Showing results: 16 - 30 of 33 items found.
-
ELCOLEVEL - Software For 3D-straightness Measurement -
Optik Elektronik Gerätetechnik GmbH
ELCOLEVEL is a software with interfaces to electronic autocollimators and inclination levels of different manufactureres. This allows for example the 3D-Straightness measurement (twist-, roll- and yaw-angle) of slides in one and the same measuring procedure.
-
HW Test
REBOUNDER test kits feature two separate "Co-Active Seals", "Quick Twist" Locking Guide Pins, and boards constructed of fine weave G10/FR4, increasing testing reliability and accuracy while simplifying finishing, debugging, and maintenance.
-
Omega Engineering, Inc
Connectors used for pressure and force sensors. Includes cable assemblies for pressure transducers and load cells, DIN connectors, twist lock connectors, push on connectors, and dynamic sensor cables.
-
TRI -
HW Test
REBOUNDER test kits feature two separate "Co-Active Seals", "Quick Twist" Locking Guide Pins, and boards constructed of fine weave G10/FR4, increasing testing reliability and accuracy while simplifying finishing, debugging, and maintenance. All H+W products are backed-up with our "Test-Assured" one year warranty, in writing, and SAME DAY SHIPMENTS
-
Dongguan Lixian instrument scientific co.,LTD
Leather torsion resistant testing machine is used to test the folding nature for various leather and fabric.The machine used to test the folding nature for various leather and fabric, Materials need be nipped both inside and outside, Twist and turn over and over again until a certain number, Observe the damage of the tested materials, this machine applied to use in clothing, shoes, bags and other thin material leather.
-
DP750-100 -
Shenzhen Micsig Instruments Co., Ltd.
*The leads and probe are with shielded design, interface ends are integrated in a compact box, no need to twist the cables, leads to a lower noise floor and has less interference. *Support one-press Zero calibration and automatic overrange alarm.*Directly powered by Micsig UPI interface, realise auto scaling setup, can also powered by oscilloscope via USB cable.
-
FEINMETALL GmbH
FEINMETALL offers a wide range of contact probe:ICT / FCT probes, short travel probes, double plunger probes, fine pitch probes, interface probes, wire harness probes, threaded probes, high current probes, switch probes, twist proof probes, push back probes, koaxial probes, radio frequency probes.
-
DAFM3B -
UEi Test & Measurement Instruments
The DAFM3B Anemometer/ Psychrometer meter is designed with 6 HVAC/R must have parameters in one instrument. These are included in a portable battery operated instrument for measuring humidity, air temperature, dew point and calculating wet bulb, air velocity and air volume. The sensor is built into the remote fan and is specially protected by a twist cap. While in operation, open the cap for accurate temperature and humidity readings.
-
FanZ -
Zeus Numerix Pvt. Lmtd.
FanZ designs efficient high aspect ratio blades for axial fans. For the required head & flow conditions, FanZ calculates the span-wise variation of chord length & twist of the most optimal sectional profile. The software also predicts the off-design-performance and structural robustness of the blade. The output is in the form of ready to manufacture DXF format drawing files. More than a dozen customers use FanZ for the design of their cooling tower fans.
-
TG 20/50 -
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR TG 20/50. The TG 20/50 is a portable, battery-operated audio generator with a built-in charging unit. Together with the UL audio frequency receiver and the SP detecting rod, the TG 20/50 is used for cable tracing, twist method and for determining the depth of cables and metal pipes.* Automatic or manual impedance adjustment* Charging unit and rechargeable battery integrated; battery or mains operation* Continuous or cyclical output* Two output frequencies selectable
-
TG 600 -
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR TG 600. The TG 600 audio frequency transmitter was designed specifically for the precise location of cable faults and joints using the twist method. The display of the input and output current makes selection of the correct adjustment easier.* High-performance audio frequency transmitter up to 600 VA* Frequency of 2 or 10 kHz, quartz-stabilised (other frequencies on request)* Potential-free output* Impedance adjustment in 8 steps from 0.3 to 300 Ω
-
Flex-US -
SDT Ultrasound Solutions
The design of the Flex.US is based on the popular "Flexible Sensor" from SDT. Mounted on the end of a flexible steel pipe, the ultrasound sensor can access any hard-to-reach location. Bend, twist and curve your Flex.US to suit your inspection. Safely scan electrical cabinets and behind machinery guards without putting your hands in danger. To ensure comfort, the volume control is quickly adjusted when very loud ultrasounds are encountered. This sensitivity provides a high level of precision making leak detection a pleasure, not a chore.
-
A2B®-Component-Tester -
NOFFZ Computer Technik GmbH
The Automotive Audio Bus (A²B®) is a bus developed by Analog Devices Inc. for infotainment systems in automobiles. It is increasingly being used in other applications such as AV conferencing systems. Typical A²B® -products are Hi-Fi amplifiers/speakers, head units, eCall systems, microphones, vibration/noise suppression units, actuators, or sensorsCommunication happens via a simple two-wire UTP (Unshielded Twist Pair) cable. All A²B® -components are connected in a master/slave architecture to form a network. The complexity of audio systems in these A²B® -networks is reduced, and with it the cost and weight.
-
Aero Nav Laboratories, Inc.
The terminal strength test is used to performed to determine whether the design of electrical terminals and their method of attachment can withstand mechanical stresses to which they will be subjected during installation or disassembly in equipment. These stresses must be withstood by the component without sustaining damage which would affect either the integrity of the terminals or the operation of the component part itself. Procedures are established in this method for testing, for example wire-lead terminals, flexible-flat-strip or tab-lead terminals, and rigid-type terminals which are threaded or have other arrangements for attaching conductors. The forces applied during the test consist of direct axial, radial or tension pulls, twist, bending torsion, and the torque exerted by the application of nuts or screws on threaded terminals.
-
MemoRail Modbus A1405 -
ALVI Technologies
With the increasing demand for a compact and flexible solution to liquid analysis –ALVI Technologies has responded with a new twist in the existing MemoRail. We are pleased to announce the release of our new MemoRail Modbus A1405 N- Dual Channel Multiparameter Analyzer with Modbus that offers an optimal solution for integrating a compact, flexible, all digital analyzer in an extremely cost-effective manner!! Our Dual Channel Multiparameter Analyzer with Modbus can be used with Memosens and digital sensors such as pH (glass and IsFET), ORP (redox), oxygen, and conductivity (conductive and inductive). It’s also the only analyzer in its class that is suitable for use with a digital optical oxygen sensor. All sensor types can be used in any combination in the dual-channel version.