Torque
turning force.
See Also: Torque Sensors, Torque Testers, Torque Transducers, Torque Meters, Dynamometers
-
product
Digital Strain Gauge Sensor
ZET 7110
The ZET 7110 module is intended for measuring the relative deformation using primary transducers based on tension gauges. These may be either assembled tension gauges (force gauges, torque gauges), or detachable tension gauges connected using half-bridge or bridge mode.
-
product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
780264-02
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
product
AWD Dynamometer
MD-AWD-150 Series
Full time AWD vehicles are designed to provide maximum performance regardless of road conditions. In cases where traction is less than ideal, a vehicle may be designed to improve stability and traction at the expense of power. This means adding torque to a spinning wheel or retarding of timing. In order to properly test an AWD vehicle for peak performance, an AWD chassis dynamometer must be able to simulate ideal road-load conditions to the vehicle.
-
product
Torque Gauges and Test Stands
SHIMPO offers a torque product line that is suited for accurate and precise testing.
-
product
Prop Shaft Torque Measurement Systems
Advanced Telemetrics International
ATi Telemetry Systems are typically used to transmit data from rotating shafts or machinery to a stationary receiver. The Miniature Strain Gage Transmitter can be attached to strain gages adhered to your shaft in order to transmit shaft torque and thrust while the system is running.
-
product
Economy Mechanical Calibration Kit, DC To 26.5 GHz, 3.5 Mm
85052D
The Keysight 85052D economy mechanical calibration kit contains precision standard devices to characterize the systematic errors of Keysight network analyzers in the 3.5 mm interface. This kit also contains adapters to change the gender of the test port and a torque wrench for proper connection. Connector gauges may be ordered separately.
-
product
Vibration-Rotation Excitation Bench
·Realizing rotation-vibration excitation operation suitable for vibration test of gear, endurance test of engine accessory·Rotation-vibration excitation operation equivalent to engine vibration excitation1 Reproducing rotation speed fluctuation and torque fluctuation2 Reproducing engine explosion fluctuation3 Reproducing waveform in engine starting·Environmentally friendly compared to the engine bench1 No need for fuel system facility2 No need for exhaust gas treatment3 No need for taking fire prevention measures
-
product
Torque Sensors
To improve your product quality and lower your product loss rate, try Mountz torque sensors. Whether you need laboratory-grade precision to measure hand tool output in inch-ounces or the durability to handle frequent pneumatic tool testing in the foot-pound range, Mountz has the right torque sensor for your application. In-line rotary torque sensors even allow you to directly measure the torque a power tool applies to an actual fastener, giving you the most accurate measurement possible. Designed for ease of use, Mountz torque sensors are plug and play, helping technicians get right to work and minimizing the chance of error.
-
product
Torque Testing
Torque testers measure properties such as torsional strength and stiffness and are used in quality control of various fields including medical devices, metals, and aerospace
-
product
Adjustable Break-Over Wrench
ATB
The ATB is adjustable torque wrench suitable for a variety of applications across multiple industries from aviation maintenance to general repair tasks. The wrench has the ability to change head configurations like open end, box, flare or a ratchet head. At the set torque, the handle moves through an angle of 20° before resetting.
-
product
Digital Torque Meter
TS-2800
The TS-2800 is a torque meter for phase difference type torque detectors. Can be used with our long-selling torque detectors SS/DD series and high accuracy, high response type TH series. Since all signals are digitally processed, torque measurement can be performed with great stability, reproducibility and linearity.
-
product
Torque Instruments
Advanced Force & Torque Indicator
Used with a range of 'plug and play' torque and force sensors - ideal for 'static' or 'dynamic' (rotary) torque measurementCan be used as part of a Mecmesin test system or mounted to one of your own test rigs
-
product
Force Sensors
Here at Flintec, our force sensor range provides solutions that integrate effectively into a wide variety of industrial applications. They include customized load pins, extensometers, torque sensors and a range of miniature force sensors.
-
product
Engine Dynamometer
H3608
Power: 6,400 hp (4,772 kW)Torque: 37,348 lb-ft (50,658 Nm)Speed: 2,500 rpmInertia Value**: 1,575 lb-ft2 (66.37 kg-m2)Shipping Weight: 14,000 lb (6,350 kg)
-
product
Fuel Flow and Torque Converter
Model 44SM1
This self-contained, remotely mountable Second Harmonic Fuel Flow Interface accepts data from a second harmonic fuel flow transmitter then converts this information into a frequency output proportional to fuel flow. In addition, this module will accept signals from a T56 Torque Tranducer and provide a DC voltage proportional to Torque. Typical application is for use with Flight Management and Nav Management Systems. The use of field proven designs and carefully selected components assures high reliability field performance.
-
product
Precision Mechanical Calibration Kit, DC To 26.5 GHz, 3.5 Mm
85052C
The Keysight 85052C precision mechanical calibration kit contains precision standard devices to characterize the systematic errors of Keysight network analyzers in the 3.5 mm interface. This kit also contains adapters to change the gender of the test port and a torque wrench for proper connection.
