Signal
detectable impulse of electromagnetic radiation or quantum state superposed.
See Also: Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners, Fidelity, Hunting
-
product
PXI 5A Fault Insertion Switch 5-Channel
40-196-101
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each ...show more -
product
Scanner Probe
RFS set
The RFS set consits of three passive near field probes designed for the use in a measurement scanner during the development of E-field and magnetic field. They are designed for frequency ranges of 30 MHz to 3 GHz. The probe heads of the RFS set allow for close measurements needed to correctly localize interference sources on an electronic assembly. They document the whole image of the device under test`s near field. The scanner probes have a sheath current attenuation and are electrically shield...show more -
product
PCI High Density Screened MUX 99 Ch 1 Pole
50-670-021-S-99/1
The 50-670 series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781339-03
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WC...show more -
product
NI TB-2640B Terminal Block for NI 2532B as 1-Wire 4x128 Matrix Topology Without Column Protection Resistors
782385-01
Screw Terminal, Ribbon, 4x128, 1-Wire PXI Module Matrix Terminal Block - The TB-2640B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 4x128 matrix. You can directly connect the TB-2640B to the front panel I/O connectors … of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2640B also provides optional isolation resistors to protect the reed relays from capacitive loads.This 782385-01 card does NOT have 100 Ohm protection.
-
product
950~2400MHz DVB-S 4 ways SAT-IF DWDM Optical Transmitter & Receiver
HDBS-4000DW
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HDBS-4000DW series, combine 4 pieces C-Band, 100GHz, ITU standard wavelength SAT-If optical transmitter, or optical receiver to one chassis, through DWDM, Make 4 ways optical MUX (TX) or DEMUX (RX), through one fiber, used in transmitting 4 ways different polarization SAT-IF signal of one satellite VL, VH, HL, HH with high performance. Installation flexibility.
-
product
PXI Multiplexer Single 48 Ch 1 Pole
40-632-021-48/1
This series of general purpose multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 68-pin connector. Available reed relay formats are 1-pole, 2-pole and 1-pole screened.
-
product
Half Shaft Torque Measurement Systems
Advanced Telemetrics International
ATi’s Half Shaft Telemetry System transmits torque signals from rotating shafts to a stationary telemetry receiver. It connects directly to strain gages adhered to the shaft converting it into a torque sensor allowing it to transmit shaft torque while the vehicle is operating. This system is a testing tool used by automotive and racing engineers to obtain real-time torque measurements from vehicle drivelines.
-
product
Frequency Calibrator
VCH-313
The frequency calibrator VCH-313 is designed to determine the frequency error and calibrate frequency standards of various types based on the signals of the NSC SNS GLONASS/GPS .
-
product
General Purpose Pressure Transducer and Transmitter
P55
The robust P55 pressure transducer provides cost-effective reliability for severe test environments. With extreme resistance to shock and vibration, the P55 pressure transducer delivers the same high-level performance expected from more delicate differential pressure transducers and pressure transmitters. With variable reluctance sensing technology, the P55 pressure transducer delivers fast dynamic response, high resistance to vibration and superior signal stability through ambient temperature c...show more -
product
Transformer Testers
*Quickly tests deenergized power distribution transformers*Briefly energizes the transformer and takes a snapshot of the condition by measuring the voltage, current and power factor of the test signal*Tests overhead, pad-mount and distribution transformers*Audible alarm confirms successful test*Improve SAIDI statistics by quickly testing and getting the transformer back in service*Auto self-test performed with every test*Compact, lightweight and easy-to-use
-
product
Circbord
8022
VECTOR Electronics and Technology, Inc.
Single sided board, circuit pattern one side only, holes not plated thru.Ideal for common busses, signal line running longer distances, for hard wire of test circuits or discrete components. Tracks run close to board edges.
-
product
Digital Panel Meters
Digital panel meters offer high performance and low cost in various packages. Digital panel meters are to display input signals in a variety of electronics applications. They have high resolution displays that are easy to read and backlight version also available for improving visibility.
-
product
Single 4 Ch Fiber Optic MUX SC/PC
40-810-214
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or mult- mode fiber.A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
product
Switch Path Manager Signal Routing Software
Our signal routing software, Switch Path Manager (SPM), simplifies signal routing through switching systems and speeds up the development of switching system software. Switch Path Manager supports our switching modules and the interconnection between them. Once a switching system model has been created, simply defining the endpoints that are required to be connected together can perform signal routing.
-
product
Load Cell Simulator
LCS-3
Load cell simulator particularly useful in a test environment for example to check a program sequence of a controller. The LCS-3 is a simulator used as a substitute for strain gage transducers to generate the precise mV/V signals required in the development , checkout and pre-calibration of signal conditioners, digital and analog readouts and data loggers.
