-
product
PXIe-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
780587-12
PXIe, 7-Channel, 10 A PXI Signal Insertion Switch Module—The PXIe‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
product
Compact Temperature Calibrator
CTC Series
AMETEK Sensors, Test & Calibration
CTC Series Compact Temperature Calibrator from AMETEK Sensors, Test & Calibrations is engineered for “advanced simplicity,” incorporating a number of useful features that greatly extend the range and functionality of the popular temperature calibrator. The CTC Series offers an easy-to-read, full-color display with improved navigation that provides easy access to the calibrator’s latest features. The CTC Series now contains an auto step function with up to 12 preset temperature points, an optimized switch test with automatic up and down test runs, assisted manual calibration using pre-defined temperature points, and memory to store up to 5 calibration processes.
-
product
PXIe-2525, 64‐Channel, 2 A, Multibank, 2‐Wire PXI Multiplexer Switch Module
780587-25
64‐Channel, 2 A, Multibank, 2‐Wire PXI Multiplexer Switch Module —The PXIe‑2525 is a high‐density PXI multiplexer switch module that is ideal for routing signals within automated test systems. It uses electromechanical relays to perform immediate switch operations in one of the following 2‑wire multiplexer configurations: 16 bank 4x1, octal 8x1, quad 16x1, dual 32x1, and 64x1. The PXIe‑2525 also features onboard relay counting for relay monitoring.
-
product
Multiplex Bus Switch
MBX1553
Curtiss-Wright Defense Solutions
The Curtiss-Wright MBX1553 Multiplex Bus Switch enhances almost any MIL-STD-1553 system by providing a "virtual patch panel" housed in a 19" rack-mountable 1U chassis. The MBX1553 eliminates time-consuming bus rewiring between different avionics simulations and test scenarios.
-
product
PXI Switching Instrumentation
GENASYS
Marvin Test Solutions’ switch card portfolio includes matrix, multiplexer, and RF multiplexer configurations. 3U and 6U PXI switch cards feature easy to use, reliable, and integration-friendly D-sub style interface connectors – a feature unique to Marvin Test Solutions PXI switch cards. GENASYS switch cards are compatible with MTS’s family of GENASYS Switching and Switching/Digital Subsystems, featuring integrated MAC Panel SCOUT receivers.
-
product
PRO8 Modular Laser Diode Platform
Thorlabs offers the PRO8 modular test and measurement platform in 2-slot and 8-slot configurations. These customizable bench top chassis let users build a compact fiber or laser diode testing platforms for their lab or factory floor. Modules include lasers, TEC controllers, optical switches, and current controllers.
-
product
PXIe-2529, 128-Crosspoint, 4x32 OR 8x16, 2-Wire PXI Matrix Switch Module
780587-29
128-Crosspoint, 2-Wire PXI Matrix Switch Module—The PXIe‑2529 is a high‐density PXI matrix switch module that you can configure as either a 4x32 or an 8x16 2‑wire matrix by using different terminal block accessories. It uses electromechanical relays that offer excellent performance for high-power signals and low thermal offset for accurate measurements at low-voltage levels. The PXIe‑2529 also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
Low PIM Coaxial Switch, DC to 20 GHz, SP6T
87106Q
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87106Q is a low PIM SP6T coaxial switch, operating from DC to 20 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
PXI Versatile Multiplexer, Solid State, 250mA, 40V
40-682A-002
The 40-682A-002 is a very high-density versatile PXI Multiplexer module featuring a wide range of selectable switching configurations with 250mA current and 40V voltage handling. The 40-682A is especially useful where a high-density MUX array is required that can adapt to different test configurations for different test targets, or where a test system may have to be reconfigured in the future.
-
product
Hand-Held SCSI CABLE TESTER
ST1000
The ST1000 SCSI Cable Tester is designed with an emphasis on simplicity of use. Connect a cable, press a switch and the LCD indicates the test results within 5 seconds. In addition to Continuity and Integrity, the ST1000 also tests to determine that the critical REQ and ACK signal pairs are located in the inner layers of the cable.
-
product
Signature Surge Tester
TSM
Compact cabinet that contains a multi-position carry/tilt handle and a rear plastic snap-on cover for cable storage and transportation in the shop or in the field. Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope and includes a built-in 3 phase test selector switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
product
384x384 Port Software-Defined Optical Circuit Switch
SERIES 7000
The Polatis Series 7000 Network Optical Switch is the largest-capacity, highest-density, highest-performance and most reliable non-blocking all-optical matrix switch available in the industry. The Series 7000 384x384 all-optical circuit switch is designed to meet the most demanding applications with exceptionally low optical loss, compact size, and fast switching speeds. With support for Software-Defined Networks (SDNs) via embedded NETCONF and RESTCONF control interfaces, the Series 7000n can r...show more -
product
Cable Test Van
BAUR Transcable 4000/S 70-3
BAUR Prüf- und Messtechnik GmbH
Transcable 4000/S 70-3. The transcable 4000 70 kV 3/S cable test van varies in comparison with the transcable 32 kV - 3S in the 70 kV voltage level. The system is controlled with the MGS semi-automatic control unit. The high voltage switch unit is 3-phase, air and solid matter insulated and safe to touch.
