Filter Results:
Products
Manufacturers
Applications
Timing
See Also: Time, Timers, Time Interval, GPS Time, Time Reference, Time Code, Time Domain, Time Standards, Time Interval Analyzers
-
Product
Time Domain Reflectometer
STEP TDRS
-
Cable Measurements: Distance, Fault Types, Distance to Faults, Impedance Readings, and Loop Resistance.
-
Product
PC-Based Time Interval Analyzer
GT658PCI
-
GuideTech’s GT658PCI is an ultra-fast, high resolution, DC – 400 MHz Time Interval Analyzer (TIA), ideal for most PC-based lab bench (timing) test applications. What makes the GT 658 superior to traditional counters is analogous to the difference between volt meters & digital scopes. While both measure voltage, the scope provides much more information about the dynamics of the signal. This is because our patented TIA substantially increases measurement speed, and the measurements are displayed as afunction of time. All of these features, along with the benefit of ‘continuous time correlation to a common reference between all measurement time stamps,’ enable our TIAs to make measurements that weren’t previously possible with traditional counters.
-
Product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
784776-01
Signal Module
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
Product
Wattmeter
PowerMaster II for SO2R
-
The Power Master II wattmeter has the ability to have two couplers connected to it, and it has provision to allow switching very easily between the two couplers through only two button presses on the front panel.When operating SO2R, you do not want to have to toggle from one coupler to another. We make matched couplers available for SO2R users and due to the nature of these couplers being high impedancedevices, we can actually connect the two coupler inputs in parallel and instead of toggling between the two couplers, they will both be connected and active at the same time. The first step is to disconnect all connections to the rear panel of your Power Master II and remove the two #6-32 philips screws on either side of the cabinet.
-
Product
Analog Ultrasonic Detection System
ULTRAPROBE 2000
-
Designed for ease of use, it often takes no more than 15 minutes to become competent in testing with the ULTRAPROBE 2000 Kit Complete. Fast accurate diagnosis through the ULTRAPROBE 2000 System will dramatically reduce unplanned down time and shorten planned outage time.
-
Product
Xenotest Beta+
FD
-
Atlas Material Testing Solutions
The Xenotest Beta+ FD is a premium stand-alone rotating rack xenon instrument with a 4000 cm2 exposure area. This instrument is specifically designed to meet the testing needs of the FMCG industry, such as drinks, foodstuffs, personal care and household products. The Beta+ FD enables consumer goods manufacturers to test their products realistically within very short test times, typically with acceleration factors between 10-50 times faster than real time.
-
Product
PXI-5154, 1 GHz, 2 GS/s, 8-Bit, 256 MB/ch, PXI Oscilloscope
780319-03
Oscilloscope
1 GHz, 2 GS/s, 8-Bit, 256 MB/ch, PXI Oscilloscope—The PXI‑5154 is ideal for acquisition and characterization of fast, nanosecond-edge speeds. It is well-suited for automated test and data streaming applications in the consumer electronics, semiconductor, aerospace/defense, and life sciences industries. The PXI‑5154 also comes equipped with up to 256 MB of memory per channel to provide high, sustained sample rates over extended data capture windows. This digitizer, optimized for automated test, uses a high-throughput bus to lower test times, provides picosecond-level synchronization among modules, and integrates with the entire suite of NI hardware, so you can build and customize a complete mixed-signal or high‑channel‑count test system.
-
Product
Beam Panoramic Power Supply Battery Crawler 40 to 160 kV
CP160CR
-
Designed to fit into 6” pipelines and higher, the CP160CR constant potential X-Ray generator for crawlers is – in its category – the most powerful panoramic X-Ray tube head in the world for crawlers. The generator is making the cutting edge constant potential technology of the CPSERIES even more compact into a 9.9 kg – 120 mm diameter X-Ray tube head. The crawler unit is capable of penetrating up to 28 mm of steel in 10 minutes, which corresponds to just a 25 second exposure time for 6” standard pipeline welds.
-
Product
Handheld TDR
-
The handheld Time Domain Reflectometer (TDR) consists of CM Technologies’ PCI-3127 high-performance metallic TDR card packaged in a rugged handheld computer form factor. The software interface uses an easy to follow menu structure to assist in acquiring, saving and interpreting TDR signatures – extremely flexible when compared to traditional instrumentation.
-
Product
PCI to PMC Adapter / Carrier
PCIBPMCx2
-
Embedded applications frequently require real time processing coupled with special purpose IO. With the PCIBPMCx2´s two slots; a PrPMC can be matched with another PMC to make a high bandwidth processing node. The PrPMC can communicate with the host for set-up, and then use the local bus to control and transfer data with the special purpose IO card.
-
Product
Linear Detector Arrays (LDAs)
X-Scan H
-
This digital end-to-end solution is built on a proven concept enabling easy integration, and accelerated development time of X-ray systems. X-Scan H series has high radiation hardness extending lifetime of detectors significantly, and reducing total costs. The series is available in several standard lengths easily scalable to various configurations.
