, alignment is no longer time-consuming. Even very slight differences in light attenuation are detected due to highly focused light emission and high detection accuracy. Easy installation, high immunity to ambient light, and a wide range of fork widths are some of the many advantages that SICK fork sensors offer. Applications include detecting labels or parts on conveyors.

  • Fiber Break Tester

    27555 - C2G, Lastar, Inc.

    Sends a visible red laser light down the fiber locating any breaks or unseen faults. The Fiber Break Tester from Cables To Go is a pocket sized tool that sends a visible red laser light though fiber optic cables. Breaks or faults in the fiber will refract the light, creating a bright glow around the faulty area.

  • Fiber Installation Tools

    FiTs - Liverage Corp

    The FiTs is a handy instrument to provide several wavelengths for testing the fiber equipment in an optical network and FTTx construction. There are 650 nm Fiber Checker & Light Source is deal for field or laboratory testing of optical communication systems at visible light 650 nm and 850 nm / 1310 nm / 1490 nm / 1550 nm . Light Source features zero warm up, superb productivity and is easy to use with its pocket-size and rugged handy design.

  • Handheld Spectrometer

    UPRtek PG100N - Gamma Scientific Inc.

    The PG100N is a lightweight, portable, and easy-to-operate Spectral Light Meter or Spectral Illuminance (LUX) Meter designed for agriculture and horticulture applications. It is an interactive system and offers analytical reporting for spectrum, PPFD, PFD, auto-monitoring, and other parameters needed to understand ambient light conditions for plant growth and the adjustment of artificial light sources to efficiently control production, safety, and yield.

  • Plastic optical fiber Indicator

    OFT-420D POF - OPTOKON a.s.

    The OFT-420D POF Indicator is designed for POF – Plastic optical fiber network testing. It combines two optical test equipments – Light Source and Power Indicator in the same box. The optical Light Source sends optical light either into one or both fibers of duplex output inteface, available in working wavelength 650 nm. The optical Power Indicator is designed...

  • Photocell Relays

    Entes Elektronik

    FG type photoelectric (twilight) switches monitor the daylight in connection with a light sensor (light dependent resistor, LDR) specially developed for this purpose. These switches are used on yards, streets or shop windows for automatically switching the lights ON at the beginning of darkness and switching them OFF in the morning. The sensor is installed in a water tight, surface mount container that is made of heat resistant acrylic material.

  • Radiometers

    ACCU - CAL ™ 160 - Dymax Corporation

    Simplify Validation and Monitoring of Your UV or LED Light-Curing Process. Consistent light curing requires periodic monitoring of light intensity or dose. The ACCU-CAL 160 radiometer is available in both a UV and LED model and can measure UV or LED light up to 10 W/cm2 emitted from stationary light-curing flood lamps or lamps used in conveyorized processes. This radiometer can be used to determine intensity (measured in mW/cm2).

  • Rigid Borescopes

    RGB-1000/RGB-1700 - Phase II Plus

    Portable, rugged design enables user to view critical components in high resolution through access holes as small as .160” (4mm). RGB-1000 Utilizes a high intensity tungsten halogen light source operated by 2 AA batteries. RGB-1700 Utilizes a Super bright LED Light source operated by 3 AA Batteries Built-in light source affords user extreme versatility anywhere in the shop.

  • Highly Collimated Solar Simulators

    Sciencetech, Inc.

    This solar simulator is based on a Fresnel lens to collimate the light beam from the arc lamp source to infinity, which results in highly collimated illumination of the target spot. A 2.5kW xenon ozone free lamp is used as the light source. The spectral distribution of the xenon light source, along with the use of specially calibrated AirMass filters, closely simulates the sun’s true spectral distribution in various conditions on Earth.

  • Fiber Continuity Tester

    ST90 - Elenco Electronics Inc.

    Clips conveniently into a shirt pocket. Krypton light is extremely bright, yet much safer than laser sources. Tester acts as inspection back light. Operates on 2 AA batteries (not included).Powerful Krypton light source provides long range over multimode fiber.Soft ferule gripping membrane is designed to protect finished ferrules while firmly securing the connector in the tester body.

  • Concentrator Solar Cell Module On Sun Test System

    RIVSeries - SW Link Ltd

    RIV series Concentrator Solar Cell/Module test system is designed by SW Link Ltd for measuring light IV curve of a single CPV Module, under CW concentrated light sources, as well as with short pulse light illuminations.

Products

Applications

Manufacturers