-
product
IPX9K Rain Spray Testing Chamber / Rain Resistant Test Machine
CX-IP9K
Shenzhen Chuangxin Instruments Co., Ltd.
Water Spray Test Equipment is used to test the water resistance; which is mainly for electronic and electrical products. It can also provide references for product design and quality control.
-
product
NFC and Mobile Payment Application Testing
An increasing number of banks and mobile operators are now offering mobile contactless payments to their customers. As with EMV contactless cards, the mobile payment application contained on the SIM needs to be certified by the contactless payment schemes, and in some cases by GlobalPlatform.
-
product
Polarization Controller and Scrambler - PXIe
Pol 1000 Series
The Pol 1000 Series PXIe module enables high-speed automated polarization control for polarization dependent testing procedures.Rotate or scramble the polarization of your signal with no need for manual adjustment of paddles or tension screws using intuitive software, LabVIEW or comprehensive SCPI commands. Pol 1000 Series can be used with our wide range of optical and electrical PXIe test modules, and can be used to build complete mixed-signal test platforms.
-
product
Bipolar/FET/Diode Dual Head Production Test System
36XX
Two test stations on the 3600E and 3601E systems. Performs DC, AC, and pulsed tests. Excels at evaluating difficult to measure parameters on zeners, current limiters, varactor tuning diodes and darlingtons. 24 bin opto-isolated handler/prober interface. Parallel first-in first out computer to tester interface for maximum throughput. Parallel testing with a 3602E or 3603E allows shared test execution for extremely high throughput applications when interfaced to high speed handlers with multiple test sites.
-
product
Programmable DC Electronic Load
IT8500+ Series
IT8500+series (150W~3000W) single-channel programmable DC electronic loads are designed for middle & high-end applications. They can be offered as multiple solutions according to customer's design and testing requirements.
-
product
Antenna, High Field Biconical
EM-6913 | 20 MHz – 300 MHz
The Electro-Metrics EM-6913 can be used for generating high intensity fields as required for EMC immunity testing 20 MHz to 300 MHz.
-
product
Support Equipment & Systems
The Atec Companies specialize in the engine specific ground support equipment and ancillary support systems utilized in all types of turbine engine testing.
-
product
Battery Test Chambers
At Weiss Technik we supply battery test chambers specific to testing batteries in a variety of conditions including low or high temperatures, humidity changes, vibration changes, and altitude changes. Our battery test chambers are designed to test Lithium Ion batteries, lead acid, Battery Managements Systems (BMS), battery packs, modules, battery cells, and more.
-
product
EMC/EMI Testing
NCEE Labs has state of the art test equipment and experienced iNARTE EMC/EMI and qualified staff to provide Electromagnetic Compatibility (EMC) and Electromagnetic Interference (EMI) testing. The lab maintains accreditation to the latest FCC, CE and other international EMC/EMI standards.
-
product
PXI Strain Gauge Simulator Module 6-Channel, 1.5k
40-265-406
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 1.5kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
4 2/3 Digital Temperature (RTD) Meter
CS2-T
Chuan Sheng Electronics Co., Ltd.
CS2-T Temperature Indicator has been designed with high accuracy measurement, display and communication of Thermocouple or Pt100Ω.They are also building in 4 Relay outputs, 3 External Control Inputs, 1 Analogue output and 1 RS485 (Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of machinery and testing equipments application.
-
product
Portable Meter Test Kit
UTEC 430
The UTEC 430 is the first Portable Meter Test Kit to support both the Radian Dytronic (RD) and the installed base of Radian Metronic (RM) reference standards. The ability to support both reference standards makes the 430 the ideal budgetary solution for traditional on-site meter testing using Phantom Load current sourcing. Do not let its compactness fool you, the UTEC 430 has three 30 Amp current output elements for performing single-phase or three-phase meter testing. When each element is combined using the optional open link cable harness, the UTEC 430 can source up to 90 Amps.
-
product
Automotive Transient Surge Simulator Model
ISS-7600 Series
Designed to meet and exceed the testing needs to ISO7637-2 (2004), NoiseKen ISS-7600 series Automotive Transient Surge Simulator System offers flexible and productive testing facilities.
-
product
PXI Precision Resistor Module 4-Channel, 2 to 102k
40-297-134
This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Wound Component EST Analyzer
19036
Chroma Systems Solutions, Inc.
