-
product
Dynamometer Power Supply
DES Series
The DES 310 and DES 311 power supplies are suited to the entire range of Magtrol's Eddy-Current and Powder Brake Dynamometers. To avoid any disruption of the surrounding electronic modules, the DES 310 / DES 311 supplies are fitted in an industrial housing made of extruded cast aluminum. This housing must be installed directly on the test bench, as near to the dynamometer as possible.
-
product
NEXYGENPlus PET Testing Software
AMETEK Sensors, Test & Calibration
The NEXYGENPlus PET testing software can control the barrel temperature, display test graphs and automatically calculate the required test results, e.g. IV, degradation factor and MV. User specified pass/fail limits can be set for the IV, degradation factor and/or MV and the software will indicate which samples have passed or failed. When several tests have been performed, the batch statistics can be viewed either as a data table, an X-bar range chart or a histogram.
-
product
RF Noise Source
NS-3
The NS-3 Broadband RF Noise Generator provides an extremely flat AWGN (Additive White Gaussian Noise) signal from 5 to 2150 MHz. The output level adjusts in 0.1 dB steps over a 30 dB range.The bench-top configuration is standard and an optional two unit rack enclosure is available. The RS232 or USB remote control interface simplifies its use in automated test and factory ATE environments. The NS-3's combination of range, versatility and value make it the ideal general purpose broad-spectrum signal source for bench and ATE applications, including C/N, BER, MER, PER testing and rain fade simulation.
-
product
Broadband DSL Test Set
Copper Pro 990DSL
The 990 CopperPro Series II provides a full range of troubleshooting, fault locating, testing and qualification capabilities. That means top performance with fewer tools to carry.
-
product
Data Block Mating Table
VG Series
*Aircraft, Consumer Electronics, Networking, Telecommunications and Test Systems*Custom Blocks can be designed for your specific applications please contact your local sales person to find out more
-
product
80W Power Supply, 35V, 2.2A or 60V, 1.3A
E3645A
Keysight basic DC power supplies offer essential features for a tight budget. The single & dual output, 30-100 W GPIB E3640 series provide small, compact size for bench and system use; low output ripple and noise; and built-in measurements and basic programmable features. The Keysight 78W, single output E3645A is a stable and reliable power supply for benchtop and basic automated test applications, and enables versatile solutions for tests that require moderate speed and precision with both GPIB and RS232.
-
product
Adjustable Press Plate Bed of Nails Testers
Protector Adjustable Family
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. ...show more -
product
Determines Presence of Carbonation on Concrete Samples
Carbo Detect System™
Carbo Detect is a simple colored dye field test for detecting carbonation. The single reagent is sprayed on the surface to be checked. The reagent will change to pink in uncarbonated concrete and remain colorless when sprayed on carbonated concrete.
-
product
Streamline USB Vector Network Analyzer, 32 GHz
P5006A
Compact, faceless, USB vector network analyzer (VNA). Flexible two port VNA which dramatically reduces your size of test. Up to 32 GHz.
-
product
Tensile Test Methods For Plastics: ASTM D638
Resin materials (plastics) are found in a wide variety of items used on a daily basis. Recently, plastics have started to be used as structural materials in transportation equipment, such as automobiles and aircraft, due to their strength and light-weight nature. In these applications, it is important to understand the mechanical strength properties of these plastics. ASTM D638 specifies methods for testing the tensile strength of plastics and other resin materials and for calculating their mechanical properties, and outlines accuracy requirements for the test frames and accessories used.
-
product
Harmonic Filter Resistors
Post Glover designs, builds and tests their harmonic filter resistors in accordance with applicable IEC and IEEE standards to guarantee their performance. With no two installations ever being the same, our experienced engineers develop the proper solution for your particular application and environment. Our low inductance designs are built using all stainless steel elements in corrosion resistant enclosures chosen for your unique specification. Request a quote for your custom harmonic filter resistor.
-
product
Terahertz Spectroscopy Solutions
STRIPP Control IM
Teratonics offers innovative solutions for contactless non-destructive testing and imaging inside dielectric materials and on coated metallic surfaces. Based on the patented technology and our profound know how on its application, we offer: ► Instruments for product and process control as well as for inspection with automated evaluation ► Laboratory services for industrial R&D, fatigue tests, maintenance, end of life studies
-
product
USB Type-C Interconnects Compliance Test Software
S94USBCB
Use the S94USBCB software to test, debug and characterize your USB Type-C cable and connector designs. The PathWave TAP based test sequencer automates the network analyzer (VNA) for each test and generates a comprehensive HTML report. When run with L8990M switch matrix, it enables 20-ports fully automated test without port re-connection.
-
product
300mm Single Touchdown Burn-in and Test System
FOX-15
Up to 15 wafers at a time Known Good Die solution Lowers production cost
-
product
Production PCB Combinational Tester
The PT100Pro combines ARM Functional Test, Analog Test and Boundary Scan in one platform for testing up to 32 PCBs at a time. The PT100 Pro solves the test challenges and cost requirements of testing small, high-volume PCBs used in the home, mobile, entertainment, automotive and embedded markets. PCBs in these markets are cost sensitive yet require high volume, high fault coverage on leading edge technologies such as WiFi, DDR Memory, USB, Bluetooth, Nand Flash, MPEG decoders, Power Management Units, and MMC/Smart Cards interfaces.