-
Product
Digital Automated Fiber & Ferrule Interferometer For Single Fiber Connectors
DAFFI SF
-
The latest interferometer from Data-Pixel is a cost effective solution for high volumes production, without compromising on accuracy or performance. Based on our extensive interferometer manufacturing experience we designed the DAFFI SF to be robust, fast and accurate in order to meet all manufacturing or laboratory environments. With the Blink software platform, DAFFI is able to measure the end face geometry on single fiber connectors in a very short time. The Daffi interferometer accessories (flange and adapters) are fully compatible with the Daisi range, allowing the user to limit the costs of the 3D geometry measurement units.
-
Product
Isolated Watchdog Board
APCI-035
-
The board ADDIMULTI APCI-035 is equipped with 4 watchdogs allowing the simultaneous monitoring of multiple processes. Watchdog N? 1 works with 2 alarm levels and can be set to 1 of 4 different time bases (µs, ms, s, min). Level 1 alarms the PC cntrol and/or the monitored device. Level 2 resets the PC and/or the monitored device after a defined time. The alarm control can be accessed through 1 trigger channel and 4 different time bases.
-
Product
Safety Laser Scanner Type 3
SD3-A1
-
Panasonic Industrial Devices Sales Company of America
The Panasonic SD3 Safety Laser Scanner is a cost-effective alternative for guarding danger zones. It can be used flexibly in confined spaces and for areas where the danger zone changes.The SD3 can monitor an area within an angle of up to 190° and divides it into 2 zones: a warning zone within a radius of 15m, and a protection zone within a radius of 4m. The contours of these zones can be configured precisely for any application. Up to eight zone patterns can be set and activated at any given time even during operation.The reference boundary function memorizes the position of stationary objects and establishes a virtual boundary. It also monitors beam alignment after installation and issues an alarm if a beam becomes misaligned.
-
Product
IDM+
-
Multi-functional fault recorder including: -- Disturbance fault record (DFR)- Dynamic disturbance recording (DDR) - Phasor measurement unit (PMU C37-118)- Power Quality (PQ Class A)- Travelling wave fault location (TWS to +/-60m) - Impedance fault location- Protocols (61850, Modbus, DNP3) - Sequence of event recording (SOE)- GPS, IRIG and NTP time sync- iQ+ masterstation software.
-
Product
Designer 2.0 Vision Software
-
Cognex Designer is an integrated development environment for 2D multi-camera and 3D vision applications. Creating machine vision applications has become increasingly complex over the years, and Cognex Designer provides the tools for breaking down the complexity into manageable tasks in order to complete vision projects successfully in a shorter period of time.
-
Product
Intergrated Multi-Function Controllers
-
Watlow Electric Manufacturing Company
Watlow''s integrated multi-function controllers decrease design and assembly time, require less space, minimize system complexity and best of all, lower the total cost of ownership.
-
Product
PXI-8512, 1‑Port, High-Speed, Flexible Data Rate PXI CAN Interface Module
780687-01
CAN Interface
1‑Port, High-Speed, Flexible Data Rate PXI CAN Interface Module—The PXI‑8512 is a high-speed Controller Area Network (CAN) Flexible Data-rate (FD) interface for developing applications with the NI‑XNET driver. The PXI‑8512 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
Circuit Breaker Tester
GDGK-303
-
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
1) Closing and opening time measurement of 12 channels2) Max difference of closing or opening time measurement of three phases3) Bounce time and frequency measurement of breaker closing4) Circuit breaker closing and opening speed measurement5) Travel-time, Coil current-time curve of circuit breaker operation measurement6) Clearance of circuit breaker measurement7) Variable DC circuit breaker operation power supply8) Print test results by internal micro printers
-
Product
DDR5 Logic Analyzer
FS2602
-
The FS2602 is our the latest logic analyzer probe used to test DDR5 SO-DIMM memory. It is designed to work exclusively with 4 Keysight U4164A logic analysis modules operating in either Quad Sample State or Quarter Channel 10GHz timing modes. This gives the user an extremely effective tool for debugging, testing and verifying DDR5 SO-DIMMs running at ~4000MT/s.
-
Product
Power Supplies
I-400
-
The I-400 power supplies are durable, practical, and efficient. Remove all superfluous attachments and features. The I-400 can provide reliability and 400 watts of power you can depend on to run your system. With its 80mm silent cooling fan designed for fastest cooling time and minimal noise level; you won't have to worry about overheating and noisy fans anymore. This is the basic power supply for casual users who just needs something that is cost effective and works.
-
Product
Image Processing and Analysis Software
ENVI
-
L3Harris Geospatial Solutions, Inc
ENVI is the industry standard for image processing and analysis software. It is used by image analysts, GIS professionals and scientists to extract timely, reliable and accurate information from geospatial imagery. It is scientifically proven, easy to use and tightly integrated with Esri’s ArcGIS platform.ENVI has remained on the cutting edge of innovation for more than three decades due in part to its support of all types of data including multispectral, hyperspectral, thermal, LiDAR and SAR. ENVI makes deep learning accessible to people through intuitive tools and workflows that don’t require programming. ENVI geospatial image analysis can also be customized through an API and visual programming environment to meet specific project requirements.
