Test Systems
group of interoperable devices whose integration perform a common test purpose.
See Also: Systems, Equipment, System Integrators, System Test, System Integration
-
product
PCIe 6.0 Protocol Analyzer
P5570A
Keysight PCIe 6.0 Protocol Analyzer redefines protocol debugging and validation through a new innovative CEM card form factor, bringing vast improvement in signal integrity and equalization with instant link-up to systems as well as devices under test
-
product
Memory Test System
T5511
Offering Multi-functionality and Industry's Top Test Speed of 8Gbps.
-
product
PCI Express 5.0 Protocol Exerciser/Analyzer
Summit Z58
The Summit Z58 is a PCIe 5.0 protocol traffic generation test tool used for critical test and verification intended to assist engineers in developing and improving the reliability of their systems. The Summit Z58 can emulate PCI Express 5.0 root complexes or device endpoints, allowing new designs to be tested against corner case issues.
-
product
Integrated Test Case Management System
TestLog
TestLog is an integrated test case management system. It provides a tool for software test teams and engineering companies to create and update effective test cases. TestLog has been designed with versatility in mind and should plug seamlessly into any testing methodology.
-
product
SINE M-19 Sinusoidal Array
The Sinusoidal Array SINE M-19 is a remarkable new test array that achieves 256 cycles per mm while maintaining a significant modulation. It is designed for testing high resolution optical systems such as microscopes. Because its maximum width is 7.5mm, the SINE M-19 is small enough to fit easily onto a standard microscope slide (the TM-G variation is mounted in glass).
-
product
Precison Pressure Controller Monitor
PPCM
The Precision Pressure Controller-Monitor (PPCM) is a calibration standard commonly used as a secondary standard. The PPCM provides accurate testing of air data instrumentation. The PPC-M provides a stable, repeatable and reliable standard for pressure calibration with ease of use and remote control capability through IEEE-488, located on the rear panel. . TestVonics has full calibration and repair capabilities to support all PPCM systems.
-
product
Bi-Axial or Axial Averaging Extensometers
Model 3560
Jinan Testing Equipment IE Corporation
This extensometer is ideally suited for testing anisotropic materials such as advanced composites as well as for general purpose tests like determining Poisson’s ratio. The Model 3560BIA uses a design unique to Epsilon, where the knife edges remain parallel during the displacement. This approach greatly reduces crosstalk between axes and allows use on round or flat specimens with equal ease. These extensometers are very easy to mount. Integral springs hold the unit on the test sample. The parall...show more -
product
Miniature Vibration Test System
G-2 Series
The G-2 Series Miniature Vibration Test System, though compact & handy, consists of a sweep oscillator, sine controller, power amplifier and vibration generator, thus suited to a variety of applications; calibration of sensors, standardized vibration tests for small parts, school teaching materials and modal analysis. The G-2002 is handy, with all the composed units being incorporated in a portable case.
-
product
Testing Services
Howland & Lawrence Chamber Services
RF shield testing: IEEE-299, MIL-STD-285, NSA 65-6CTIA CATL certification testing: Probe symmetry and amplitude ripple measurements following Test Plan for Wireless Device Over-the-Air PerformanceAnechoic material test, inspection, remediation: VSWR, inverse spherical nearfield testing of installed material and NRL arch screening tests of individual absorber pieces We can also provide in-process testing of welded steel shielded enclosures with a test technique based on ASME BPVC vacuum box t...show more -
product
Flying Probe PCB Test and Repair System
GRS500
Designed to help troubleshoot complex boards when fixture based tools are not a viable solution, the GRS500 is designed to help you compare the characteristics of good and faulty PCBs, using nodal impedance test, and a "Videosection" technique which presents you with high resolution images of a good board for use in live video comparison with the board under test,
-
product
PXI/PXIe MEMS RF Multiplexer, Single 4-Channel, 4GHz, 50Ω, MCX
40-878-212
The module is based on the latest micro-electromechanical system (MEMS) switching technology and has low insertion loss and VSWR. In addition, MEMS devices have a long operational life of >3 billion operations and benefit from an operating time of <20 μs allowing greater test system throughput. The multiplexers have excellent and repeatable RF characteristics beyond 4 GHz with each path having a nominally equal insertion loss.
-
product
Automotive EMC test systems
Dozens of manufacturer's and other automotive immunity standards with their roots in ISO 7637 continue to evolve bringing new challenges to users of conducted immunity testing. Teseq continues to advance the state of the art, bringing simple, flexible solutions for the challenging and fast-changing requirements that are 42 V ready.Teseq has been at the forefront of the pioneering work to establish EMC tests for motor vehicle electronics. Automotive manufacturers and suppliers worldwide have come to trust test systems from Teseq. Active involvement in the standardization committees ensures that the latest advances are continously reflected in our test systems.
-
product
Advanced 3D Automatic X-Ray Inspection
V810 S2EX
V810 is "3D Automatic X-ray inspection System" that corresponds to the double side mounting SMT-PCB that is not able to be checked by a transmission-type X-ray machine. It has the ability to detect a wide range of defects, and It have 100% complete defect detection capability in the Hip-defective.And, it is the inspection machine of world's highest level that combines the ability of the ultra-fast test speed and the lowest false call positives further.
-
product
AC Dielectric Test Systems
700-DI
The HIPOTRONICS standard line of AC Dielectric Test Systems are designed to perform high voltage AC tests on electrical apparatus in accordance with IEC60, IEEE 4 and IEC 270 and other national test standards. A variety of mechanical configurations are available to suit different installation conditions. Some models can be supplied in mobile versions when it is difficult to move the test object to the test area. AC Dielectric Test Sets are available in a wide range of voltage and power ratings with exceptional reliability, durability and functionality. No matter what your requirement is, HIPOTRONICS has an affordably priced, highly reliable test solution to meet your needs.
