Showing results: 2026 - 2040 of 5276 items found.
-
KT-95 -
KILTER ELECTRONIC CO.,LTD
Test device with UTP (Unshielded Twisted pair) ,STP (Shielded Twist Pair) and coaxial wiring ; Test with BNC and RJ45 socket. Test cable length, Check wire continuity, open, short, reversal and miswire. Main unit and one remote allow one person operate. Length Test Range:20m/200m/2km/20km Accuracy: À1% rdg À 0.3m. Self Calibrate available
-
Beha-Amprobe
Built tough for use in industrial and commercial environments, measures voltage range up to 1000 V AC and 1200 V DC (2100-Gamma only). Designed with reinforced components for dependable performance.
-
PeakTech Prüf- und Messtechnik GmbH
Direction indicators are indispensable for use in the electrical assembly of three-phase motors. In normal use, the test leads are connected to the live terminals, with an R / L display showing the later direction of rotation of the electric motor. In addition, this model can be used for the contactless determination of the direction of rotation of switched-off or not connected motors. Place the switched-on measuring device on the motor parallel to the longitudinal axis without test leads. Now turn the shaft of the motor, the measuring device now shows a right or left movement.
-
Vibratron II -
Physitemp Instruments
The Vibratron II provides a non-invasive means of measuring the sensitivity to vibration of large nerve fibers of a patient's fingers and toes. Reliable quantitative measurements are achieved with a test that takes only minutes to administer. A two-alternative forced choice procedure is used to determine the degree of sensitivity for comparison to normals.
-
DZ800 -
Shanghai Aoboor Electric Co., Ltd.
Insulation resistance, HIPOT, coil DC resistance, turn to turn surge tests can be automatically completed in one time. Applicable to electrical performance test of solenoid valves, changeover valves
-
SPS electronic GmbH
The impulse voltage test devices from SPS electronic are ideal for detecting interturn faults and insulation faults within a winding - even before the fault affects the electrical specifications of the test object.
-
Statclean Technology (S) Pte Ltd
ESD wrist strap is most commonly used protective devices which prevent the build-up of electrostatic charge on personnel. The random failure of wrist strap compromises the protection. Thus, it is important to test every wrist strap regularly.
-
TEK500 -
Martindale Electric Co. Ltd
An easy to use, low cost pass / fail microwave leakage detector suitable for commercial and domestic microwave ovens. It is designed to comply with national standards on permitted exposure levels. The TEK500 includes a self test which simulates a real microwave input to ensure the unit is working correctly at all times.
-
PTE-50-CET -
EUROSMC, S.A.
The equipment comprises of three independent output channels that can be selected as current or voltage. This enables the unit to be used as a complete single-phase equipment (voltage, current, and phase angle between them) or, with channels synchronised, as a three phase current or three phase voltage generator from a single phase mains input.
-
LinkRunner® G2 -
NetAlly, LLC
Validate up to 90W Power over Ethernet (PoE) PSE in one AutoTest – useful during IoT, VoIP, and Wi-Fi deployment. Install and run preferred Android-based apps for speed tests, device configuration, and workflow management with smartphone-like features.
-
Testboy GmbH
Using the new Testavit Schuki 1 LCD and 3 LCD, specialists easily check to see if sockets, cable drums or connecting cables are correctly connected in 230 V installations. Due to three LEDs, the connection status can be quickly and clearly determined. In addition, through the finger contact, it can be tested to see whether an impermissible, high contact voltage is applied at the protective earth connection. In addition, using the Testavit Schuki 1 LCD, a 30 mA FI circuit breaker (RCD) can be triggered via a pushbutton.
-
Maschinenbau Haldenwang GmbH & Co. KG.
Display on LON analog displays with theEvaluation in "Lehr''s damping factor" or damping ratio "D"Fully automatic testAutomatic test start after bilateral plate load of more than 60kgFrequency controlled drive excitation by electric motors to determine the maximum vibration amplitude with subsequent evaluation of the axle dampingrunning underbody as self-supporting frame constructionParallelogram guided test plates, thus no fixed wheel contact requiredgalvanized version
-
SLT 1 -
Maschinenbau Haldenwang GmbH & Co. KG.
Mobile handheld device with illuminated display and keypad for K-value determination and speed limiter function testConnector for multi-function plug (incl.)Adapter cable for VDO Kienzle tachograph TCO 1314Adapter cable for VDO Kienzle tachograph KTCO 1318, TVI 8400Adapter cable for VDO Kienzle tachograph FTCO 1319 TVI 2400Adapter cable for VDO Kienzle Tachograph MTCO 1324Adapter cable for Motometer tachograph EGK 100Earth terminal cable with clampPower supply 230 V / 50 Hz with 12 V DC charging voltageBoard power adapter 12/24 V DC 12 V DC charging voltagePlastic case
-
KT-97B -
KILTER ELECTRONIC CO.,LTD
3 1/2 digits, Max. reading 1999Test battery Impedance, resolution up to 0.01mΩTest Voltage onlineFit to test battery: lead-acid, Li-ion; Ni-HM, etcTest the battery used in UPS,automotive,mobile phone,etcPure AC 1,000Hz test mode4 wire test clip with high accuracy
-
PAT-2E -
Sonel S.A.
The innovative combination of small dimensions (full portability of the device) with advanced measuring systems allow to carry out fully automated measurements for electrical equipment, IEC cables and extension cords (including those with PRCD). The set of tests is performed with one click of START button. Confi guration options of the meter allow you to modify the operation of the device, and thus, tailor it to the needs of the user. In situations, where it is necessary to perform simple and single measurement, without the need to do complex measurement procedure, Pat Sonel allow you to work in a single measurement mode of a given type (ie. Manual). All meters in this series (PAT) also allow you to make basic measurements without external power in emergency situations i.e. in the absence of the power one can easily run a simplifi ed set of test in a battery mode. Small size, weight, and specially designed carrying case of the meter and accessories provide comfort and high mobility. Wireless communication with a printer enables organization of the working site without the hassle of unnecessary cables. Storage and integration of the results in PC software further extends the functionality of the instrument.