Showing results: 1141 - 1155 of 5411 items found.
-
HCF-F1000L -
MCH Instruments Co.,Ltd.
FEATURE:*Period,totalize measurement self test*High sensitioity:85dBV (25mVrms)*Stability:±3x10-9/s*8 digit LED display*Gate Time:0.01s,0.1s,1s*Power supply:AC 220V(110V optional)
-
IFTOOLS GmbH
for analysis and optimizing of all RS232 and RS422/485 field-bus connections. It gathers exact information about every line change with 1µsec precision – indispensable for each analysis of time depending protocols like Modbus RTU, Profibus or similiar.
-
TY400C -
TESTEX Testing Equipment Systems Ltd.
Automatic Single Yarn Strength Tester, to determine the breaking strength and elongation rate of single yarns made of cotton, wool and others up to 6000cN, with air-driven clamps. Fully automatic, can test 20 cops at the same time.
-
Absolute Futurity
BBMonitor will display a graph over time of your connection behavior. It will also show you real-time displays for upload and download speeds. You can check averages, peaks, and low points. Bandwidth speed testing can be no easier than this.
-
National Technical Systems
Whenever products and materials spend extended periods of time in a humid environment, various types of breakdowns can be expected. Coatings can fail. Electronic and optical equipment tends to degrade. Fuels break down. The list of associated failures is extensive.
-
The Dickson Company
Data loggers are electronic devices which automatically monitor and record environmental parameters over time, allowing conditions to be measured, documented, analysed and validated. The data logger contains a sensor to receive the information and a computer chip to store it.
-
Froment Sigma Dynamometers
Froment Sigma Dynamometers test, prove and exercise agricultural tractors and self-propelled machinery with maximum efficiency and with the minimum waste of time and fuel. Testing is quick, accurate and simple to carry out, with a choice of automatic or manual test modes.
-
VIEW-101 -
Neulog
The Graphic display module is used to run experimentswithout a PC. It displays the sensor's measurements indigital and graphical forms. It can also be used to program thesensor's experiment setup as well as viewing the input from up tofive sensors at a time.
-
40-191B-012 -
Pickering Interfaces Ltd.
The 40-191B is a PXI fault insertion switch using solid state switching elements and is capable of carrying 40A on single channel or 30A on all channels at the same time and provides a robust solution to high current fault insertion.
-
Shenzhen Noyafa Electronic CO.,LTD
NOYAFA CCTV Moniter Tester has a built-in high-resolution and wide-size high-definition screen display, automatic video signal detection (AHD / TVI / CVI). The design of the monitor and wristband is ergonomic and convenient to use at any time and place.
-
OHT Inc.
*This system can measure MRAM characteristics automatically.*Automatically initializes(resets) before and shorten the time of measurement by having a built in initializer.*Generates strong and constant magnetic fields. (Prober: Max 1.5T, Initializer: 2.7T (the highest in the industry)
-
N9048B -
Keysight Technologies
Keysight's N9048B PXE is a standards-compliant EMI test receiver equipped with an RF pre-selector and LNA designs. Shorten your overall test time and easily perform gapless signal capture and analysis with real-time scan (RTS) capabilities.
-
N2820A -
Keysight Technologies
The N2820A 2-channel current probe connects to two oscilloscope channels to provide simultaneous low- and high-gain views for wider dynamic range measurement, while the N2821A 1-channel current probe provides one user-selectable view at a time.
-
ET Power Systems Ltd.
An adjustable electronic load gives the test engineer the ability to qualify designs, check production batches or service and repair electrical products. Many applications demand an adjustable electronic load. These include the burn-in of new devices along with general power supply, battery, fuel cell and generator testing.Both static and fully dynamic DC loads are offered. With dynamic functionality 2 levels of load current can be set. The rise and fall time can then be adjusted together with the time period spent at each level. The load can also be made to follow complex waveforms by tracking an external arbitrary oscillator input.
-
NGU -
Rohde & Schwarz GmbH & Co. KG
Thanks to their extremely high accuracy and fast load recovery time, the R&S®NGU source measure units (SMU) are perfect for challenging applications. A special ammeter design is used to precisely measure current drains from nA to A in one pass – no need to make multiple measurement sweeps. The instruments’ short recovery times enable them to handle fast load changes that occur, for example, when mobile communications devices switch from sleep mode to transmit mode. With high speed data acquisition, every detail is detected down to 2 μs resolution.