Systems
are interconnected groups of purpose.
See Also: Equipment, Test Systems, System Integrators, System Test
-
product
Embedded Chassis With Expansion Slots For Mini-ITX SBC
ECM300
*Designed for Mini-ITX SBC with expansion slots*One 3.5" or 2.5" HDD drive bay*2 PCIe or 1 PCIe x16 expansion slots supported*Slim design with 1 system fan*250W power supply supported*Easy and quick customization
-
product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 63.7 Ohm
40-294-011
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI 2.5W Programmable Resistor Module, 2-Channel, 2.5Ω to 201kΩ
40-251-041
The 40-251-041 is a programmable resistor module with 2 channels which can be set between 2.5Ω and 201kΩ with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI 8 Slot BRIC 132x16 1-Pole (12 sub-cards)
40-562A-121-132X16
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
High Voltage Pulse Attenuators
Barth High Voltage Pulse Attenuators are matched impedance coaxial attenuators for use primarily in pulsed 50 ohm systems, or where occasional transients would damage ordinary units. The attenuator design closely matches the impedance around each resistor, to that resistor. These attenuators feature an input impedance very close to 50 ohms, with characteristics as good or better than most microwave attenuators. These units are ideal for use in nuclear and high energy experiments. Extensive testing during manufacturing insures very high reliability for single-shot experiments. A voltage coefficient of the resistive film of less than .0001 %/V allows low voltage calibration of most systems.
-
product
RF Design
As wireless continues to be a significant growth opportunity, SILENT works with commercial and industrial manufacturers to ensure time-to-market for RF and wireless enabled products. We design, build, and test RF and wireless solutions - within budget and cost guidelines - for consumer grade products and high performance circuits and systems.
-
product
Battery Starting & Charging System Analyze
12-2415
*Shown with optional 12-2416 barcode scanner*Graphical Hand-Held Tester with Thermal Printer and USB Port*Tests 12V Flooded, AGM, Gel Cell, & EFB Batteries from 100 to 2000CCA*Graphical/Symbol Based LCD display*Tests 12/24V charging and electrical systems*Stores last 70 test series with or without power*Carrying case, printing software and USB cables included*Built-in thermal printer with thermal paper (611305)*Field-Replaceable Cables (900165)
-
product
Air Data Test Calibrator
ADTS-1555
The ADTS-1555 is a high precision Air Data Test Set that can be used as to generate and measure Pitot and Static pressures. The ADTS-1555 can be used as a benchtop or installed into a standard 19-inch rackmount. The control and measurement ranges of the system make it ideal for testing commercial and military aircraft instrumentation.
-
product
Power Supplies
CL-500B
Experience our new CL-series of power supplies. It has a 120mm Blue LED cooling fan for your gaming case & it has a 3 rail 12V output to fulfill all your system needs. 700W offer a 6+2 PCI-E ready for better graphics capabilities. Painted in black, the CL-series works great and looks great.
-
product
Digital Cabinet X-ray System
XPERT 80
Kubtec's XPERT 80 brings high quality imaging and ease of use to science and research. The XPERT 80's compact self-contained cabinet, with a high resolution x-ray source, provides the sharpest images for every application. Optional sources are also available for micro-focus and soft x-ray applications.
-
product
Rain & Spray Test Chambers
ESPEC makes rain and spray testing easier by offering a standard chamber capable of published and OEM proprietary test methods.The standardized design can be configured for the rain/spray tests you need, eliminating the guesswork in buying a chamber. The system is based on the JIS/SAE specification requirements, and can also accomplish individual automaker's tests, as well as electrical-enclosure tests.
-
product
Ultrasonic Leak Detector
VPE
The Patented Superior AccuTrak VPE represents state-of-the-art technology for pinpointing leaks is air conditioning and refrigeration systems. AccuTrak is extremely sensitive to the ultrasonic sound of a turbulent gas leak. Using a technology called "heterodyning" it translates the sound to a lower frequency which your ear can interpret. AccuTrak maintains the original sound characteristics making it possible to distinguish leaks from other competing background sounds. AccuTrak is so sensitive you can actually hear the blink of an eye, yet most background noise will not interfere with detection accuracy.
-
product
Macro Inspection
High-throughput automated macro inspectionAny wafer size, in less than one second with ~75 micron resolutionSmall footprint table-top system
-
product
20GHz Dual Channel MW Benchtop Signal Generator
LSX2092B
The LSX2092B is a 20GHz Dual Channel Microwave Signal Generator, offers industry leading performance, in an easy to use benchtop box. It features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The design offers excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
-
product
Transceiver
A device which receives an electrical digital signal, converts it into an optical signal, and transmits it into the fiber or vice versa. Optical transceiver is a standard device in optical communication system.
-
product
Supercapacitor Test
The CT3001A/C battery test systems are upgraded from CT2001A/C with higher precision and data logging rate. The tester can be used to run precision tests for coin cells, pouch cells, prismatic cells, and especially supercapacitors (ultra-capacitors). Each tester has 8 independent channel which can be programmed to run constant current charge/discharge, constant voltage charge, constant power discharge, constant resistant discharge, and direct current internal resistance (DCIR) tests.