-
product
Generates Test Cases on ICE
TrekSoC-Si
TrekSoC-Si automatically generates self-verifying C test cases to run on the embedded processors in SoCs in in-circuit emulation (ICE), FPGA prototyping, and production silicon. This verifies your chips more quickly and more thoroughly than hand-written diagnostics or running only production code on the processors. TrekSoC-Si's generated test cases target all aspects of full-SoC verification and work in a variety of different environments. TrekSoC-Si is a companion to TrekSoC, which generates test cases for simulation and acceleration. TrekSoC-Si extends the benefits of TrekSoC into hardware platforms.
-
product
1149.6 Boundary Scan Feature, GTE 10.00p
K8213A
Keysight’s Interconnect Plus Boundary Scan 1149.6 feature enables all the tools required to develop and execute this test method on the board under test. Compared to the 1149.1 standards, the 1149.6 standards define test methods for the boundary scan devices that are designed with AC coupled signals or differential nets needed for high-speed operations of the device.
-
product
Turns Ratio and Phase Tester
SS310
Turn ratio meter is a reliable test instrument used for product inspection and sample analysis in the manufacture of transformer, radio and TV set or relative scientific research units.
-
product
Automatic Voltage Regulating Relay- Standard Model
NMC’s Microcontroller based Automatic Voltage Regulating Relays (AVR Relays) are latest technology based Relays used for regulating the secondary voltage of Power Transformers with On Load Tap Changer (OLTC). The Parameter settings are made through the front panel keys & are stored in NVRAM. Independent time delays can be set for first control pulse & subsequent pulses. Built-in Tap displays Tap number of Power Transformer. OLTC is blocked for UV, OV, OC, CF, Min/Max Tap Positions & ...show more -
product
Vertical Shock/Bump Tester (Pneumatic)
HIACC Engineering & Services Pvt. Ltd.
The pneumatic vertical shock and bump test system features an advanced design with a high degree of performance and automation. The testes is easy to use and have low maintenance requirements.
-
product
Filter Testers
All filter test equipment from TSI, used for testing efficiencies of filter media and a variety of air filters, including high and very high-efficiency filters, respiratory filters, cartridges, and protective garments, is known for its simple and reliable operation. All of our filter testers can determine the efficiency of filters using submicron poly- and monodisperse oil and/or sodium chloride aerosol. Additionally, TSI's filter test solutions are used to comply with various testing standards and regulations around the globe.
-
product
Digital (1kV below) Insulation Tester
1851 IN
Standard Electric Works Co., Ltd
● Measures insulation (MΩ), Continuity (Ω) and AC voltage.● Three insulation test voltages(DC V) : 250V, 500V, 1000V.● 3½ digital LCD (2000 counts).● 68 × 34mm (2.677” × 1.338” ) large LCD display.● Automatic circuit discharge.● Test insulation at rated voltage into a 1mA load.● 210mA short circuit testing current for continuity.● External voltage warning indication.● Fuse protection.● BS 16 edition
-
product
Torque Measuring and Monitoring System
WISER 4000
TECAT Performance Systems, LLC
The WISER 4000 system is the latest release of TECAT’s low-cost, ultra-low power and extremely accurate torque sensor. The wireless system has the optional ability to measure 3-axis acceleration, barometric pressure and ambient temperature, all within the same incredibly small footprint. The 4000 includes on-board data logging without PC or DAQ connectivity, and remote flash capability, which enables firmware upgrades without removing the system from the unit under test. Featuring shunt calibrat...show more -
product
Reach-In Conditioning Test Chamber
Weiber Conditioning Test Chamber Manufacturers offers an ideal apparatus for conditioning materials at non-ambient temperatures. Now researchers, engineers, and technicians have a simple and cost effective method to condition samples prior to testing. Laboratory Conditioning Chamber is designed for the conditioning of samples prior to testing, provides conditions from 20% to 98% RH ± 2 and 0°C to 94°C ± 0.5°C.Conditioning Test Chambers offers ideal humidity and temperature conditions required fo...show more -
product
Temperature Rise Tester
WS-1
Applied to test electrical accessories heating conditions when connected to load current, whether the temperature rise of electrode is compliance with standard requirement or not. And it can effectively detect whether the plug bush is slants thin and whether plug and socket cooperated with all right. It is designed and manufactured according to IEC884-1, GB2099.1-2008 and other relevant standard of electrical accessories.
-
product
Compact Manual Ranging 600V Multimeter
DL9204
Compact manual ranging digital multimeter with 2000 count LCD display. Full protection on all ranges, safety category to CAT 111 600 V. Functions include battery and diode test.
-
product
3 Wire (Digital) Earth Resistance Tester
ST-1520
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● Auto power off function.● The timer operates automatically for about three to five minutes when the "PUSH BUTTON SWITCH" and "TIMER ON BUTTON" are pressed together. This will keep test "ON" for the duration of the timer.● Timer for test function (count 3-5 minutes).● Battery operated.● Data hold function.● Small and light weight.● Calibration performed with supplied test leads.
-
product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 255 Ohm - SPST
50-294-113
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI 10W Programmable Resistor Module, 1-Channel, 2Ω to 52.4kΩ
40-253-033
The 40-253-033 is a programmable resistor module with 1 channel which can be set between 2Ω and 54.4kΩ with 1Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.