-
product
PCIe-7842, Virtex-5 LX50 FPGA, 200 kS/s Multifunction Reconfigurable I/O Device
781101-01
Virtex-5 LX50 FPGA, 200 kS/s Multifunction Reconfigurable I/O Device - The PCIe‑7842 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe...show more -
-
product
Multi-Conductor Cables
16 Channel, multi-conductor cables are shielded and wired for PCB® equipment specifically. Shielding minimizes noise when located near other power or signal cables. Custom versions are also available on request. Instrumentation-grade BNC / DB-50 connectors are provided to interface with Patch Panels and Signal Conditioners.
-
product
PXI Microwave Multiplexer, Single SP4T, 26.5GHz, 50Ω, SMA, Terminated
40-785C-431-T
The 40-785C-431-T (PXI) and 42-785C-431-T (PXIe) are single SP4T 26.5GHz microwave multiplexers with automatic termination of unused signals. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
product
PXI-5670 , 2.7 GHz RF Vector Signal Generators
778768-04
2.7 GHz PXI Vector Signal Generator—The PXI‑5670 has the power and flexibility you need for product development applications from design through manufacturing. It can generate custom and standard modulation formats such as AM, FM, PM, ASK, FSK, PSK, MSK, and QAM. The PXI‑5670 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as for emerging areas including software defined radio, radio frequency identification (RFID), and wireless sensor networks.
-
product
PXI Dual 4 to 1 RF MUX MCX 75 Ohm
40-832-102
The 40-832-102 is a 75 Ohm 4 to 1 RF MUX with 2 banks in a single PXI slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40-832 minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
product
PXIe-5111, 350 MHz, 3 GS/s, 8-Bit PXI Oscilloscope
785769-01
PXIe, 350 MHz, 3 GS/s, 8-Bit PXI Oscilloscope—The PXIe-5111 oscilloscope has two channels that sample up to 3 GS/s with flexible and programmable settings for coupling, input impedance, voltage range, and filtering. PXI Oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that facilitates high-speed data throughput and includes analysis functions. This device is ideal for automated and partially automated applications that require flexible measur...show more -
product
LXI Microwave Multiplexer, SP6T, 5-Bank, 26.5GHz, 50Ω, SMA
60-800-305
Our 60-800-305 is a 5 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
Single Channel USB Programmable High-Pass Filter
USBPHP-S1
The USBPHP-S1 stand alone USB controllable module provides a single channel of high pass filtering and high-quality instrumentation amplifier for front-end signal conditioning compatible with all popular A/D converter devices. The USBPHP-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPHP-S1 will remember all of the program...show more -
product
LXI Microwave Multiplexer, 50Ω 4-Channel 6-Bank 40GHz SMA-2.9
60-802-406
The 60-802-406 is a 4-channel, 6-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
SMB Female to SMB Female Cable, 50 Ohm, 30 cm
763390-01
The SMB-SMB Coaxial Cable, sometimes referred to as SMB-200, connects measurement and signal devices. NI offers this 50 Ω cable in different lengths.
-
product
PXI/PXIe RF Multiplexer, Dual 4-Channel, Terminated Common, 3GHz, 50Ω, SMB
40-876A-002
The 40-876A-002 (PXI) and 42-876A-002 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 2 banks in a single slot. Additionally, extra switching allows the common connection to be terminated into 50 Ohm, maintaining signal integrity. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
product
USB-5132, 50 MHz Bandwidth, 2-Channel, 8-Bit USB Oscilloscope Device
779969-02
50 MHz Bandwidth, 2-Channel, 8-Bit USB Oscilloscope Device - The USB‑5132 low-cost oscilloscope device has two channels that sample up to 50 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes and an instrument driver that includes data streaming and analysis functions. This device is ideal for portable and benchtop applications with fast signals that require flexible measurement configurations and up to 50 MHz of analog bandwidth.
-
product
Power Meters
Rk-5700
The Rk-5700 Series Power Meters accept a wide variety of probes – pyroelectric, silicon, and thermopile – enabling them to perform absolute radiometry, total laser power (cw and average), and irradiance measurements from the UV to far-IR, pW to kW. Integrated lock-in amplifier circuitry allows for synchronous detection of chopped optical signals, improving both S/N ratio and background rejection. The dual channel Rk-5720 simultaneously measures Channel A, Channel B, and the ratio B/A. An IEEE-488 GPIB computer interface, Analog Outputs, Background Cancel, and Autorange are all standard features.
