-
product
Caraya Unit Tester
Caraya is a new experimental open source assertion and unit testing framework for LabVIEW. It takes a whole new approach to unit testing; your VI is your test. Caraya allows you to convert your manual test VIs you use for debugging into unit test cases with nearly no effort. Even running the tests is easy, just run the test case VI. Caraya significantly lowers the barrier for developers to write unit tests leading into improved overall code quality in real-world projects where developers don’t always have the luxury to write unit test cases first.
-
product
Time Domain Reflectometer (TDR) Card
PCI-3127
The PCI-3127 is a PCMCIA-form factor TDR that can be used to identify and locate failures in installed wiring and cable systems. The instrument can make high resolution TDR measurements on circuits up to 96,000 feet (~30km) from your Windows XP notebook computer or PC using a low-voltage non-destructive test signal.
-
product
Emergency Conditions Testing
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
product
EBIRST 100-pin SCSI Termination Fixture
93-019-104
93-019-104 eBIRST Termination Fixture is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
DDR5 Logic Analyzer
FS2601
The FS2601 is one of our newest and fastest logic analyzer probes used to test DDR5 memory. It is designed to work exclusively with 4 Keysight U4164A logic analysis modules operating in either Quad Sample State or Quarter Channel 10GHz timing modes. This gives the user an extremely effective tool for debugging, testing and verifying DDR5 UDIMMs running above 4000MT/s.
-
product
Enerchron® 2.0 Test Management Software
Enerchron 2.0 test management software is a software suite ideally suited for test applications that yield extensive data over an extended period of time such as battery cycling and evaluation. It allows the creation of complex, dynamic test sequences without requiring the skills of a programmer. In addition to real-time viewing during execution, measurements are automatically archived for review and analysis after testing has been completed. Enerchron is available with NH Research’s Regenerativ...show more -
product
Water-cooled Light & Weather Fastness Tester
TESTEX Testing Equipment Systems Ltd.
Xenon Lamp Weather Resistance Test Chamber, to determine the color fastness, aging resistance of textiles, plastics, rubber products or materials by objecting to the simulated conditions of nature weather (daylight, rain, temperature and humidity, etc.). Water-cooled Light Fastness Tester complies with ISO105 – B02 / B04 / 06, AATCC 16, AATCC 169, etc.
-
product
Automotive Paint Thickness Meters
Shenzhen Linshang Technology Co., Ltd.
Linshang automotive paint meter, also named paint thickness meter, is a painting thickness gauge used to test car paint thickness. Linshang automotive paint meter can identify the substrate automatically. If you devote to find a cost effective paint thickness meter, you can view the digital coating thickness gauges listed below.
-
product
ACCUplace BullsEye /Recognition Grid
AP-B Series
A unique concept in imaging calibration technology, The ACCUplace Bulls Eye / Recognition Grid allows the end user to calibrate magnification at multiple power levels, as well as test the system’s ability to recognize and locate distinctive shapes within shapes by focusing on the concentric circles.Each Bulls Eye / Recognition Grid target has individual patterns consisting of 5 concentric circles with 0.50mm line width and 0.50mm spacing between circles (10mm Pitch) with a 0.100mm center dot. In addition, each row and column is labeled with X & Y coordinates. The AP-B series is offered on four standard substrates; Chrome on Glass (CG) Opal (OP) Photopaper (RM) and Film (TM).
-
product
Bus Analyzer
FireSpy® 3430b(T)/3830(bT)
The FireSpy3430bT and FireSpy3830bT as well as FireSpy3430b and FireSpy3830 bus analyzers are DapTechnology's latest 3-bus IEEE-1394 protocol analyzer. Based on the 4th generation FireSpy analyzer architecture the FireSpy3430b(T)/3830(bT) is the most advanced 1394 test equipment in the market.
-
product
Solar Radiation (Sunshine) Test
This test determines the effects of direct solar radiation on components and material. The heating effects of solar radiation differ from those of high air temperature in that the amount of heat absorbed depends on the roughness and color of the surface on which the radiation is incident and the angle of incidence to the sun. Variations in the intensity of solar radiation over the surface of the component, may cause components to expand or contract at different rates, which can lead to severe st...show more -
product
High-Speed Embedded Host Electrical Test Board
HSEHET
High-Speed Embedded Host Electrical Test Board is approved by USB-IF, specifically designed for the electrical test of USB embedded host products.
-
product
Control Cabinet (Automatic)
HTGY / 597
Wuhan Huatian Electric Power Automation Co., Ltd.
The special supporting equipment of test transformer can seamlessly connect various test transformers of different grades.
-
product
Insulation Resistance Testers
Shanghai Beha Electronics Co., Ltd.
*This is a variable high voltage insulation tester from 500V to 15kV in 500V steps.*The is menu driven and uses Dynamic Current Auto ranging technology.*It has a Bar-Graph which displays the voltage stressing the insulation while the test is in progress and the voltage decay during the automatic discharge of the tested circuit.*The top line of the display shows the elapsed time at the start of the test. Digital readout of the total time will remain displayed even after testing has ceased.*A 4-digit display (2000 counts) is showing the actual insulation resistance.*This instrument displays a voltage warning and sounds when AC or DC is present before injecting the test voltage.
-
product
Voice/Audio Quality Analyzer
OPERA™
The OPERA™ Voice/Audio Quality Analyzer represents the latest developments to objectively evaluate and assure the quality of compressed voice and wide-band audio signals, based on modeling the human ear. With OPERA you can achieve a comprehensive analysis of the end-to-end quality of today's and next generation networks, such as VoIP, VoDSL, VoATM, ISDN, GSM, POTS, from the caller to the callee. Also, you can test the audio quality of compression formats such as MP3, AAC, AC3, Microsoft Windows Media, from the studio source to the receiver, or from the server to the client.
