-
product
Bridge Trainer
Salicon Bridge Trainer to measure unknown Resistance/Capacitance by balancing two legs of a Bridge Circuit. With the of DC Source, Student can set the null point by using different combinations of variable Resistors Circuit Diagram is provided on-board for Teaching/Training.
-
product
Single Slot Intelligent Interface Card
IIB-3910-CPCI
The IIB-3910-CPCI is a single slot intelligent interface card providing complete STANAG 3838 and STANAG 3910 test, simulation and bus analysis capability for the CompactPCI Bus. The IIB-3910-CPCI supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with powerful multi-level triggering capability. Full error injection capability in both 3838 and 3910 modes is provided ...show more -
product
Compact Vibration Generator
The compact vibration generator is used for calibration of a vibrometer, measurement of mechanical impedance, excitation source for modal analysis and reliability test of a small light specimen. In particular, EMIC uses the world's first ceramic armature for the 512-D and 513-D vibration generator,making it possible to excite up to high frequency of 30 kHz (513-D can excite up to 24 kHz).
-
product
Pressure Transducer Module
PTM-1000
Advanced Thermal Solutions, Inc.
The PTM-1000, Pressure Transducer Module, is a four-channel test instrument for measuring differential pressure in enclosures where air flow integrity is critical to proper performance. As the demand for more energy efficient cooling grows, the need for measuring the pressure at each source of heat generation will follow.
-
product
Analysis and Visualization of Arbitrary Test Reports and Result Data
TEST-GUIDE
Test execution in development projects leads to the accumulation of various reports and data. Test automation intensifies this, producing very high numbers of test executions, which are distributed over several users and test environments. This multitude of test results from different sources can be efficiently managed and analysed using TEST-GUIDE.
-
product
Near Field Probes 30 MHz up to 3 GHz
RF6 set
The RF6 near field probe set consists of 2 passive magnetic field probes and 2 passive E field probes for measurements in the development phase of the E-field and magnetic field in the range from 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF6 set allow a step by step localization of interference sources of the RF magnetic field and RF-E-field on an assembly. From a larger distance the electromagnetic interference is detected by RF-R 50-1 for the magnetic field and by RF-E 0...show more -
product
Handheld Broadband Noise Generator
NS-1
The Model NS-1 is a handheld broadband white Gaussian noise source. It generates a wide, even, RF noise-signal. The NS-1 is popular for testing network components and aligning a building's coaxial cable network. The NS-1's noise-signal is also used to provide the RF source for measuring insertion loss of cable, splitters, taps and more.
-
product
Environmental Vibration
The monitoring of environmental and ground vibration is required because vibration can cause both damage to local structures and distress to nearby residents. There are many sources of environmental vibration where monitoring is required, common sources are Civil Engineering Works, Quarrying and Blasting, Construction Sites and road works.
-
product
Tow Doctor™ Trailer Side Test Unit
50928
Hopkins Manufacturing Corporation
Specifically designed so that one person can make sure a trailer has been wired properly and all functions are working. Plug the Tow Doctor™ into the trailer connector and the power cord into a battery source and cycle through the trailer lighting functions. Includes 7 Blade, 6 Round and 4 Flat test connectors and durable carrying case.
-
product
SLED Optical Source
JW8006 Series
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
SLED(Super luminescent light-emitting diode) is a super broadband optical source which is designed for fiber sensor;, optical fiber gyroscope, lab application field. It has the feature as broaden bandwidth, customizable center wave length, high output power, etc. Benchtop (for lab), standard module(150*125*20mm, with modulation function) and mini module(90*70*15mm) is available. The key component is employed the FWHM bandwidth up to 40nm high power SLEDs to ensure the spectrum performance. Stability is ensured by unique ATC and APC circuit. The output power is adjustable by RS232 or RS485 port.
-
product
Heat Detector Testing
Solo 461
Functional checking of heat detectors, with a genuine heat source, is now required by major national standards around the world. Testing with heat sources not designed for the purpose can be both dangerous and damaging. The Solo range of heat detector testing equipment, designed specifically for the purpose, provides a genuine professional’s solution.
-
product
Biosensor isoPod with USB
EPU352
A compact signal conditioner for monitoring low current, two-electrode (anode and cathode) amperometric sensors. By setting the polarization voltage to zero it can also be used as a zero resistance ammeter (ZRA).Electrical isolation ensures that readings are not influenced by nearby current sources such as conductivity, or voltammetric electrodes.
-
product
Sensor
Lepton
The FLIR Lepton™ is the most compact longwave infrared (LWIR) sensor available as an OEM product. It packs a resolution of 80 × 60 or 160x120 pixels into a camera body that is smaller than a dime. This revolutionary camera core is poised to equip a new generation of mobile and handheld devices, as well as small fixed-mount camera systems, with thermal imaging capabilities never seen before. Lepton contains a breakthrough lens fabricated in wafer form, along with a microbolometer focal plane arra...show more -
product
EMI Receiver
KH3939
Beijing KeHuan Century EMC Technology Co,.LTD
KH3939 type EMI test receiver interference test receiver is fully automatic, is EMI major tool for testing. The frequency range of the KH3939 receiver is from 9kHz to 300MHz , which satisfies the power line disturbance power test. After configuring the artificial power network, the power terminal disturbance voltage test can be carried out. The machine has fast test speed, strong maneuverability, stable performance, Advantages such as convenient test data processing. The KH3939 receiver uses a U...show more -
product
Sola-Check System
Flexible and technically superior solution for measuring UV lamps output with spectroradiometer readings. The Sola Scope accurately measures UV light in the range 240nm to 470nm with clear data on both the intensity and wavelength of the UV source. It can be used as a single key operation radiometer or as a high-powered analysis tool supporting graphical analysis.
