- Taylor Dynamometer, Inc.
product
Data Acquisition And Control System
DynPro2
Demands for data acquisition call for a range of complex requirements that need to come together to meet customer challenges, industry advancements and safety. DynPro2 is a full-featured, testing and measurement system that’s capable of testing a wide variety of equipment including engine, vehicle and industrial component testing.
-
product
Portable Signal Conditioning System
SCS-800
The SCS-800 is a high-performance signal conditioning system for PC-based data acquisition. An SCS-800 system consists of an AC operable chassis and up to 8 multi-channel modules.
-
product
Wireless Measurement System for ETSI & FCC Devices for ISM Bands
TS8997
The R&S®OSP-B157W8 PLUS 7.5 GHz module with up to eight channels is the core of the system and uses a printed RF switch board in solid-state relay (SSR) architecture. It allows flexible operation of the connected DUT (up to eight ports) for power measurements, signal conditioning via the integrated attenuators, couplers and combiners, RF switching to the measuring instruments in combination with the R&S®OSP-B157WX up to 40 GHz and is controlled by R&S®WMS32 software.
-
product
Accelerometers
Analog Devices accelerometers and iSensor® MEMS accelerometer subsystems provide accurate detection while measuring acceleration, tilt, shock, and vibration in performance driven application. Our portfolio leads the industry in power, noise, bandwidth, and temperature specifications, and offers a range of MEMS sensor and signal conditioning integration on chip. Our MEMS-based Circuits from the Lab® reference designs have been built and tested by ADI experts to help you jumpstart your next system design.
-
product
Universal Data Acquisition System
(UDAS/USB2250)
The Universal Data Acquisition System(UDAS) Sensor Interface provides real world data acquisition for your PC via the USB port. 16 sensor inputs in any mix or combination are accepted by the UDAS. No external signal conditioning is required. The UDAS includes configuration and data acquisition software.
-
product
PXIe-4330, 25 kS/s, 24-Bit, 8-Channel PXI Strain/Bridge Input Module
781346-01
25 kS/s, 24-Bit, 8-Channel PXI Strain/Bridge Input Module—The PXIe‑4330 is a simultaneous input module that provides integrated data acquisition and signal conditioning for bridge-based sensors. The PXIe‑4330 includes increased accuracy, high data throughput, and synchronization features, making it ideal for high-density measurement systems. To remove noise, the PXIe‑4330 offers antialiasing and digital filters per channel. Each channel also features an independent, programmable excitation voltage. Additionally, the PXIe‑4330 provides remote sensing, internal bridge completion, and shunt calibration options per channel.
-
product
3-CH RTD Input Module
ND-6013
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS...show more -
product
Signal Conditioning System
SCS-801
The SCS-800 is a high-performance signal conditioning system for PC-based data acquisition. An SCS-800 system consists of an AC operable chassis and up to 8 multi-channel modules.The SCS-800 takes advantage of the increasing capabilities of notebook and desktop PCs by leveraging off the PC's strengths. It provides a high-performance, flexible solution whether used as a conditioning front-end for desktop systems in the factory or as a mobile solution for portable systems in the field.
-
product
Isolated Process Control Signal Conditioning Products
SCIM7B
SCIM7B Isolated Process Control Signal Conditioning Modules provide a complete selection of backpanels DIN rail mounting accessories, interface cables and rack mounting hardware.Each SCIM7B module provides a single of isolated analog input or output. Various input modules accept analog voltage or current signals from all types of field sensors and sources, filter, isolateamplify, linearize and convert these input signals to high-level analog outputs suitable for use in a process control system. Output modules accept high-level analog voltage signals from a process control system, then buffer, isolate, filter, convert and amplify before providing a current or voltage output to a fielddevice.
