Showing results: 3541 - 3555 of 8180 items found.
-
Techimp HQ S.r.L
Techimp Voltage Tap Adapter is gender changer which allows the user to connect to the test tap (sometimes called power factor tap) of high voltage transformer bushings.While keeping the test tap well below the safety voltage level required by the manufacturer, the Tap Adapter lets the user to drain high frequency PD signals for diagnostic assessment of insulating materials.A synchronization signal can be derived as well.It is suitable for both single shot as well as continuous PD monitoring.Although it must be customized on the basis of the shape and dimension of the test tap (to be provided by the Customer), many models are readily available for the most established transformer bushings. A list of the presently available models is reported below.Several thousands of hours of operation are a guarantee of reliability and accurate design.
-
C Series -
NI
C Series Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑Rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Talon RTR 2750 -
Pentek, Inc.
- Sixteen 250 MHz 16-bit A/Ds- Sixteen independently-configurable DDC decimations ranging from 2 to 65536- Sixteen independently-configurable DDC tuning frequencies- Capable of recording RF frequencies to 700 MHz- Capable of recording signals with bandwidths to 100 MHz- 8 GB/s real-time aggregate recording rate- 4U 19-inch rugged rackmount PC server chassis- Windows® 7 Professional workstation with high performance Intel® Core™ i7 processor- Front panel removable-SSD drives- Up to 61 terabytes of storage to NTFS RAID disk array- Multiple RAID levels of 0, 1, 5 and 6- SystemFlow® GUI with signal viewer analysis tool- Optional GPS time and position stamping
-
E-CAM55_CUMI0521_MOD -
e-con Systems Inc.
e-CAM55_CUMI0521_MOD is a small form factor, 5 MP fixed focus camera module based on AR0521 CMOS image sensor from ON Semiconductor® has a dedicated, high-performance Image Signal Processor chip (ISP) on-board that performs all the Auto functions (Auto White Balance, Auto Exposure control) in addition to complete image signal processing pipeline that provides best-in-class images and video. This low light camera module can stream uncompressed VGA (640 x 480) at 75 fps, HD (1280 x 720) at 100 fps, 1280 x 960 at 75 fps, FHD (1920 x 1080) at 65 fps, 2560 x 1440 at 38fps, 2592 x 1944 at 28 fps.
-
40-666-011 -
Pickering Interfaces Ltd.
The 40-666 is a high current multiplexer available in dual 3-channel or single 6-channel configurations occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive. Note: The 40-666-011 supersedes the 40-666-001 which is functionally the same but with some changes in specification. A data sheet for the 40-666-001 can be found in the40-666/667 User Manual.
-
40-667-011 -
Pickering Interfaces Ltd.
The 40-667 is a high current multiplexer available in dual 3-channel or single 6-channel configurations occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.Each multiplexer channel can support 30A of continuous current and switch up to 40V signals. The switches can sustain inrush currents in excess of 120A. AC or DC signals can be switched since the switch is polarity insensitive.Note: The 40-666-011 supersedes the 40-666-001 which is functionally the same but with some changes in specification. A data sheet for the 40-666-001 can be found in the 40-666/667 User Manual.
-
JT 2149/MPV eMPV -
JTAG Technologies Inc.
The JT 2149/MPV and the JT 2149/eMPV are a 32 channel multi purpose DIOS/TAP pod modules/interfaces that can be plugged into any spare JT 2148 QuadPOD transceiver slot. The DIOS channels of these units I/O interface pods enable increased fault coverage and thus improved diagnostic resolution during boundary-scan testing. The principal difference between the two versions is the use of an extended case on the eMPV that allows standard 0.1″ connections to be used to access ths TAP and static IO signals (see tab below)- on the standard /MPV unit these signals are available at the front face 0.05″ connector. The units are fully supported by JTAG Technologies’ development tools. Additional DIOS modules can be serially connected if more parallel access points are required.
-
TFG5200 Series -
Twintex Electronics Co., Ltd
The TFG5200 series are arbitrary waveform/function generators with maximum frequency of 25MHz, 40MHz and 60MHz, based on Direct Digital Synthesis (DDS) technology, providing high fidelity, low jitter performance function signal and arbitrary waveform signal.
-
IQRX -
Quantifi Photonics Inc.
The IQRX is a “gold standard” coherent receiver for the measurement of coherent modulation formats such as QPSK, 64QAM and OFDM.Its high-bandwidth, low-noise architecture makes it ideal for high-quality, low-distortion coherent signal measurement.With two built-in lasers and convenient touchscreen LCD front panel control, the IQRX delivers quick and reliable measurements.
-
alpha300 access -
WITec
access is a micro-Raman single-spot analysis and mapping microscope. It was specifically engineered for budget-conscious customers with high demands on instrument performance. Its outstanding spectral quality, optical throughput and signal sensitivity are ensured by well-established WITec optical elements. The high-quality microscope setup of the access is also the basis for its full upgradability.
-
Z-Gard DS Sensor -
MSA
The Z-Gard DS Sensor is designed to detect the presence of carbon monoxide and nitrogen dioxide gases in parking garages, vehicle storage areas or wherever else these two toxic gases could be found. These sensors employ electrochemical sensors which generate a representative output signal proportional to the calibrated operating range.
-
ST-C6HD-HDBT -
Network Technologies Inc
The XTENDEX® HDMI HDBase-T Extender transmits uncompressed digital HDMI signal and IR up to 328 feet over a single CAT5e/6/7 cable using HDBase-T technology. Each video extender consists of a local unit that connects to an HDMI source and a remote unit that connects to an HDMI display.
-
VCH-604 -
VREMYA-CH JS Company
High-Frequency Switch VCH-604 is designed for switching high-frequency (1 – 100 MHz) and pulse TTL signals. VCH-604 contains two groups of channels; each group has 25 inputs and 2 outputs. VCH-604 can be controlled from PC via GPIB and RS-232 interfaces or directly from front panel.
-
PCIe Synchro -
Computer Conversions Corporation
Our versatile PCIe platform enables the mounting of various combinations of input and output modules. We offer resolutions from 10 to 16 bit and various input and output signal configurations. It is possible to achieve up to 8 input channels or combine input and output modules to suit unique applications.
-
60-800-012 -
Pickering Interfaces Ltd.
Our 60-800 Microwave Multiplexer range is suitable for switching 50 ohm signals up to 26.5GHz. With the capability of supporting up to 16 banks of 6 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA connectors.