-
product
International Power Source
The Interpower® International Power Source (IPS) provides a low-cost, convenient source of AC power at various operating voltages and frequencies found around the world (typically 110-240VAC/50-60Hz) which is important for testing any products that are exported. Output power is delivered through one of two ranges: Low range (10-138VAC) through a standard NEMA 5-20 socket and High range (10-276VAC) through any of the six standard international sockets so that products can be conveniently powered during development or just prior to shipment.
-
product
PXIe-4142, 4-Channel, ±24 V, 150 mA PXI Source Measure Unit
782430-01
PXIe, 4-Channel, ±24 V, 150 mA PXI Source Measure Unit - The PXIe-4142 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote (4-wire) sensing for accurate measurements. The fast sample rate of the PXIe-4142 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules.
-
product
Light Source
LS-HA
provides the stable and smooth wide-band spectral output. It’s proper for most visible to near infrared range measurement. This light source is also designed to be used in the standard measurement package. It ‘s a simple and quick measurement platform.
-
product
Step-Tunable Laser Source, High Power and Low SSE, Basic Line
N7779C
The new N7779C basic line step-tunable laser source is ideal for cost-effective testing of broadband optical devices. It can also serve as a highly stable, tunable local oscillator for receiver testing or transmission experiments.
-
product
Optical Power and Wavelength Meter
OMM-6810B
The OMM-6810B is a power and wavelength meter capable of simultaneously measuring the optical power and wavelength of a laser source. A wide variety of measurement heads cover wavelength ranges from 350 to 1650 nm for power ranges of up to +40dBm or 10W.This meter has standard features such as logarithmic or linear display modes, auto ranging, user calibratable offset, reference measurement capability, analog output and IEEE-standard GPIB interface to make this instrument a cost effective laser diode development or production test tool.
-
product
Systems Engineering Projects
Precision Development Consulting Inc
Furnace Automation, LED Materials System, Batch CVD System, Source Evaluations, Field Audits
-
product
MCB Magnetic (Instantaneous) Trip Test Bench
The test bench is specially built for low voltage- B, C & D curve MCBs. Specially designed custom built jigs are able to accommodate single, double, three and four pole MCBs. Decades of experience has helped us to design current source (transformer) in a special way such that good current regulation and high accuracy is ensured with a variable range without the use of any variable transformer in the system. The product is better than the competition with conventional technology at a lesser price!
-
product
Optical Test Lab
Every object affects or interprets light differently, so appropriate and accurate measurements are needed in order to determine how much light is being produced by a source or cast upon an object. This can be measured with respect to power requirements, as well as how the human eye interprets that light.
-
product
Day Camera Testing
CI Systems' CCD test stations are used to carry out all the necessary tests to verify and compare the quality of a CCD based camera. These stations are based on CI Systems' reflective collimators, Visible Radiation Sources, special targets and integrated software, to project standard patterns with known geometry and intensity to the Unit Under Test. As a result, these stations are turnkey solutions for the CCD camera testing needs.
-
product
Automotive Serial Triggering and Analysis (CAN, LIN) for DSOX1000 Series Oscilloscopes
DSOX1AUTO
The automotive serial triggering and analysis (CAN, LIN) option for InfiniiVision 1000 X-Series oscilloscopes allows you to trigger on either standard or extended CAN message IDs, including the message ID of a remote transfer request frame. It supports triggering on a data frame and allows you to specify message IDs, data and data length for filtering messages of interest. Triggering on active error frames also is supported. In addition, it supports triggering on LIN frame IDs and data, and it includes color-coded parity and check sums errors. You can easily isolate serial packets to find error sources due to hardware or software related problems.
-
product
Medium-Temperature MBE Sources
Medium-temperature MBE sources can be used for for virtually any application—from hot-lip SUMO sources to standard filament for thermal effusion.
-
product
Bidirectional DC Source / Sink With Regenerative Power Supply
LAB / HPR
LAB / HPR DC sources are controllable 19 "bidirectional voltage sources in the power range from 7kW to 1.4 MW. The devices work bidirectional - load and power supply in one, thus energy recovery with high efficiency. As developers and manufacturers, we can also implement your individual wishes in addition to our standard device.
-
product
X-ray Fluorescence Sulfur/Chlorine-in-oil Analyzer
MESA-7220V2
The MESA-7220V2 measures both sulfur and chlorine in petroleum based products using the Monochromatic Energy Dispersive X-ray Fluorescence (EDXRF) method. A monochromatic X-ray source is used in order to obtain an ultra-low noise background which affords the best detection limits for both sulfur and chlorine.The detector window size was increased to collect more fluorescent X-rays and thus achieve lower level ppm values. This provides excellent, repeatable performance at both low and high concentrations of both elements.By adjusting the angle of the graphite crystal, the excitation beam can be measured to excite sulfur in the sample, increasing sensitivity.
-
product
10 MHz to 55 GHz Noise Sources
CNS346 Series
The Spanawave CNS346 Series is designed for precision noise figure measurement applications. The superior VSWR characteristics reduce multiple reflections of the test signals and significantly increase the measurement accuracy of most noise figure set-ups. The CNS346 Series noise sources have broadband coverage and extremely good temperature and voltage stability, for the finest noise figure meter-compatible laboratory standards. Outputs of 6, 15.5 and 22 dB ENR are available, allowing the units to accurately measure noise figures up to 20 ,30 and 36 dB respectively.
-
product
FPGA Mezzanine Card
FMC116
The FMC116 is a 16-channel ADC FMC daughter card which is fully compliant with the VITA 57.1-2008 standard. The FMC116 provides 16 A/D 14-bit 125Msps channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available.