-
product
Fracture Mechanics Clip-On Gages
Model 3541
Jinan Testing Equipment IE Corporation
The Model 3541 is designed for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. These COD gages conform to the requirements of E1820 (the replacement for E813 and E1737) for JIC and R-curve determination. Special configurations are available to meet the requirements of ASTM E399 for fracture toughness (please consult the factory for these configurations). In addition, the modified...show more -
product
Series 6100 Signal Conditioning, Amplifier, Filter & Analog Output System
I/O modules configure the 6100 to your specific needs. Pacific offers a broad selection of modules providing a high degree of flexibility, accuracy and performance. Series 6100 I/O Modules condition, amplify, filter and output high level signals to external data acquisition systems. Modules are selected according to functional and performance requirements for your application.
-
product
High Speed Device & Flash Programmer
JT 2147 QuadPOD
The JT 2147 QuadPOD high speed device programmer and flash programmer comprises JT 2148 transceiver and four independent, programmable JT 2149 TAP PODs and provides signal conditioning for the DataBlaster series of boundary-scan controllers. Used for gang, parallel, fast testing / Programming of devices.TAP pods can be housed integrally within the transceiver or they can be detached and reconnected via the (optional) one meter extension cable. The JT 2148 transceiver is available in standard (/...show more -
product
High Temperature Diametral Extensometers (1000 C)
Model 3580
Jinan Testing Equipment IE Corporation
This model is for diametral strain measurement with furnace and induction heating systems. Quartz rods and water-cooling allow the unit to be used for high temperature testing of metals, ceramics and composites. With induction heating, this model often can be used without water-cooling. When used in furnaces, the extensometer is often mounted directly to the furnace side cut-out. Optional load frame mounting brackets are available for supporting the extensometer in cases where furnace mounting i...show more -
product
Pressure Sensors
ESCP-MIS1 Sensor
ES Systems has developed a series of medium isolated pressure sensors suitable for applications with harsh environmental conditions where resistance to corrosive fluids or gases is required. Each sensor integrates a MEMS capacitive pressure sensor die, and a CMOS ASIC for the signal conditioning. The MEMS pressure sensor dies are underpinned by ES’s innovative microfabrication process for silicon capacitive sensors.
-
product
Crosspoint Switches
Macom Technology Solutions Holdings Inc.
At MACOM we offer the industry’s largest portfolio of low latency crosspoint switch devices with channel counts ranging from 2x2 all the way up to 288x288, and data rates from 3.2 Gbps to 28 Gbps. Our devices are equipped with signal conditioning technology that enables system designers to use lower cost board materials and components while increasing their system margin.
-
product
2-Channel Front End
BEQ II.1
*Binaural, digital equalizer with 24 bit technology and USB interface.*The digital equalizer BEQ II.1 combines the characteristics of an equalizer, a two-channel front end and an A/D converter into one mobile and very versatile measurement tool.*Binaural, aurally-accurate recordings can be conducted easily with BEQ II. The AES/EBU interface allows a quick and easy expansion into a four-channel system, e.g. with the HMS III or HMS IV. Via the ADAT interface, up to four BEQ II units can be conne...show more -
product
IOLITE LX
IOLITE LX - Embedded Data Acquisition SystemIOLITE LX is an embedded data acquisition system based on a low power Linux based ARM processor with open architecture being able to act like a data logger, real-time system, and signal conditioning frontend, all at the same time.
-
product
Multipurpose Mobile PXI DAQ System
The mobile DAQ system achieves seamless integration among signal conditioning, data acquisition, and synchronization that benchtop instruments would not have achieved. By choosing this system over using benchtop instruments, United Technologies Research Center saved hundreds of thousands of dollars.
-
product
High Volume Manufacturing Handling, Stimulus
ULTRA P
The ULTRA P is a high performance production handler that provides thermal conditioning, full 6 DOF mechanical stimulus and an electrical ATE signal path for testing Micro-Electro-Mechanical Systems (MEMS) Accelerometers and Gyroscopes.
-
product
RS-232 to RS-422/RS-485 Converter
ND-6520
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS...show more -
product
DAQ Systems
Data acquisition systems (DAQ or DAS) collect information from connected sensors and other instrumentation to measure and record electrical and physical quantities, such as voltage, current, temperature, strain, pressure, shock, vibration, distance, displacement, RPM, Angle, and weight. A DAQ System typically consists of sensors, measurement hardware with signal conditioning and an Analog-to-Digital converter, and a computer with programmable software for data logging and analysis.