-
product
Multiprotocol P104Plus Interface Board for Embedded Applications or Avionics Test & Simulation Applications
EXC-4000P104plus
The EXC-4000P104plus is a multiprotocol P104plus interface board for embedded applications or avionics test and simulation applications. Each board holds up to five independent modules. Two on-board modules use the MIL-STD-1553 communications protocol (M4K1553Px); another on-board module uses the ARINC-429 communications protocol; two additional detachable modules can be any one of the following types:M4K1553PxS (Single Function - RT validated) This module operates as a Bus Controller, Remote ...show more -
product
JTAG External Modules (JEM) DIMM/SODIMM Socket Cluster Test
The primary function of the JTAG External Modules (JEM) for the DIMM/SODIMM Socket Cluster Test is to provide test access to off-board signals that otherwise could not be accessed by a JTAG test system and to strengthen the memory-independent JTAG testing for the assembly correctness of the almost full spectrum of the modern socket types, particularly (according to JEDEC_Std.21-C):
-
product
PXI 2.5W Programmable Resistor Module, 2-Channel, 3Ω to 5.82MΩ
40-251-052
The 40-251-052 is a programmable resistor module with 2 channels which can be set between 3Ω and 5.82MΩ with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Shock Test System
Labtone Test Equipment Co., LTD
Products are inevitably affected by impact, bump, free fall, tumbling etc. during production, transportation, loading and unloading as well as during the use of the products. All of these are transient excitation on the object, causing the object to produce mechanical characteristics of high speed, acceleration, strain rate instantly. These kind of characteristics are completely different from that in static load, and may cause problems to the object in terms of structural strength and stability...show more -
-
product
Turn-Key Functional / Mechanical Fixture
In addition to In-circuit testing, functional testing is widely used in the industry to verify electronic cards. This is why ReMaTek has always paid a special attention to the specific requirements of functional testing. Our dedicated engineering staff is prepared to handle all of your mechanical, electrical and software requirements. We are aiming particularly the small turn-key test systems where all the elements; the mechanical fixture, the test equipment and the test software, are put together in a complete system.
-
product
LED Test Instruments
Photobiological Safety of Lamps and Lamp System and IEC TR62471-2(2009) Guidance on Manufacturing Requirements Relating to Non-laser Optical Radiation Safety have be published addressing hazard to human (mostly eye and skin), and are completely suitable to assess the optical radiation safety of non-laser sources, such as LED products, UV radiation in general lighting products and etc.
-
product
Regular Battery Tester Models
The following are regular battery tester models for single-cell tests (coin cell/half cell/pouch cell/cylindrical cell, CT2001 & CT3001 Models) and supercapacitor test.
-
product
VB-8034, 4-Channel, 350 MHz Bandwidth VirtualBench All-in-One Instrument
784343-05
4-Channel, 350 MHz Bandwidth VirtualBench All-in-One Instrument—The VB‑8034 combines a four‑channel, 350 MHz mixed-signal oscilloscope with protocol analysis, an arbitrary waveform generator, a digital multimeter, a programmable DC power supply, and digital I/O into a single device that integrates with your PC or iPad. The VirtualBench all‑in‑one instrument is simple and convenient and results in more efficient circuit design, debugging, and validation. The included software provides an interact...show more -
product
PXI 8-slot BRIC Multiplexer, 6-Channel, 160-Pole (8 Sub-cards)
40-570A-016
The 40-570A-016 is a 6-channel, 160-pole High-Density Multiplexer and is part of our BRIC family. The 40-570A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.>
-
product
Adjustable Multisite Rail System™
The Celadon Rail System allows multi-site testing capability with flexible die to die spacing using existing Celadon VersaTiles™ to minimize cost of test with new DUT structures. The modular design allows for additional site assemblies and rail assemblies to be added after the original system purchase. With the Celadon Light-Tight Enclosure and Rail System Tool, high accuracy alignment and testing can be performed at extreme temperatures without affecting the thermal equilibrium of the system.
-
product
PXI 3A Power MUX BRIC, 4-Channel, 48-Pole
40-571-004
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
IEC60065 Socket Torque Balance Tester Torsion Tester
Shenzhen Chuangxin Instruments Co., Ltd.
*Plug and Socket Torque Tester/Device is for compliance is checked by engaging the device, as during intended use, with the socket-outlet of a test apparatus. *Plug Torque Tester/Equipment is a device provided with pins intended to be introduced into fixed socket-outlets shall not impose undue strain on these socket-outlets.The balancing arm of the test apparatus pivots about a horizontal axis through the centre lines of the contact tubes of the socket-outlet at a distance of 8 mm behind the eng...show more -
product
AOI Handlings System
The AOI handling system is a compact facility with various test units. Via an ionization cleaning station the ceramics are transferred to the contacting station. There, the resistance values of the substrates are tested with a rigid needle adapter. Afterward, the ceramics are further conveyed to the three (optionally four) AOI test stations (for automatic optical inspection) and are tested for cracks, unevenness, faulty imprints, contamination, etc. The poorly evaluated ceramics arrive at a revi...show more -
product
Flexible Functional Tester
igentic® 421t
Electronics customers require greater test flexibility to address the growing trend towards high-mix, low-volume printed circuit board (PCB) production. Sterner Automation is pleased to introduce the igentic® 421t, the next generation of automated test solution specially engineered to address these challenges. The igentic® 421t provides the flexibility, reliability and efficiency needed in one standard platform, allowing our customers to test multiple PCB's and significantly reduce individual product testing costs.