-
product
Electric Servo Motor Type 2 · 4 Poster Vibration Tester
It arranges four 3-axis vibration testers equipped with a high torque, ultra-low inertia servomotor to test the vibration of the finished vehicle.
-
product
PTO Dynamometers
AW is the world leader in AG/PTO dynamometers with over 14,000 units sold. AW's hydraulic activated load unit is water cooled allowing it to test high torque loads for continuous periods of time. AW's heavy duty load units are well known to last for decades. Combine this with all new computerized electronic load control, software, thermocouples, sensors and you have a system second to none - the AG.X Series.
-
product
Motorized dynamic torque bench
TORKHEADRIVER
The TorkHeaDriver is a motorized torsion tester that is equipped with a rotary torque sensor allowing torque and angle measurements on complete system. This torsion meter is particularly well suited for measurements on knobs, valves, faders… installed on sets.
-
product
Engine Dynamometer
DS46-HS
Power: 2,125 hp (1,584 kW)Torque: 7,125 lb-ft (9,660 Nm)Speed: 4,000 rpmWater Use*: 147 gpm (556.5 lpm)Inertia Value**: 172.4 lb·ft2 (7.3 kg·m2)Shipping Weight: 2,860 lb (1,297 kg)Rotation: bi-directional*No Cooling System** With Companion Flange or Torsional Coupling
-
product
Small/Medium Capacity Torque Detector
SS series
The SS series torque detector suits to wide variety of torque measurement application, including performance test of motors, pumps, compressors, blowers, turbines and gears. High rigidity results from the unitized cast-casing structure and SS series torque detector can be handled easily as being free from parts replacement on treatment of maintenance, comparing to other type of torque detector such as strain gauges, with non contact signal detection on the detector. 13 models in the series can be provided and chosen among them according to requirement in torque capacity.
-
product
Pressley Fiber Bundle Strength Tester
F215
To determine the tensile strength of natural fibers. Includes 1 pair clamps and spacer, torque vice and wrench, cutter, comb and tweezers. A 5mg x 0.01mg capacity balance is required but not included.
-
product
Rotary Actuators
Electrical rotary actuators with rated torque of 100 Nm ... 16000 Nm for the operation of final control elements with preferably 90° rotary movement such as flaps, cocks, dampers, etc.A lever / linkage bar assembly transfers the torque or the actuator is directly coupled to the cock flange.
-
product
Rotating Torque Meter
NTS-6 series (S1/S2/S5/S10/S20)
Torque measurement of rotating body. Measure rotational torque during assembly of devices with rotating functions and on finished products. While the output shaft self-rotates, the built-in sensor catches load fluctuations on the rotating body. It is possible to measure the rotation starting torque of the rotating object ( which does not rotate by itself and does not have power) and the load torque during rotation. (Printers, copiers, zoom lenses, door knob mechanisms, hinge mechanisms, etc...)
-
product
Vector Magnetometer
10 VSM
The Model 10 Mark II VSM is the state of the art in VSM magnetometers. Its sensitivity and accuracy surpasses all other commercial vector magnetometers. Its field range and resolution make it the ideal system both for high and low coercivity materials. The accuracy in the determination of the magnetization vector, together with the high sensitivity, makes this the first VSM that can be a real alternative to a torque magnetometer for anisotropy studies on modern recording materials.
-
product
Power Monitoring Dynamometer
90085
Model 90085 is designed to measure machine tool output. This model acquires the necessary torque and speed data needed to calculate the horsepower of the machine tool under test conditions. It is a portable, self-contained data acquisition and monitoring system consisting of three major components: a pneumatic brake assembly, a torque and speed transducer, and the control and display module.
-
product
Vertical Dual Display Spring Torsion Testing Machine
Model TNS-S-L Series
Jinan Testing Equipment IE Corporation
This series of testing machines is mainly applicable for testing the torsion angle and torque of various kinds of small-sized torsion springs, coil springs, elastic components and other friction structures.
-
product
Computery Control Torsion Tester
SG-L10
The machine is mainly used for torsion test of metal and nonmetal,also it is applicable to the torsion test of parts and members. Servo-motor and cycloid gear reducer are introduced to the loading system in this product, the system for measuring torque and distortion angle are composed of high accurate torsion sensor, photoelectric encoder and computer measuring force.It possesses automatically tracking test torque and distortion angle, maintaining maximum peak load and displaying loading speed....show more -
product
Plate Rheometer
DVNext Cone
The DVNext Wells-Brookfield Cone/Plate Rheometer is a precise torque meter which is driven at discrete rotational speeds. The torque measuring system, which consists of a calibrated beryllium-copper spring connecting the drive mechanism to a rotating cone, senses the resistance to rotation caused by the presence of sample fluid between the cone and a stationary flat plate.
-
product
Rotary Hex Drive Torque Sensor
Futek Advanced Sensor Technology, Inc.
The Rotary Hex Drive Torque Sensor category has Torque Sensors which are used in slip ring and non contact rotary torque measurements. The most common utilization for these models is for inline/reaction applications, where measurements can be made in both clockwise and counterclockwise directions.