-
product
VXI Module
VDSP-31
The VDSP31 is a VXI based, multi-channel data acquisition system and digital servo control module. The VDSP31 offers a complete solution for high performance closed loop applications. The VDSP31 has been designed to solve specific problems related to the control of hydraulic actuators. Signal conditioning modules can be combined on a per channel basis to configure the VDSP31 for load or displacement feedback.
-
product
Servo-Pneumatic Asphalt Testing System
All signal conditioning, as well as high-speed data acquisition and control functions are done by the unit and graphically interfaced through CATS, windows based software running on a standard PC. The system is capable of performing the full spectrum of HMA tests: dynamic complex modulus, flow number, flow time, indirect tension, beam flexural fatigue and resilient modulus. These tests are done with the appropriate testing modules. The different testing modules can be obtained after the initial system acquisition at the same discounted price. In addition, guarantees system upgrades in order to meet future standards .
-
product
SLSC and CRIO Modules and Accessories
Our approach to delivering a high-quality Aerospace, Automated Test Equipment (ATE) asset begins with leveraging National Instruments hardware and software standard platforms. Beginning with high quality instrument platforms for standard Input and Output (I/O), we leverage NI’s PXI and Compact RIO platforms. Extending these system is NI’s unique platform for Switching, Loads and Signal Conditioning (SLSC), which allow the standard I/O to be customized for high performance aerospace industry applications.
-
product
MEMS Handler
4664-IH
The ULTRA P is a high performance production handler that provides thermal conditioning, full 6 DOF mechanical stimulus and an electrical ATE signal path for testing Micro-Electro-Mechanical Systems (MEMS) Accelerometers and Gyroscopes.
-
product
PXI Analog Input Module
PXI Analog Input Modules feature multiple analog-to-digital converters (ADCs) as well as built-in signal conditioning. Sample rates range from 5 kS/s/ch to 2 MS/s/ch. You can choose from modules that offer up to 28 bits of resolution and up to 32 simultaneous channels. PXI Analog Input Modules offer different types of isolation and filtering, so you can choose options that meet specific application needs. The modules promote increased accuracy, high data throughput, and are ideal for scalable measurement systems with low and high channel counts.
-
product
Titan Data Acquisition
DAQ
Titan Data Acquisition (DAQ) Systems offer universal signal conditioning, low power consumption, convenient SD card storage, and easy-to-use software. Systems can be purchased as a complete test kit, including custom cables and accessories. Titan products are designed and built in the US.
-
product
Video CODECs
ADV7202
For designers requiring complementary high precision, high speed video digital-to-analog and analog-to-digital converters, Analog Devices offers a single generation of video codecs. Designed to provide analog video input/output capability for proprietary video systems, ASICs, or FPGAs, the ADV7202 supplies raw video conversion and basic analog signal processing and conditioning to allow highly efficient, well partitioned systems architecture.
-
product
Electronics For Signal Processing
PCB Piezotronics manufactures a wide variety of electronics to power ICP®, PE (Charge Mode), MEMS, strain gage and other types of sensors. All of these products provide conditioning of sensor signals for transmission to data acquisition systems.
-
product
Portable JTAG Boundary-Scan Controller with USB (1.1 and 2.0 High Speed), Ethernet & Firewire Interfaces
JT 37x7/TSI
High speed and performance portable JTAG Boundary-scan controller, containing three interfaces to the test system: USB (1.1 and 2.0 high speed), Ethernet and FirewireThe controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditio...show more -
product
Thermocouple Interface Amplifiers
Analog Devices offers specialized precision thermocouple interface amplifiers that provide a simple and effective solution for measuring thermocouple temperatures. With features such as integrated cold junction compensation and a high gain precision instrumentation amplifier, these thermocouple amplifiers provide a complete signal conditioning system in one IC package. ADI’s thermocouple amplifiers are suitable for use in diverse environments to measure a wide range of temperatures. These products will save you in cost, space, and unnecessary circuit design across a broad range of applications and industries.
