Wave form
-
Product
Telecom Test Systems
4301 Series
-
The 4301 is designed to work with a standard arbitrary wave form generator or signal source that can be triggered. The system can be ordered with an optional Fluke 281 arbitrary waveform generator, which comes pre-programmed and integrated into the 4301 system. When equipped with the Fluke 281 option, the 4301 provides a complete solution for GR-1089 Section 10/ATIS-0600315.2007 testing.
-
Product
PXIe Avionics Interface Cards
Interface
The OmniBus II PXIe is the next-generation of Astronics' popular OmniBus product with faster I/O and processing capabilities. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box. Readily available as Commercial Off-The-Shelf (COTS) products, the PCIe interface is perfect for challenging simulation, test, interface, and data recording applications.
-
Product
Magneto-Electric Rotation Detector
MP-981/AP-981
-
The MP-981 is a magneto-type detector using a hall element which is suitable for revolution (r/min) measurement from low speed to high speed.Magneto-type detectors use an internal hall element, a permanent magnet, DC amplifier, and voltage regulator and respond to flux, so that a rectangular wave form is derivable from much lower speed all the way though high speed.In addition, a signal indicator is provided in spite of the detector's compact design, making verification of operation and mounting position possible.Meanwhile, the AP-981 is the water and acid proof type, which conforms to Class ' of JIS C0920.
-
Product
Oscillators for Radio Amateurs
-
An oscillator is an electronic circuit designed to produce either audio or radio frequency signals. These will generally have sineusoidal wave form, but other wave shapes such as square and sawtooth are possible. In radio equipment oscillators will always have a low output power, and if a radio frequency is produced, the oscillator is acually a basic radio transmitter.
-
Product
1000 Amp AC/DC True RMS Digital Clamp Meter
DL6404
-
The top of the range DL6404 provides True RMS reading on AC current and AC voltages allowing accurate measurement regardless of the wave form. This makes it the ideal instrument for commercial and industrial applications where non linear loads are present.
-
Product
4-CH 10/12-Bit 20 MS/s Simultaneous-Sampling Analog Input Cards
PCI-9812
Analog Input Module
ADLINK’s PCI-9812 and PCI-9810 are 4-CH, 10 or 12-bit, 20 MS/s simultaneous-sampling analog input cards. The high-speed analog input channels are single-ended, with hardware programmable input ranges of ±1 V, ±5 V and input impedances of 50 Ω, 1.25 k Ω and 15 M Ω. The onboard 32 k-sample A/D FIFO can buffer so data throughput is less than 100 Mbytes/s, the FIFO performs as the temporary A/D sample buffer, and as a rule of thumb, no data loss will occur. When four channels operate at 20 MS/s simultaneously, each sample generates two bytes, resulting in 160 Mbyes/s (4 channels * 20 M * 2 bytes) throughput, which exceeds the peak 132 Mbyte/s bandwidth of PCI bus. To avoid data loss, the 32 k-sample FIFO is the limitation of sample count. In addition to the onboard 40 MHz time base, users are able to supply the external time base in either sine wave or digital forms. The PCI-9810 and PCI-9812 also feature external digital trigger and programmable analog trigger, thus the conversion start point of multiple cards can be synchronized to external events. The trigger modes include software-trigger, pre-trigger, post-trigger, middle-trigger and delay trigger, further expands the capabilities of these high-speed devices. ADLINK"s PCI-9812 and PCI-9810 deliver cost-effective and reliable data acquisition capabilities and are ideal for vibration testing, image digitizing, ultrasonic measurement, biomedical research, ATE and other high-end industrial, scientific, and military applications.
-
Product
ESD & Latch-Up Test System
-
Identify and help correct ESD and latch-up susceptibility issues on sensitive integrated circuit components prior to full-scale production with the Thermo Scientific™ MK.2-SE ESD and Latch-Up Test System. The MK.2-SE test system provides advanced capabilities to test high pin count IC devices to Human Body Model (HBM) and Machine Model (MM) ESD standards. The system’s pulse delivery design addresses wave form hazards such as trailing pulse and pre-discharge voltage rise, and performs Latch-Up testing per the JEDEC EIA/JESD 78 Method.
-
Product
Pulse Tesla Meter
GP-300
-
Pulse field intensity can be read directly. Wave form is observed by oscilloscope. Measuring range:0.01T~9.99T .
