Standards
A controlled reference or acknowledged technical criterion.
See Also: IEC, IEEE, Mil, Interoperability Test, Compliance
-
product
Waveguide Calibration Kits
Designed to provide accurate calibration of vector network analyzers (VNAs) that are used for measurements in standard rectangular waveguide from 2.6 to 50 GHz (WR284–WR22).
-
product
IEC60068-2-75 Spring Operated Impact Hammer
CX-T04
Shenzhen Chuangxin Instruments Co., Ltd.
This Spring Impact hammer is strictly designed according to IEC60068-2-75, IEC884 and UL1244 GB/T2423.55-2006, GB4706.1, GB8898 and GB7000 standards. It is used to test the mechanical integrity of product enclosures. After applying the impact with the hammer, the product is examined with accessibility probes to determine access to shock, energy, and injury hazards. Built in exact accordance to IEC\EN, \UL\CSA and other international Standards.
-
product
Voltage Dips and Interruptions Generator
CSS61000-11
The voltage dip and interruptions generator is specially designed according to the characteristics and requirements of EMS measurement under a sudden reduction or interruption of the voltage at a point, CSS61000-11/ CSS61000-11T used a big LCD in both English and Chinese operating interface. They have more fine performance such as high reliability, convenient operation, and full meet the standard requirements of IEC 61000-4-11, EN 61000-4-11 and GB/T17626.11
-
product
Optical Modules
VI Systems GmbH introduces the fiber coupled 850nm vertical cavity surface emitting laser (VCSEL) transmitter module VM64-850M for data rates of up to 80 Gbit/s. The transmitter module features a V-connector for the electrical input signal and for the optical output a 50/125 multi mode fiber which is terminated with a standard FC/PC connector. The left picture below shows the module. The picture on the right shows an optical eye diagram at 32 Gbaud (64 Gbit/s) in a back-to-back test configuration as tested by partners at the Heinrich Hertz Institute in Berlin.
-
product
Transistor-Level Defect Simulator
Tessent DefectSim
Tessent DefectSim is a transistor-level defect simulator for analog, mixed-signal (AMS), and non-scan digital circuits. It measures defect coverage and defect tolerance. Tessent DefectSim is perfect for both high-volume and high-reliability ICs. Tessent DefectSim replaces manual test coverage assessment in AMS circuits needed to meet quality standards such as ISO 26262 and provides objective data to guide improvements in DFT. Tessent DefectSim dramatically reduces SPICE simulation time compared to simulating every potential defect.
-
product
Telecom & Data Test
Electro Standards Laboratories
iagnostic tools such as Breakout Boxes/Interface Analyzers designed for use at the data interfaces of modems, multiplexers, terminals, and computers. Electro Standards Laboratories' Series of Breakout Boxes/Interface Analyzers are virtually indestructible and compatible with RS232, HSSI(SCSI-2), EIA/TIA RS530 interfaces.
-
product
Milli-OHM Meter
MR-30
*Double LCD Display*300,000 counts resolution*Measurement Range: 30mΩ~3MΩ*0.05% accuracy*20 Standard User setting memory sets*Sorting function and Relative percentage function*PASS/FAIL test result alarm*Computer Remote Manual and Auto Scan function*Manual and Auto Channel select*Sampling Rate: 30 sample/sec*High Resolution Temperature compensation and measurement*DUT Four-wire method*USB interface
-
product
Roughness Tester
Compatible with four standards of site to measure surface roughness ofvarious machinery-processed parts, calculate corresponding and clearly display allmeasurement parameters. When measuring the roughness of a surface, the sensor is placed on the surface and then uniformly slides along the surface by driving the mechanism by the sharp built-in probe. This roughness causes displacement of the probe which results in change of inductive amount of induction coils so as to generate analogue signal, which is in proportion to the surface roughness at output end of phase-sensitive rectifier.
-
product
Durometers
Standard Test Method for Rubber Property, Durometer Hardness. This test method covers twelve types of rubber hardness measurement devices known as durometers.
