Showing results: 886 - 900 of 6611 items found.
-
Extech ET20 -
Extech Instruments Corporation
The ET20 is a Compact Dual Indicator Voltage Tester. 100 to 250V AC/DC volt detection. Probes snap on housing for easy one-hand operation.
-
GT00YA00ZX -
GAO Tek Inc.
The GAOTek Portable H/L Voltage Clamp Current Leaker measures high voltage current with a 12.5 in (32 cm) insulating rod, adopting the latest CT technology and integrating mask digital technology. This instrument provides high precision, reliability, and stability with its integrated design between transducer clamp and domain. This leaker can be used to measure any wire with or without the insulation layer where the voltage is below 10 kV. The insulating rod is portable, moisture resistant, heat resistant, shock resistant, and insulating. It provides additional functionalities such as online current testing, peak and data holding, data storage, detection of high and low current in primary and secondary circuits separately, and provision of suitable calculations to conclude change in high and low pressure.
-
GF303D -
Beijing GFUVE Electronics Co.,Ltd.
The GF3031 is a powerful and portable three phase current and voltage source. All test values are generated absolutely synthetically with a high degree of accuracy and stability. The source is available in 12 A, 24A or 120 A.The GF303D three phase portable power source is a lightweight and portable current and voltage source based on newest technology and serves for solving this problem by simulating the required load conditions. Operation is performed by integrated 7" touch screen or via keyboards
-
CMTI-8010A -
High Power Pulse Instruments GmbH
The CMTI-8010A is a high voltage 50 Ω pulse generator for static and dynamic common mode transfer interference (CMTI) evaluations of digital isolators according IEC-60747-5-5 and IEC-60747-17.
-
CMTI-8010C -
High Power Pulse Instruments GmbH
The CMTI-8010C is a high voltage 50 Ω pulse generator for static and dynamic common mode transfer interference (CMTI) evaluations of digital isolators according IEC-60747-5-5 and IEC-60747-17.
-
DM3420 -
Labfacility Ltd.
The DM3420 panel meter accepts Voltage and Current process signals and displays the process value on a high efficiency daylight readable LED display. A built in transmitter power supply is also provided.
-
Cambridge Instruments & Engineering Co.
suitable to perform AC High Voltage Power Frequency test on transformers, motors, cables etc. Leakage current can be measured at desired pressure and this set can be used as a source for cable fault burning.
-
HV-43 -
Klein Tools, Inc.
Used for checking voltage up to 1,000V AC.Connects to the hot stick end of the High-Voltage Contact Tester (Cat. No. HVCT1).Dielectric pole type-tested & rated for 10kV AC.Comes in a convenient zippered pouch.
-
SCR ELEKTRONIKS
Every electrical apparatus or machine consists of two distinct sections - one which carries the electricity, and other which is isolated (insulated) from the electric currents. The former may be called the `Live' side whiles the latter `Earth’ side. A person near about the apparatus or handling it can safely touch the Earth side, but not the live side, for obvious reasons. To ensure that the isolation of the two sections is effected properly, the apparatus is tested by subjecting it to a Voltage much higher than the normal working Voltage. If the insulation is good, it stands the test without breakdown otherwise high electrical stress punctures the insulation at its weakest spot foretelling a later calamity to unwary user. Government Department- when buying electrical equipments- and all reputable manufacturers test every piece of equipment by this test called HIGH VOLTAGE TEST. It weeds out poorly insulate apparatus.
-
PPE6KV-A -
Teledyne LeCroy
High voltage single-ended passive probes are suitable for a wide range of applications where ground-referenced high-voltage measurements must be made safely and accurately. There is also a sense pin to automatically configure the oscilloscope for use with the probe.
-
Technology Products
This Compact power supply/test set can perform all laboratory and field tests of DC Hipot. A flexible High Voltage Cable is provided at the back for connecting to the test specimen. Available in Rack Mount as well as portable design.
-
2340 -
TEGAM Inc.
The Model 2340/2350 High Voltage Amplifier expands the amplitude range of any standard, 50 function, pulse, or waveform generator to 400 volts p-p. Model 2340/2350 comes standard with a fixed gain of +50, and gains from 10 to 100 are available as special order.
-
1969 -
Peaceful Thriving Enterprise Co Ltd
*With cUL and RoHS Approval.*Check voltage on 100-600V AC.*Two LR44, 1.5V batteries which is included.*Audible and visual indication for easy operation.*Four-section power and sensitivity switch (H, L, M and off).*Locates breaks along live, insulated wires and power cords.
-
Technology Products
HV Testing Kits are used for testing of Motors, Generators, Switchgears, Cables, Transformers and other electrical equipment. These are used for testing & commissioning of HV electrical equipment. High Voltage AC Testing Kits are available in ratings from 25KV to 300KV AC in various mA and KVA Ratings.
-
HVD3220 -
Teledyne LeCroy
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.