-
Product
Digital Surge Tester
KT-905D
-
Surge Tester of KAST is divided for the use of 3¡40 §Ç by output voltage, and subdivided into type C of manual decision type, type A of auto decision type, type L of exclusive use for low inductance product test and type P loading printer which can printout its wave form and digital scope. Surge test requires only 0.5 second. Because Surge tester already performs 30 times of Impulse voltage test only for 0.5 second. Turn-to-turn short : phenomenon shorted between the side coils.
-
Product
1000 Amp AC True RMS Digital Clamp Meter
DL6403
-
True RMS reading on AC current and AC voltages provide accurate measurement regardless of the wave form, which makes this the ideal instrument for commercial and industrial applications where no linear loads are present.
-
Product
Databus-to-Network Interfaces
OBB2
Interface
The OBB2 is highly configurable and includes built-in standard peripherals (Ethernet, serial, and USB), along with four internal Cores that can be populated with a variety of databus protocols and discrete I/O modules. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box.
-
Product
Impulse Tester
MIG2412SPD
-
The MIG2412SPD is a impulse tester for testing SPD (Surge Protection Devices) in accordance with IEC 61643-1 and VDE 0675. Up to maximum 24kV/12kA making it suitable for testing Class I to III or in accordance with VDE Class A,C, D. The MIG2412SPD is a hybrid generator with a voltage wave shape 1,2/50 ìs at "no load" and a current wave form 8/20 ìs at short circuit for testing Class III (D) SPD connected to power line.
-
Product
Rotating Ring Disk Electrode
RRDE-3A
-
RRDE-3A is a constant rotation system for use in hydrodynamic modulation rotating ring disk electrochemistry. A 7 mm diameter electrode with short stainless steel shaft provides for a miniature and concentric circle electrode system that is capable for highly accurate rotation and modulation even at radial modulation rates or wave forms.
-
Product
Three-Phase Converters
SIRIO 3PH 7 ALFA 3PHSAP
-
The three-phase converter is an electronic equipment able to vary the RMS value of a sinusoidal voltage by controlling no. 6 controlled, antiparallel-connected conducting diode pairs.Since the wave form is symmetrically split both into positive and negative halfwave, the output voltage average value is not affected and equal to zero. This means that three-phase loads can be fed without gene rating inside the mesh a circulating current with average value other than zero.Moreover, the three-phase converting is obtained with only one control circuit thus ensuring balance between the three linked voltages applied to the load.
-
Product
Form Testers
-
The highly accurate rotary table machines and spindle form testers of the RONDCOM series can be used in many areas: production, measuring room and calibration lab.
-
Product
Wave display utility
GUI
-
GUI allowing users to view and analyze test vectors in all common formats (VCD/EVCD/WGL/STIL).
-
Product
Plane Wave Converter
PWC200
-
The R&S®PWC200 Plane Wave Converter is a bidirectional array of 156 wideband Vivaldi antennas placed in the radiating near field of the device under test (DUT). The phased antenna array can form planar waves inside a specified quiet zone within the radiating near field of the 5G massive MIMO base station for realtime radiated power and transceiver measurements (EVM, ACLR, SEM, etc.).
-
Product
Wave Profiler
-
The Wave Profiler allows the user to measure non-directional wave parameters continuously for long periods of time with high temporal and spatial resolution in deeper water from the safety of an underwater mooring. The instrument is particularly useful for clients who need to measure long-period waves (such as rogue waves or infra-gravity waves), waves in wash and in wakes, and non-linear waves.
-
Product
Full Wave Recorder
V-FullWaver
-
The V-FullWaver systems were specifically developed for precise full waveform time domain Induced Polarisation, Resistivity and SP measurements. Each system is fully independent; incorporating its own power source, GPS module and digital memory for up to 3 months continuous recording.
-
Product
Wave Profiler Fixture
KIC® Wave Surfer™
-
The KIC Wave Surfer is a self-contained system that provides critical data on wave solder machine set up and performance. Used in conjunction with your SlimKIC 2000 and the KIC 2000 software, you can ensure your wave solder machine is set up and performing properly.
-
Product
Mm Wave Measurement
Erickson PM5B
-
bsw TestSystems & Consulting AG
Erickson PM5B from VDI, which has been further optimised in the version just presented. The measuring head of the PM5B operates in the WR10 band, i.e. in the 75 - 110 GHz range. High-precision accessories, so-called tapers, provide for adjustments and thus make measurements in the waveguide bands, currently up to WR0.34 beyond 3 THz, possible.