-
product
Portable Dynamometers
With the Portable MD-AWD-500, you have a portable drag strip that can handle just about any 2WD or AWD car on the street. Equipped with a drag racing timing system, multiple displays, and Mustang’s DragSim software, the portable MD-AWD-500 is sure to draw large crowds where ever it appears. One thing is for sure, a dyno draws big crowds when it shows up at an event. There is something about watching the wheels spin and listening to an engine at full throttle that captures people’s attention. Add...show more -
product
EBIRST 23 X SMB Verification Fixture
93-011-101
The 93-011-101 23 x SMB Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
PXI Single 10 Channel MUX, XLR Connectors
40-735-902-S2
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the de...show more -
product
PoE Voltage Monitor Detect & Verify
PE-400
PE-400 is specific to test and verify PSE or Ethernet outlet either a standard/active PoE or a NON-standard/passive PoE to avoid damaging Non-PoE device as well as monitor and display available Voltage simultaneously. It built-in PoE interface controller to trigger on 802.3 af, at and bt switch and verify standard PoE type either 802.3 af or 802.3 at, and power source either End or Mid or both, and power polarity as well as display voltage values. The operational voltage which should be measured when installing a new PoE system or when you troubleshooting an existing system.
-
product
EDFA
SPA-2-4X22-WDM EYDFA
Hangzhou Softel Optic Co., Ltd.
*Single/dual input for choice, built in optical switch for dual input, the switching power can be set by the button in the front panel or by web SNMP.*Output adjustable by buttons in the front panel or web SNMP, the range is down 4dBm*Maintenance function of one-time downward attenuation of 6dBm by buttons in the front panel or web SNMP, to facilitate the optical fiber hot-plug operation without turn off the device*Multi- ports output, can built in 1310/1490/1550WDM.*Standa...show more -
product
EBIRST 96-pin SCSI Termination Fixture
93-016-103
93-016-103 eBIRST Termination Fixture is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
Pocket Type Digital Multimeter
MCD-008
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Easy operation with rotary switch.・AC/DC voltage, resistance, continuity check and diode test with full autoranging operation.・3200 count full scale with bargraph display.・Low power consumption with auto power off function.
-
product
HV AC Test Set
SERIES S400 TYPE RX I O/ I OACP
K&S Engineering and Scientific Ltd
The output is continuously variable from zero to 10 kV by means of the panel mounted regulator. An output trip is fitted which operates when the output exceeds 25 mA switches off the test set and operates a neon overload indicator. Primary protection is provided by two panel mounted fuses. The output is protected by the output trip and a magnetic/hydraulic circuit breaker.
-
product
Specialist Test Probes
High Current Test Probes, Ultra-high Current Test Probes,Kelvin Test Probes, High Frequency Test Probes, Switching Test Probes
-
product
System Components
For demanding computational tasks, Rohde & Schwarz offers the versatile, flexible equipment you need for everyday use – from the system controller and switch unit to the test chamber. All feature excellent EMC shielding, reliable test results and modular solutions.
-
product
Signal Integration Systems
Avenue
The Avenue system includes modules for video up/down conversion, audio embedding, synchronization, conversion, routing, noise reduction, protection switches, test signal generators and more. Avenue signal processing modules are used worldwide in broadcast, mobile, satellite, cable, worship and post production facilities. Avenue is a tray-based signal integration system housed in a 1RU or 3RU frame. Any combination of 1.5 Gb/s HD, 3 Gb/s HD, SD, MPEG, analog video and audio processing modules can be used together in the same frame.
-
product
RF & Microwave PXI Switch Modules
These switching systems are used for design validation, reliability and production test including 5G, SD radios, S parameter testing for RF cables, antennas, radar and semiconductor verification.
-
product
PXI 8x9 RF Matrix 500MHz 50 SMB
40-725-511
The 40-725 is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz (50Ω version). The 40-725 is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connections, these disconnect the matrix from the external test fixture maximizing isolation and RF performance.
-
product
LOADpro Dynamic Test Leads
180
*LOADpro Test Leads load the circuit to see if current can flow. *By loading the circuit, LOADpro makes a voltage drop test “on the fly”. *Just press the switch – the test results can not lie. *Use LOADpro w/your DMM and follow our test method - you will find wiring faults quicker. *LOADpro Test Leads feature SteadyPin Probe Tips, which allows the probe to sit firmly on a male ECM or connector pin. *LOADpro are OEM approved – finds corroded circuits fast!
-
product
PXI 3A Power MUX BRIC, 6-Channel, 24-Pole
40-571-103
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
PXI 8x9 RF Matrix 250MHz 75 SMB
40-725-751
The 40-725 is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz (50Ω version). The 40-725 is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connections, these disconnect the matrix from the external test fixture maximizing isolation and RF performance.
-
product
Test Sockets
socket design as per customer specificationsquick + easy socket changehigh-performance spring probesdesigned for high frequency up to 16 GHz-55C/-67F to 150C/302F temperature rangemanual/automatic application optionssmall socket footprintone socket base for each insert (3x3 to 9x9 QFN)one-click switch from engineering to production socket modedevice dependent standard socket frame with changeable insertmore than 500,000 compression cyclesKelvin test applicabilitytool-free insert + actuator exchanges0.3 mm minimum lead pitchQFP extender available