Showing results: 991 - 1005 of 1087 items found.
-
Curtiss-Wright Defense Solutions
From miniature avionics bus recorders to high-speed, high-capacity units with customizable interfaces, we use our decades of experience designing and manufacturing flight test and monitoring recorders to deliver solutions that meet the newest standards. All recorders feature solid-state media (integrated or removable), tightly integrated replay and analysis software, and industry-leading technology, and can be used seamlessly with our aerospace instrumentation test and monitoring product line. They can record data in a variety of formats, including DARv3, Chapter 10, iNET-X, IENA, and PCAP, and are proven in-ground, flight, and space applications, such as flight test, mission recording, aircraft engine monitoring, health and usage monitoring (HUMS), and aircraft condition monitoring systems (ACMS).
-
TTTech Computertechnik AG
The TTEDevelopment System A664 supporting the ARINC 653 interface is an out-of-the box starter kit for integrating TTEthernet’s deterministic network technology with the time and space partitioned real-time operating system VxWorks 653. The easy-to-use and ready-to-run solution includes hardware and software as well as a Distributed IMA demo application showing deterministic communication among the different real-time operation system partitions. The system supports up to 1 Gbit/s speed, enables event-driven Ethernet (IEEE 802.3) as well as rate-constrained (ARINC 664 part 7) and hard real-time (Time-Triggered Ethernet SAE AS6802) communication on the same network with the option to synchronize IMA modules using the fault-tolerant TTEthernet network time base.
-
Model 200IR -
OAI
The OAI Model 200IR Mask Aligner is a tabletop system that requires minimal clean room space. It is a cost-effective alternative for R&D or limited scale, pilot production. Utilizing an innovative, air bearing / vacuum chuck leveling system, the substrate is leveled quickly and gently, for parallel photo mask alignment and uniform contact across the wafer during contact exposure. The Model 200IR Mask Aligner is capable of one micron resolution and alignment precision. It has an alignment module which features mask insert sets and quick-change wafer chucks that enable the use of a variety of substrates and masks without requiring tools for reconfiguration. The alignment module incorporates micrometers for X, Y, and z-axis.
-
GX7100e Series -
Marvin Test Solutions, Inc.
The GX7100e Series are 14-slot combination PXIe chassis that accommodate a 3U PXIe embedded controller or a MXI express controller as well as 3U & 6U PXI / PXIe insruments in 4U of rack space. The GX7100e’s unique format includes seven 6U slots and seven 3U slots arranged horizontally to reduce the overall size of the chassis, providing the versatility and high-density necessary to address many PXI / PXIe applications and requirements. The backplane architecture supports Gen 2, 4x4 PCI Express bus signaling and the use of both x1 or x4 system controllers. By offering a combination of PXI-1, Hybrid, and Express slots, the GX7100e offers users the ultimate in flexibility for general purpose as well as high bandwidth test needs.
-
Advanced Microtechnology, Inc.
Advanced Microtechnology has extended the application of its Optimum product line with theintegration of ARC5 imbedded test functions. Up to 40 controllers may be independently powered and monitored for functionality using the process test interface of the Optimum WinAOS application. Each part may have 2 separate biases featuring both current and voltage monitoring. Independent test is implemented through a standard JTAG interface. A separate serial clock and command interface may be used if required to provide device initialization sequences. JTAG control is muxed to each part through the use of an independent clock for each part. All of the ARC processor registers and memory space may be tested through the JTAG I/O.
-
Model 8256 -
Pentek, Inc.
- Video: AOC 2021 Mercury's Model 8256 SOSA Aligned Dev. Platform and RFM3202 Microwave Transceiver- Video: Model 8256 3U VPX SOSA Aligned Development Platform, multi-vendor operation demonstration- Video: Model 8256 3U VPX SOSA Aligned Development Chassis- Developed in alignment with the SOSA™ Technical Standard- Ideal development platform for Pentek's- Model 5550 8-Channel A/D & D/A Zynq UltraScale+ RFSoC Processor - SOSA Aligned 3U VPX- Model 5553 8-Channel A/D & D/A Zynq UltraScale+ RFSoC Processor - SOSA Aligned 3U VPX- 8-slots provide space for a range of acquisition and processing boards- Optional rear panel RF and optical connections- Compatible with the Quartz product family
-
Ono Sokki
•Adopted FAMS-R5 system for motorcycle chassis dynamometer•Gas emission test, durability test, performance test, and environmental test are applicable to various vehicles (motorcycle, tricycle,ATV).•Newly designed measurement unit in a test room makes measurement easier.•Reduction of initial cost, space saving, and less maintenance items by lineup of electric inertia type chassis dynamometer that can be used for small to large vehicles.•Components necessary for emission test are included, such as front wheel holding unit, engine cooling fan, drivers display.•Application software necessary for emission test is installed, such as road resistance setting software, drivers aid,gas emission data processing software, rear axle output data processing software.