-
Product
Motion Based Waves
-
Accurate Motion Based wave measurements are critical in applications such as offshore wind farm development, navigation, cable laying, breakwater building, and bridge construction.Waves also result in continuous loads on marine structures, including docks, moorings, and offshore platforms.Motion Based Waves are challenging to measure. Variables to consider when collecting wave data include the depth of the measuring device, proximity to shore, wave types, and available infrastructure from which to measure.Several methods for measuring motion based waves are available, and careful selection of the best approach is needed to get the optimal result.
-
Product
Millimeter Wave Amplifiers
-
Ducommun offers Low Noise (ALN), High Power (AHP), Full Waveguide Band (AFB) and General Purpose (AGP) amplifiers to cover the frequency range from 18 to 96 GHz. These amplifiers utilize thin-film and microelectronics manufacturing techniques and are discrete and/or MMIC PHEMT devices based. These amplifiers feature low noise, high output power, single DC power supply and wide operation temperature range. The amplifiers are offered in two categories, standard and custom-built. Both standard and custom-built amplifiers are equipped with various RF interface, including standard waveguide or coaxial connector for convenient system integration. The optional input and output integrated isolators are available as an option to further improve the port return loss.
-
Product
Sentinel V Waves Array
-
Teledyne Marine RD Instruments
Teledyne RD Instruments Sentinel V Waves Array combines our highly robust, field-proven WavesMon processing with our new 5-beam Sentinel V ADCP to provide the highest-quality waves and current profiles of any ADCP in use today.
-
Product
Combination Wave Generator
-
Shanghai Guantu Technology Co., Ltd.
GCW series combined wave generators can generate high energy surges for combined wave testing. It has the characteristics of fast rise and long pulse duration. According to different modulation components, different surge waveforms can be generated; the control system can automatically record and analyze the above surge waveforms. standard:IEC60060-4-5, IEC61643-11, UL1449-2006, GB18802.1, GB/T18802.21,
-
Product
Small Form Factor
-
Whether it’s a military UAV, ground mobile, naval or other deployed environments, our innovative and intelligently designed platforms are based on our extensive packaging expertise. With a focus on Size, Weight and Power (SWaP) our SFF platforms are engineered with multiple configuration options providing maximum performance.
-
Product
Wave Buoy
MOTUS
-
The MOTUS (movement in Latin) Wave Buoy is a perfect solution for collecting environmental data in coastal areas.Collect reliable environmental data with MOTUS Wave Data Buoy.The MOTUS (movement in Latin) Buoy is a perfect solution for collecting environmental data in coastal areas for all-year deployments. The platform used for collecting data is a robust buoy which has proven to be an excellent platform for providing high accuracy and reliable meteorological and oceanographic data. The wave buoy can effectively combine various Hydrological and Meteorological parameters. Basic parameters such as wind, waves, and currents can easily be expanded to include sensor packages with different water quality sensors. Data is controlled and synchronized by the data management systems that Xylem Analytics offers, which also controls and powers real-time communication. This provides a low-power efficient system offering long-term deployment capabilities.The MOTUS Wave Buoys combine our ultra-low power and field-proven solutions from developing oceanographic and water quality sensors. We have 60 years of experience operating in the industry, providing you with an optimal platform based on the buoy, a rugged, lightweight polyethylene buoy deployed in more than 40 countries all over the world. By selecting Xylem as your partner in your projects, you are on track for the lowest overall cost of ownership and a versatile platform that can be tailored to your needs. The MOTUS Buoy is developed for both scientific and commercial use.
-
Product
Millimeter Wave Products
-
Reliable Millimeter-Wave High-Power Products for Airborne, Maritime and Ground Mobile Deployment
-
Product
Small Form Factor (SFF)
-
The modular design of the Mini ATR platform allows for various configurations. The chassis can easily be scaled up or down while using the same side walls. DC and AC power variations as well as custom front I/O configurations are available. Elma also offers a wide selection of backplanes in various architectures and has different milled card cage sizes off-the-shelf.
-
Product
RF Detectors for Millimeter Wave
-
RF Detectors are essential microwave/millimeter wave products for most Tx (transmit sources). Transmitter output power measurement is the main application. It is essential to know the RF output power because the output power level must not go above values set by FCC regulations.The unit of power is the watt for RF detectors. But, most commonly used in most RF and wireless systems to express power is the terms of dBm or decibels related to 1 mW:View more RF Detector