-
product
Omega Fiber Optic Connector
Teledyne lmpulse-PDM's Omega Series offers any combination of multi-mode or single-mode optical ways and 16 AWG electrical ways from a single way through to seven ways. Electrical pins are part of the CCP and the mating sockets are part of the FCR, CCR or BCR. Connectors populated with both electrical and optical ways will be populated in a standard Teledyne lmpulse-PDM format to facilitate interchangeability between batches. This information can be provided at the time of quotation.
-
product
Acoustical Measurement System
MLSSA
MLSSA is the industry standard loudspeaker measurement system and the MLSSA Speaker Parameter Option (SPO) is the industry standard for measuring the Thiele-Small parameters of loudspeaker drivers. MLSSA and SPO both include QC (Quality Control) PASS/FAIL functions for high-speed automated production line testing of loudspeakers and drivers.
-
product
S2 Penta Sensors
ULP-S2 PCI/V
Optomistic Products’ best-selling Sensor, the ULP S2 Penta Sensor, is relied upon for its versatility in accommodating most LED color and intensity test applications. Implemented in a unique and customizable 2-Part solution, the S2 Penta Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a singl...show more -
product
Microwave Testing
1100B
The Model 1100B Picoprobe sets new standards in microwave probing performance. Benefiting from coaxial techniques, which have inherent low loss and low dispersion characteristics.
-
product
SPSR-2030 (200-3000nm) Super Pure Spectral Radiation Scanning Analyzer
SPSR-2030
Hangzhou Everfine Photo-E-Info Co., LTD
SPSR-2030 adopts double-monochromator design, which can realize super-pure&fine full-spectrum scanning ( 200-3000nm), the test parameters including but not limited to spectral power distribution, peak wavelength, dominant wavelength, CCT (correlated colour temperature), CRI (color rendering index), SDCM (standard deviation of color matching), color purity, and etc.
-
product
Hydraulic testing solutions for Engineering Components
The unit illustrated to the left here allows automatic pressure testing of gas cylinders to BS and DOT standards. The system includes automatic weighing, filling, testing to 500 bar with expansion measurement, and full mechanical handling for up to 180 gas cylinders per hour.
-
product
In-Head RTD Temperature Transmitter
SEM203/P
The RTD in-head mounted temperature transmitter connects to any standard pt100 resistance sensor and converts the linearised temperature to a (4 to 20) mA signal.
-
product
2.5” SATA3 – RunCore Consumer SSD "Sprinter Series"
RunCore Innovation Technology Co. Ltd.
Standard 2.5” SATA3 (6Gbps) Solid State Drive (SSD) is a high capacity solid-state flash memory product that complies with the SATA 6Gbps standard and is functionally compatible with a SATA hard disk drive. It is a standard SATA product that supports both 7mm and 9mm thickness.
-
product
Silicon Diodes
DT-670 Series
DT-670 Series silicon diodes offer better accuracy over a wider temperature range than any previously marketed silicon diodes. Conforming to the Curve DT-670 standard voltage versus temperature response curve, sensors within the DT-670 series are interchangeable and, for many applications, do not require individual calibration. DT-670 sensors in the SD package are available in four tolerance bands—three for general cryogenic use across the 1.4 K to 500 K temperature range and one that ...show more -
product
Environmental Enclosures
TSI’s DustTrak™ Environmental Enclosure models 8535 is designed to protect the standard DustTrak models (8530, 8533, 8530EP and 8533EP) when monitoring outdoors or in hazardous environments
-
product
Precision Multirange Voltage Transformers
WP-36000
The WP-36000 Transformer is primarily a laboratory standard. The high degree of accuracy and multiplicity of ranges makes this transformer the standard for precision calibration work. With the aid of this transformer, very accurate determination can be made of the ratio and phase angle characteristics of voltage transformers having ratings from 14,400 to 36,000 volts.
-
product
Plug-On Transmitter
DPR
This unique plug-on transmitter design will ideally match any microphone or line level source via a standard XLR connector. The DPR can tune in 100 kHz or 25 kHz steps across the UHF television band from 470.100 to 607.950 MHz, with a selectable output power of 25 or 50 mW. The purely digital architecture utilizes AES 256-CTR encryption for high level security applications.
-
product
RF and Microwave Circulators
Chengdu KeyLink Microwave Technology Co., Ltd.
