Showing product results. 586 - 600 of 728 products found.
-
2671A - Shenzhen Chuangxin Instruments Co., Ltd.
*High voltage, large current, high accuracy. *Leakage current, testing time, continuous arbitrarily, well-adapted. *Synchronized display measuring value( time, voltage and current). *Can choose manual or remote control test *High voltage breakdown protection, sound and light alarm, safe and reliable
-
MS 1528 - Meltronics Systemtech
Obstacle Detector is a distance-measuring system based on ultrasonic sound utilizing the LPC2364FBD100. The system transmits a burst of ultrasonic sound waves towards the subject and then receives the corresponding echo. The LPC2364FBD100 integrated analog comparator is used to detect the arrival of the echo to the system. The time taken for the ultrasonic burst to travel the distance from the system to the subject and back to the system is accurately measured by the LPC2364FBD100. Assuming the speed of sound in air at room temperature to be 1100 ft/s, the LPC2364FBD100 computes the distance between the system and the subject and gives the information to buzzer. The minimum distance that this system can measure is eight inches and is limited by the transmitter’s transducer settling-time. The maximum distance that can be measured is 2 meter. The amplitude of the echo depends on the reflecting material, shape, and size. Sound-absorbing targets such as carpets and reflecting surfaces less than two square feet in area reflect poorly. The maximum measurable range is lower for such subjects. If the amplitude of the echo received by the system is so low that it is not detectable by the Comparator. This system is mainly used to replace normal sticks for the visually impaired (blind) peoples. This unit has standard USB 2.0 for mobile interface and has android application for user interface
-
SonicSniffer - ATCP Physical Engineering
SonicSniffer is a portable frequency meter for preventive maintenance of ultrasonic transducers and power ultrasonic stacks, primarily in cutting and ultrasonic welding fields. The SonicSniffer determines the work frequency of the ultrasonic stack analyzing the sound emitted by the equipment during operation. See in the back side of this sheet how to use this information.
-
SIGINT - Argon ST
We design, develop and produce state-of-the-art SIGINT sensors that seek, exploit, identify, and locate sources of RF energy, underwater sound, light, heat and other complex phenomena. These sensors recognize threats, gather intelligence, and allow our customers to make informed, strategic response decisions.
-
CTS Valpey Corp.
Piezoelectric ceramic materials are the active component in nondestructive testing transducers. The material is driven with an ac signal to generate an ultrasonic sound wave that is coupled into an object. The ultrasonic wave is reflected back to the transducer when it encounters a change in density in the material caused by a crack, porosity, or other object with a different density.
-
1106 IM - Standard Electric Works Co., Ltd
● Large LCD : 68 × 34mm (2.677" × 1.338").● True measurement of speaker systems actural impedance at 1kHz.● Three test ranges allow testing of home theater and commercial sound systems.● Measures transformer impedances.● Battery operation.● Low battery indication.● Data hold function.● 0Ω adjustment.
-
1107 IM - Standard Electric Works Co., Ltd
● Large LCD : 68 × 34mm(2.677" × 1.338").● True measurement of speaker systems actural impedance at 1kHz.● Three test ranges allow testing of home theater and commercial sound systems.● Measures transformer impedances.● Battery operation.● Low battery indication.● Data hold function.● 0Ω adjustment.
-
6034 - Associated Equipment Corp.
• Carbon pile tester handles all 6/12 volt batteries• Two large 4.5″ analog meters display amps and volts• DC test leads are 2.5′ 4 AWG cable• Unit comes with manual adjust knob• Buzzer sounds after load is engaged for 15 seconds• Imported
-
Bierer & Associates, Inc
The HI Pot Device is designed to Hi Pot de-energized 15kV class cables. The tool transforms 18 Volts from the battery to approximately 8,000 volts DC. When the battery is installed and the safety switch is in the closed down position, the unit is in voltage detection mode. The unit should be in this position when installing the device, as it will sound a warning alarm if you approach an energized source. When the safety switch is lifted and the toggle switch is switched up, the unit is in the Hi-Pot mode and the high voltage DC is being applied.
-
Selco USA, INC
An insulation monitoring device circuit monitors the un-grounded system between an active phase conductor and earth. It is intended to give an alert (light and sound) or disconnect the power supply when the resistance between the line and ground drops below a set value, usually 50 kΩ (sample of IEC standard for medical applications). The main advantage is that the un-grounded or floating system allows a continuous operation of important consumers such as medical, chemical, military, etc. Most monitors work by injecting low level DC on the line and detecting.
-
ST8662 - Shenzhen Sintech Electronic, Inc.
1.mini PCI&(LPT+USB) 2 in 1. It is fit for MiniPCI slot of laptops and the parallel port (LPT) to which POST codes is output,USB provide power supply.2.The value of four-bit-code PC Analyzer's "initiative code" is specified and it is "0000" or "FFFF"."initiative code" is clear at a glance. While the value of conventional two-bit-code PC Analyzer's "initiative code" is uncertain and man is unable to distinguish accurately by unaided eye.3. Court defects by difference sounds coding with build-in speaker。
-
BAS001 - Larson Davis, Inc.
The BAS001 Source is designed to generate omnidirectional sound fields for making standard compliant measurements including: reverberation time (ISO 3382, ASTM E2235), building acoustics (insertion loss, acoustic absorption area, etc: ISO 140-4 ISO 140-3, ASTM E336, ASTM E90, DIN 55 210). The BAS001 is typically used to saturate a room with a uniform acoustic field. The available high-efficiency power amplifier has no fan for cooling, allowing measurements in quiet environments, like those in reverberation time applications.
-
SparkFun Electronics
Do you have a good understanding of various sensors or need a variety of them for a project? The SparkFun Sensor Kit includes a sensor for just about every job. With everything included in this kit, you'll be able to sense gesture, humidity, temperature, motion, touch, sound, altitude, acceleration and more! These are some of our favorite sensors from each category. But wait, there's more! The SparkFun Sensor Kit now includes several of our sensor boards that feature the Qwiic Connect System for rapid prototyping!
-
TOA Electronics, Inc.
Amplifier is designed to be used in conjunction with optional modules and can be confiugured for up to 8 inputs and 8 outputs. 9000 series modules as well as existing 900 series input modules can be used. The more appropriate modules can be selected depending on applications. Since it comes with two 60W power amplifiers, it can individually perform multi-origin braodcasts. It is equipped with singnal processing and control functions necessary for sound reinforcement, permitting all parameters to be set at the mixer. Settings data can be stored inside the unit and called up using the keys on the front panel.
-
Kaleidoscope - Wildlife Acoustics, Inc.
Kaleidoscope powers through all of your recordings, creating groups of similar sounds called clusters, which significantly reduce analysis time. In addition, its sophisticated spectrogram and audio tools let you quickly verify and label your data.Designed by software engineers and tailored to bat biologists' research needs, Kaleidoscope is an integrated suite of bat data tools designed to help you quickly convert files, sort and categorize bat data by species, verify your findings, visualize your work and easily transform it into reports.