-
WDM -
IXI Technology
It is highly desirable to reduce the number of cables required to communicate between spaces on Navy ships due to increased weight, cost and maintenance concerns. To reduce weight and expense, copper-based NTDS parallel and serial type cables can be converted to fiber optic and multiplexed using Wavelength Division Multiplexing (WDM) technology. WDM technology allows for multiple fiber optic wavelengths to be combined in a single fiber and then separated back to individual fibers at the distant end. Using Coarse WDM (CWDM) which utilizes wavelengths 20nm apart ranging from 1271 nm to 1611 nm, provides for up to 18 optical wavelengths to be combined into a single fiber. Optionally Dense WDM (DWDM) can be used allowing for up to 160 optical wavelengths.
-
RCT1A and RCT5A -
Powertek LLC
These probes have great bandwidth ensuring accurate measurement even with harmonically distorted wave shapes. For all RCT1A/RCT models, a NIST, NAVLAP, NPL (UKAS) factory traceable calibration certificate and certificate of conformance is supplied. UL/CSA approved materials are used throughout. Three phase and single phase flexible AC current sensors (rope sensors) are available for fast installation in confined spaces, eliminating the need for Electrical Supply Shutdown. Available outputs are 1A @ 2.5VA and 5A @ 0.5VA, this means long cable lengths from current sensor to signal conditioner allow these low VA ratings to be used, even when feeder cable to energy meter distances are large (up to 98 feet / 30 meters)
-
PLZ-4WL Series -
Kikusui Electronics Corp.
While the PLZ-4WL series succeeds to the superior operability of our conventional model of the PLZ-4W series, the PLZ-4WL series realizes the high speed rise and fall time (slew rate of 50A/µs.) in the range of low voltage with large current. The PLZ-4WL offers six operation modes, and equips with various features such as sequence operation, switching operation, soft-start function, and time and voltage measurement. The PLZ-4WL applies not only for the conventional load test of the CPU power supply, but also it can be applied to even faster current response test. In addition, the PLZ-4WL is a space-saving design (about 50% less volume of the conventional model) that can save the facility space of the testing site, and it can be applied for the single cell testing of the large scale rechargeable battery.
-
Testhouse Ltd
Mobile testing ensures the quality of applications and other digital properties running on mobile devices. The dynamism, complexity and competitive nature of the mobile application space makes it imperative that publishers choose a highly responsive and well-equipped test partner to ensure the greatest user experience of their digital properties across all types of mobile devices.- Mobile testing involves all testing types (functional, performance, etc).- Mobile application testing involves thousands of complex parameters- Mobile applications see faster development iterations and hence have to be tested more frequently than at the normal application SDLC.- DevOps practices become indispensable in mobile testing as you have to anticipate and stay one step ahead of changes in the market
-
MVTec Software GmbH
In the industrial environment, especially in digitalized, automated production scenarios, more and more so-called embedded systems are being used. Embedded devices are small, with compact dimensions, highly efficient, and generate little waste heat. Therefore, they are also suitable for limited space conditions. Due to often harsh environmental conditions, they must be particularly robust and resistant to external influences like massive dust accumulation, strong vibrations, and high humidity or even direct contact with water. Typically, embedded devices are handhelds, smartphones, tablets, vision sensors, smart cameras, smart sensors and single board computers. If the systems have integrated machine vision software, they can be used for a wide range of image processing applications. This is known as embedded vision.
-
SEN-36001 -
Playing With Fusion Inc
Highly integrated breakout board for the ST Micro VL6180X Time of Flight (ToF) range finder sensor. This sensor has many uses in the robotics, cell phone and gesture recognition space. It has two programmable GPIO pins, and most importantly, measures absolute distance up to 100mm. The SEN-36001 includes a VL6180X IC centered between two 4-40 sized mounting holes with onboard 2.8V LDO and voltage translation to handle interface voltages from 3V to 5V. The board is interfaced via an I2C interface and all IC pins have been broken out to a 0.1" pin header. Example code for the Arduino platform is available below and includes code for both the proximity measurement and ambient light sensing capabilities.
-
Kaypee Udyog
- Suitable for carrying out different quality control tests under controlled conditions of temperature and humidity.- The excellent quality of door packing for the external door.- User oriented design of shelves makes you adjust each space of shelves without difficulty.- Inner chamber and trays are made of stainless steel (S.S.-304 Grade)- Outer wall of mild steel sheet duly powder coated.- Mounted on caster wheels for easy portability.- High grade glass wool insulation between outer and inner chamber for minimal thermal loss.- Front double walled door is provided with lock and key arrangement.- A self-cooled air circulation fan is fitted to maintain uniform temperature and humidity conditions throughout the chamber.
-
A63 -
La Marche Manufacturing Company
The unique design of the LaMarche A63 Series DC-DC Converters will allow you to utilize your 48V, 24V, and/or 12V equipment at a site where 130V batteries are installed. This will save battery, charger, and installation costs as well as reducing maintenance time and optimizing space. The A63 is a compact self contained DC-DC Converter that provides the Modular Power that today's utility substation, process control and telecommunications applications require. The A63 is the building block of these reliable systems using advanced switching technology. Its filtered output provides the clean power required for sensitive loads. The A63 DC output is available in 48V(15 amps) and 24V (30 amps) rated at 750W, or 12V(30 amps) modules rated at 375W.