RF Circulators from KeyLink Microwave are passive 3-port microwave devices designed to provide isolation between transmit and receive signals for radar, satellite communication, and telecommunication applications. These microwave circulators can control the signal direction and flow inside an RF circuit. KeyLink provides broadband RF circulators spanning the frequency range of 1 GHz to 18 GHz in varying bandwidths, tailored to cover all standard and popular bands commonly used throughout the market place.
-
product
Energizer SILVER Vibration Exciter for Buzz, Squeak & Rattle (BSR) Testing
Energizer SILVER
The Energizer SILVER Series is part of a family of extremely quiet vibration exciters. The Series is ideally suited for the support of subjective and objective BSR evaluations according to industry test specifications, such as GMW14011, GM7293TP, BMW PR311-2 or PSA “Specification bruit parasites”, as well as several Hyundai Engineering Standards. With availability in four unique models and sizes, the Energizer Series is expressly designed to support such evaluations, while reducing the risks of measurement uncertainty caused by unwanted vibration exciter noise occurring within the BSR test environment.
-
product
Bolt Extensometers for Proof Load Testing
Model 3565
Jinan Testing Equipment IE Corporation
The Model 3565 uses hard conical points to contact the bolt at the center of the head and at the bottom. It is fully adjustable for different length bolts ranging from 25 mm (1 inch) in length to 150 mm (6 inches) standard. Extension beams are available for longer bolts. The standard maximum measuring range is 1.25 mm (0.05 inches). Generally, on longer bolts this extensometer will be self-supported without requiring any centering marks or punch marks on the bolt. For shorter bolts these marks m...show more -
product
Waveguide Bends
Fairview Microwave’s lines of precision waveguide bends are widely used in applications such as high efficiency RF, microwave and mm-wave transmissions, satellite and military communications, radar, telecom, instrumentation and test benches. In waveguide systems that require a signal to turn or bend 90 degrees, Fairview’s waveguide bends are used to facilitate that bend or turn without degrading the transmission signal. These WG bends operate from 5.85 GHz to 90 GHz across 12 frequency bands and...show more -
product
Capacitor Leakage Current/IR Meter
Chroma 11200
Chroma Systems Solutions, Inc.
The 11200 Capacitor Leakage Current / IR Meter is mainly used for electrolytic capacitor leakage current testing and aluminum-foil withstand voltage testing (EIAJ RC-2364A). The 11200 can also be used for active voltage checking or leakage current testing of absorber, Zener diode, and Neon lamp etc. With the standard RS232 interface, optional GPIB & Handler interfaces, high speed and stable measurement capabilities, the Chroma 11200 can be used for both component evaluation on the production line and for fundamental leakage current or IR testing for bench top applications.
-
product
DMX to Analog Interfaces
The MTX-DE48 decodes signals from DMX control desks to analog dimmers. It is used to integrate DMX controllers into existing analog installations. The standard 0 to 10V output is compatable with many LED drivers. Output may be adjusted up to 28V for use with some older dimmer systems. A negative output voltage option is also available.
-
product
PCI-5421, 100 MS/s, 16-Bit Waveform Generator Device
778692-03
The PCI‑5421 can generate user-defined, arbitrary waveforms and standard functions, including sine, square, triangle, and ramp. This arbitrary waveform generator can generate signals from -6 V to +6 V and uses direct digital synthesis (DDS) to precisely generate waveforms. The PCI‑5421 also features advanced synchronization and data streaming capabilities.
-
product
HMI Displays and Panels
Panasonic Industrial Devices Sales Company of America
Panasonic is a leading supplier of HMI Displays And Transparent Touch Panels. A user's experience with displays and touch panels is critical to the success of any device, so Panasonic provides bright, sharp and flexible interface capability with all available products in this category.Panasonic offers both standard and custom devices based on the interface required for the application. Explore Panasonic HMI Displays and Transparent Touch Panels here and then contact a local Panasonic Sales Representative to discuss customization and design in assistance.
-
product
Calibration Pulse Processor
2401
TESCO’s Calibration Pulse Processor (Catalog No. 2401) adapts to any Next Generation three phase test board to directly calibrate with three independent single phase standards.