-
product
SAM Software
PVA TePla Analytical Systems GmbH
The high performance of our systems derives not least from their interaction with our specially developed software. This enables the comprehensive and precise mapping and analysis of all SAM data software.
-
product
Digital Video/Audio/Data Optical Transceiver
OD3000A
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai OD3000A digital series optical transceiver, adopts digital video coding technique and WDM technique to satisfied user's multipath digital video, audio, data, ethernet's long distant high quality optical fiber transmission because of its full-found. Product including single fiber one way digital video, single fiber 64 routes video, 128 routes audio and data uni-direction and bi-direction complication. OD3000A can transmit the camera audio/video signal, camera and tripod head control data a...show more -
product
Touch Screen Controller
EZT-570i
The EZT-570i Touch Screen Controller offers a 7" (18mm) or optional 10" (25 mm) touch screen and the latest in test chamber programming for ease of use . The controller comes standard with data logging, data file access via memory stick or PC, Ethernet control and monitoring, alarm notification via email or phone text message, data file backup, full system security, online help & voice assistance in multiple languages and more.
-
product
Machine Vision System
CVX Series
he CVX Series is loaded with powerful features that support GLOBAL STANDARDS in machine vision inspection. State-of-the-art algorithms, that can be set by any user, ensure quick setup and long-term reliability. The best solution can be selected from a variety of options. No experience required to select lighing! - newly-developed, revolutionary Lumitrax function. 3D measurement. Ultra high-resolution 21 megapixel camera
-
product
Loop Resistance Measuring Device According to DIN EN 61557-3 (VDE 0413-3)
PeakTech Prüf- und Messtechnik GmbH
A loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.
-
product
Automation
Applied Automation Technologies, Inc
AAT offers suite of software which can be used to automate manufacturing systems with the dimensional measurement feedback and allow multiple systems such as machine tools, measuring machines, shop floor gages and part loading robots to work together.
-
product
Electrical Creep and Rupture Testing Machine
ECR Series
Jinan Testing Equipment IE Corporation
This series of computer control electronic creep and rupture testing machine is newly designed with full-digital measuring control system to meet the standards of GB/T2039, GB//T20120, EN ISO 204-2009 and ASTM E139 etc. The electronic creep and rupture testing system can perform not simply creep. stress-rupture test and stress relaxation test on metals under room or high temperatures, but also low cycling test & creep fatigue test. The electronic creep and rupture testing machine is widely used for quality control in factories, material research in R&D department and teaching in universities,
-
product
Spectral Sensitivity Measurement
It is a device which measures the spectral sensitivity characteristics and quantum efficiency of various solar cells by irradiating solar cells with monochromatic light of constant energy and constant photon without wavelength dependence. We are constantly monitoring irradiation light quantity with our real real time light quantity monitor control system and are not influenced by fluctuation of light source, so it is a well-established control system with excellent measurement stability and measurement reproducibility.
-
product
Low Noise Amplifier
1010
A low noise, DC-coupled amplifier is packaged in a rugged, die-cast aluminum case with BNC connectors enabling input and output. Provides very low voltage noise and current noise in the critical region of 0.1 Hz to 10 Hz making this the ideal amplifier for thermopile detectors in sensitive systems design and laboratory experiments.
-
product
Single-functional testers
3110
The MI 3110 EurotestIM is a perfect tool for testing of permanent integrated or portable Low Voltage Electrical Installa-tions supplied by Generator or Transformer and protected by an IT earthing system. Designed for simple but efficient safety testing of Integrated IT Earthing System powered with LV Generator or Transformer! With a single, pre-programmed AUTO SEQUENCE® with sub-tests and adjustable limits it is possible to perform all the necessary verifications of safety limits of a specific LV IT installation.
-
product
High Voltage Fiber Optic Probe, 150 MHz Bandwidth
HVFO108
- Ideal for GaN and SiC devices- Highest system accuracy- Fastest rise time- High CMRR - 160 dB
-
product
In-Process Wafer Inspection System
7945
Chroma 7945 wafer chip inspection system is an automated inspection system for pre and post diced patterned wafers. Change kits enable switching between various applications by allowing different carriers including metal frame or grip ring.
-
product
Data Loggers
For fleet testing or endurance testing – IPETRONIK data loggers are employed worldwide within some of the most extreme, extended use environments, with technologies that offer unique capabilities for the effective measurement of drivetrain, engine cooling, in-vehicle climate control, HVAC systems and other challenging applications. Our loggers provide dependable data acquisition, also in hybrid and electric vehicles.
-
product
Electric Vehicle Module Test System
FTV
Drive simulations with standard Electric Vehicle tests: FUDS, SFUDS, GSFUDS, DST and ECE-15LBattery Module TestingStart/Stop TestingTraction Battery TestingSupercapacitor / Ultracapacitor TestingDrive Cycle Testing