-
product
High Temperature Un-Cooled Extensometers (700 C)
Model 7642
Jinan Testing Equipment IE Corporation
These extensometers use a high-temperature capacitive sensor and do not require any cooling. They will operate up to the maximum temperature limit of most environmental chambers used in materials testing. The Model 7642 is ideal for testing composites, metals and high temperature polymers in tensile, compression or cyclic testing. All units can be displaced in both compression and tension. The extensometer is supplied with the advanced DT6229 controller. The standard output is 0-10VDC analog sig...show more -
product
PXI 2.5W Programmable Resistor Module, 1-Channel, 3Ω to 2.97MΩ
40-251-151
The 40-251-151 is a programmable resistor module with 1 channel which can be set between 3Ω and 2.97MΩ with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Dynamic Test Systems
H3TRB | HTGB (HTGS) | RTGB (RTGS)
Durability and reliability of wide-bandgap materials such as SiC and GaN are an important topic. The focus here is on new failure mechanisms whose effects are not visible with traditional H(3)TRB/HTGS – but which nevertheless have an influence on the real application.
-
product
Electrical
This category covers test equipment required for electrical performance tests on Industrial Lighting, Street Lighting, Automotive Lighting, Appliances, Accessories & related products. A wide range of Electrical Test Panels, Electro-mechanical endurance test systems for many products, Appliance test systems and also a range of low energy spot welding machines (one of the very few products we make which are not test equipment). Equipment are custom built to suit specific customer requirements.
-
product
Defined CRPA Test System
BroadSim Wavefront Software
Protecting your GNSS systems from jamming and spoofing is more critical now than ever before. BroadSim Wavefront was designed to enable easier and more affordable CRPA receiver testing, leveraging proven software-defined architecture.
-
product
DC Power Module, 20V, 2.5A, 50W
N6733B
This module is used in both the small, multiple output 1U high N6700 Low-Profile Modular Power System (for ATE systems) and the multiple output N6705 DC Power Analyzer (for bench testing). GPIB, LAN, USB, and LXI compliance are standard. Select from more than 20 different DC power modules, ranging in capability from basic to high precision, and in power from 20 - 300 W.
-
product
Military Communications Test
Astronics testers for military radios and wireless communications systems help you keep your most critical communications up and running smoothly. Write test program sets once and deploy them instantaneously everywhere – whether your test set is in the factory, at the depot, or in operation.
-
product
Advanced Design System (ADS) Core
W2200BP
Advanced Design System (ADS) is the flagship product from Keysight EEsof EDA, the technology and innovation leader in high-frequency, mixed-signal electronic design automation (EDA). It is the only design simulation platform that enables the co-design of IC, package and board in high-frequency and hi-speed applications. ADS seamlessly integrates system, circuit, and full 3D electromagnetic simulation with Keysight's test instrumentation to perform single pass successful electronic designs repeatedly.
-
product
PXIe Vector Network Analyzer, 300 kHz to 6.5 GHz
M9371A
Pay for only the frequency range you need with a choice of six frequency ranges up to 26.5 GHz Improve accuracy, yield and margins with the best PXI VNA speed, dynamic range, trace noise and stability Add functionality to your test system with a full 2-port VNA that fits in a single PXI slot Address your multiport applications needs by cascading multiple models Increase throughput and lower costs by adding modules in a multi-site configuration
-
product
Automated Optical Switch - MATRIQ
Add optical switching capability to your test system with Quantifi Photonics’ automated optical switches. The fast and reliable optical switch will enable automated sequential testing, saving time and streamlining your test procedures.
-
product
LCZ LCR Meter
SS1062
This (SS1061 / SS1062 / SS1063) LCZ Meters are a test system for passive components designed for the use in electronic inspection or production process for quality control. They meet any demanding requirement on production speed and precision, discrimination of qualified products from unqualified ones, as well as internal setup, storing and calling function for up to 10 instrument groups, so they are actually optimum test instruments for component incoming and production inspection. Like as: transformer, inductor, resistor, capacitor, relay, motor, generator, eletric valve, contactor, cable, wire, etc..
-
product
LM-79 Moving Detector Goniophotometer
LSG-5000
Moving Detector Goniophotometer completely meets LM-79 Clause 9.3.1 and EN13032-1 clause 6.1.1.3 goniophotometer type 4 requirements. The LSG-5000 is an automatic light distribution intensity 3D curve testing system for measuring light. The measuring distance is from 5m to 30m. It can measure all types of lighting sources, LED or HID luminaires such as indoor and outdoor luminaires, roadway luminaires, street lamps, flood lights and other kinds of luminaires.
-
product
HV Test bench
It is a deeply customizable test bench which is suitable to generate frequency and amplitude controlled voltage. This test bench could be used for life test or quality test on samples or devices. It can be configured both for sinusoidal test (STANDARD version) and both for square wave or pulse test (TechSQUARE). It includes safety systems for avoiding overload and incorrect use.
-
product
Pressure Comparator (System E)
P014
AMETEK Sensors, Test & Calibration
The P014 hydraulic jack pump (System E) is an extremely effective pressure pump designed for easy, controlled, high pressure generation. Each comparator includes a 4 connection manifold, which can be used for the reference indicator, the device under test, a fine adjust, an isolation valve, or a fluid reservoir. The adjustable reference pressure port lets you set your reference gauge at the best viewing angle.
-
product
Solenoid Test Systems
The production solenoid test systems are designed to check a high volume of parts each shift, verifying all important parameters of the solenoid.
-
product
Burn-in Systems
Incal Offers A Line Of State-Of-The-Art Burn-In Testing Hardware And Software For Retrofit And/Or Total, Customized Burn-In System Configurations.