The industry’s first Wound Component Electrical Safety Test (EST) Analyzer that combines impulse winding, AC/DC hipot, insulation resistance and DC resistance test measurement functions. Chroma’s 19036 Wound Component EST Analyzer has 5kVac/ 6kVdc high voltage output, 5kV insulation resistance, 6kV layer short impulse voltage and 4-wire DC resistance measurement with a maximum output of up to 40 channels. Capable of outputting and measuring AC100mA/DC 20mA, Chroma’s 19036 is suitable for testing to high power motor standards such as UL 1004-1.
-
product
ASA200
The ASA200 Analog Signature Analyser will assist you in testing, diagnosing and troubleshooting printed circuit boards without powering them (known as ‘power-off testing’).Connected via USB to a compatible PC running our own free software the ASA200 you can easily capture, measure and compare known good signatures (from your ‘golden’ board) with signatures from your suspect board. The built-in gate/bias generator (+/-10V, 100ohm source impedance) can be used to help test active components such a...show more -
product
Battery Testing
With the increasing dependency of back up systems on battery strings, and the escalating cost of replacing batteries, instrumentation and software systems that can measure, trend and manage the life-cycle of cells is a cost effective option.
-
product
Bally Waterproofness Tester
UI-FT20
Bally Waterproofness Tester is to test materials like coated leather, leather dynamic water penetration resistance ability. The material would be partially put in water and the bally water penetration tester would flex the sample in the water under certain speed to simulate material water resistance in daily work. Here for more Leather Testing Machine.
-
product
Electrical Safety Analyzers
Fluke Biomedical electrical safety analyzers provide accurate and reliable results, helping you meet your medical device testing and quality requirements while ensuring patient safety.
-
product
Battery Testing Equipment
With the increasing dependency of back up systems on battery strings, and the escalating cost of replacing batteries, instrumentation and software systems that can measure, trend and manage the life-cycle of cells is a cost effective option.
-
product
Thermal Tools
BMP Testing and Calibration Services Inc.
BMP Testing and Calibration Services, Inc. utilizes the latest thermal measurement equipment to analyze low to medium-conductivity materials, from ceramics, plastics, and polymers to coatings, composites, liquids, and building materials.
-
product
Test Case Management System
Kiwi TCMS
The leading open source test case management system. *Efficiently manage test cases, plans and runs*Improve testing productivity & reporting*Integrates with popular issue trackers*External API interface*GPL 2 licensed
-
product
USB-7846, Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
783201-01
Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The USB‑7846 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7...show more -
product
Flightline Pilot Static Test Set
ADTS-3350 Series
TestVonics™ ADTS-3350 Series Test Set is a portable, high precision, dual channel pitot static test system. This tester is designed to calibrate, test and troubleshoot air data instrumentation and aircraft pitot-static systems. The test set has been designed with functional and reliability features highly suited to withstand the harsh environmental and demanding conditions of the flight line environment, especially for military end users. The test set is designed for testing a wide range of comm...show more -
product
Antenna Kits
Com-Power offers five portable antenna kits suitable for offsite EMC testing. These kits are supplied with a custom hard plastic carrying case which has individual compartments for all the included items.
-
product
Ground Testing
Weshine Electric Manufacturing Co., Ltd
1.Soil resistivity tester supports 2, 3 and 4wire grounding resistance measurement. 2. 4digit large LCD display with white screen backlight, suitable for use in dimly lit places. 3. IP65 protection grade, good waterproof, compact and portable, supports multiple functional tests.
-
product
Single Position Meter Test Station
LS3
Calmet Smart Calibration Devices
Stationary three phase system class 0.01% for automatic testing of single electricity meter. It allows to test all type of meters
-
product
Date & Time Simulation Software
TimeShiftX
TimeShiftX is a date and time simulation software that lets you time travel software into the future or past for temporal testing all date and time sensitive functionality and code such as end of year/month, daylight savings, leap year, billing, rates, policies, etc. Perform time travel testing instantly, without any code changes, manual work, or server isolation
-
product
150 kHz-230 MHz Broadband Power Amplifiers
Output power up to 80W for standard conducted immunity testing. Our 150 kHz-230 MHz amplifier range covers output power ranging from 20 W to 80 W.
-
product
SMART Constant Current DC Load Banks
SLB-Series
SMART Constant Current DC Load Banks are designed for acceptance testing, discharge testing, battery capacity testing, battery maintenance, engineering examination and other testing for DC power with load. The SMART technology allows a constant current discharge without the need for manual adjustment of current during the discharge test. Our SLB-Series load banks are portable, durable, economic, safe, easy-to-use and come complete with our DataView software, providing the user with a complete data management and analysis program.