-
Product
Coil Analyzers & Power Supplies
-
Coil analyzers and power supply units are portable and lightweight devices intended for use in harsh switchyard and industrial environments. The typical application is switchgear and circuit breaker testing when substation battery is not connected or available. An advantage over substation battery is enabled testing in under-voltage and over-voltage conditions. Furthermore, the stable voltage outputs with a very low ripple (<0,5%) enable an analysis of the coil and motor current graphs recorded with circuit breaker analyzers from different vendors.SAT40AD, POB30AD, and POB40AD are unique devices in the market due to their dual purpose:Power supply for coils and spring-charging motorsTesting circuit breaker’s coils, motor, and auxiliary circuitAll DV Power coil analyzers and power supply units have four separate outputs for opening and closing coils.SAT40AD has two powerful motor outputs (AC and DC) which can withstand up to 40 A inrush current.POB30AD and POB40AD have DC motor output rated up to 30 A and 40 A respectively. With the use of motor outputs, POB and SAT can also be used as a power source or a temporary battery charger.SAT40A II series instruments can be controlled via PC. The DV-Win application software is used to control both SAT and CAT (Circuit Breaker Analyzers & Timers) devices at the same time, making a unique test system for switchgear and circuit breaker testing.
-
Product
Self-Contained Metering Site Training Bench
Model 8813
-
The PowerMaster® 8813 is a true 3-phase training simulator for metering technicians to help improve their troubleshooting skills for applications encountered in the field. The Model 8813 provides a safe, controlled environment to help the trainee accelerate their education in meter testing and wiring verification. The training simulator also features the ability to simulate over 28 commonly found metering errors in the field. Paired with the Training Administrator Station (TAS), the bench can be controlled remotely over a closed WIFI network, and each trainee’s performance is recorded and time stamped for every session.
-
Product
Software
Gate Oxide Integrity Option
-
Materials Development Corporation
Oxide integrity of MOS devices can be evaluated by various techniques such as Time Dependent DielectricBreakdown, Charge to Breakdown, or ramped voltage. When used with a prober, map distribution of breakdown fields. Output the data using histograms, cumulativefailure, or Weibull plots.
-
Product
Temperature & Process Calibrators
-
The most sophisticated industrial equipment will not be useful unless it is calibrated. GAOTek Process Calibrators are used to adjust instruments’ accuracy, and they are the only process calibrator you will ever need to carry. They can measure temperature, pressure, voltage, resistance and frequency, and can be used during troubleshooting. Through calibration, you can ensure that any equipment performs as expected and that it can be relied on to deliver predictable and accurate results that meet quality standards. GAOTek Process Calibrators come with a USB interface which makes it easier to transfer the results to other devices which otherwise would have taken a long time to transcribe them. Our Process Calibrators are for sale to the United States, Canada and globally.
-
Product
Single Channel High Voltage Linear Amplifier
A600
-
The A600 is a general purpose broadband linear amplifier having a fixed amplification of 100 times and capable of bipolar high voltage output of 300V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to 3 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
Product
PXIe-5764, 16-Bit, 1 GS/s, 4-Channel PXI FlexRIO Digitizer
785167-01
FlexRio Digitizer
The PXIe-5764 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PXIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
Digital (1kV up) H.V. Insulation Tester
6213A IN (Ranges: 0.5kV to 10kV 0.5kV increment steps)
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● 2 ×16 characters; large intelligent LCD module.● 20 Insulation test voltages 500V, 1kV, 1.5kV, 2kV, 2.5kV, 3kV, 3.5kV, 4kV, 4.5kV, 5kV, 5.5kV, 6kV, 6.5kV, 7kV, 7.5kV, 8kV, 8.5kV, 9kV, 9.5kV, 10kV.● Ener-Save™ feature to extend battery life.● Bar-graph indicates test voltage; rise and decay can be observed.● Visual and audible warning if external voltage is present (>500Vac or Vdc.)● Insulation resistance; auto-ranging on all ranges.● Overload protection.● Low battery indicator (read time battery voltage measurement).● Measures insulation time duration of the test.● Low battery consumption.● Better than 10% accuracy on all ranges.● Auto-off.● Calculates Dielectric Absorption Ratio (DAR) automatically.● Calculates Polarization Index (PI) automatically.
-
Product
Precision Time Protocol
IEEE-1588
-
Meinberg Funkuhren GmbH & Co. KG
As a high-stability Grandmaster Clock in IEEE 1588-2008 networks, the MEINBERG NTP time servers with highly accurate PTP clients ("slaves", such as the PTP270PEX or PTP SYNCBOX ) At the same time as the current absolute time.
