Sensor Testers
-
product
Sensor Tester
QST-5
The QST-5 device is intended for testing many popular sensors used in the automotive industry. The tester powers the tested sensors by itself, so it can be used both in a vehicle and outside of it.
-
product
Measurement, Communications & Testing
Process & Analytical Instruments division of AMETEK
Measurement Communications & Testing provides the design, integration and installation of critical communication systems, workflow, life-safety solutions and calibration instruments for temperature, pressure and process control. It also is a leader in level measurement devices, continuous position sensors, hardness testers, force measurement devices and retractable cord reels. In addition, it offers a line of weathering test instrumentation along with laboratory and outdoor testing services.
-
product
Oxygen Sensor Tester and Simulator
ST05
The sensor signal output is shown in real time on the bar graph, while a 2 digit alphanumeric display shows the sensor output cross count per second. By pressing the ?Test? button and performing a snap throttle acceleration of the engine, it tests the response time of the sensor and shows a pass or fail result within seconds. Two buttons allows for simulation of rich or lean conditions to monitor response of the engine control module.
-
product
Portable RF Analyzer
PMT-330
The Process Sensors Portable Moisture Tester (PMT-330) puts the capabilities of an on-line moisture analysis and control system into the palm of your hand, allowing operators to spot-check moisture content of boards, wood, plastic, and paper products quickly and easily. It features radio frequency dielectric (RF) measurement technology that penetrates the surface of products and instantly displays accurate moisture data.
-
product
ADB Bearing Sensor Tester
The ADB Sensor Tester (ADBT) has been designed to test 4B adjustable depth bearing (ADB) style temperature sensors in the field. During planned maintenance or periodic testing, the ADBT can be used as a diagnostic tool to verify the alarm and shutdown sequences of the control unit are functioning as expected. The unit operates in two testing modes, direct (heated) and indirect (simulated).
-
product
Image Sensor Test System
IP750
Teradyne's IP750 series dominates the image sensor tester market with its superior performance and low cost of test. The IP750 delivers high throughput and high parallel test efficiency, broad device test coverage from CCD and CIS, analog and digital capture, and concurrent image sensor and logic testing. In addition, Teradyne's IG-XL software environment provides easy, shorter test program development and easy maintenance.
-
product
Measurement & Diagnostic Products
DURST Motor & Electric Industries Pty Ltd.
DURST Measurement & Diagnostic Products; circuit tester, vehicle battery analyzer, multimeter, dedicated automotive multimeter, clamp meter, sound level meter, oxygen sensor tester, diesel engine tachometer, multisystem ignition analyzer, faultfinder, circuit tester, diode tester, regulator tester, growler for testing motor insulation, armature/commutator tester, diagnostic testers, current clamps, optical photo/contact tachometer, etc.
-
product
Oxygen Sensor Tester And Simulator
7650
Peaceful Thriving Enterprise Co Ltd
This device is designed to test and to simulate 1V Zirconia and 1V/5V Titania type oxygen sensors. The simulation can help user to exam the function of the ECU. Moreover, it can analyze the type of connection wire.
-
product
AMIDA 2020XP Tester
AMIDA 2020XP CIS tester is the latest generation of CMOS image sensor-specific measuring instruments from Metatech. In addition to the original true and accurate measurement, the high-throughput mass production solution designed for the high-throughput inspection of image lens modules and camera lenses has been well received after nearly 20 years of mass production experience. First-class factories at home and abroad import production. AMIDA 2020XP CIS testing machine not only meets the customer's testing time and high output and accuracy requirements. Within the range of functional flexibility, users can customize their measurement requirements according to the definition of various sensors. AMIDA 2020XP CIS tester is a new generation of CMOS Image Sensor dedicated tester, which integrates DC open/short/leakage test, AC Pattern test and image test. It uses 180 Pin high-speed cable to connect to the test end
-
product
Sensor Tester
*Connection facilities for DC 2-wire and 3-wire sensors, *Change in switching status signalled visually and acoustically, * 15 V operating voltage for sensors when using a 9 V block battery, * Switches off automatically when not in use, * Visual indicator for operating voltage, switching status and low battery
-
product
Image Sensor/Fingerprint-on-Display Testing
Enli Tech provides the most advanced optical and non-destructive inspection technology, which can de-convolute the digital images back to the analog properties, such as quantum efficiency, spectral response, system gain K, Dynamic Range (DR), PRNU, DRNU, Linearity Error LE, and Chief-Ray-Angle (CRA). The testing solution can be applied to CCD and CMOS image sensors in aerospace, defense, and scientific camera field. Image sensor packages that can be tested by Enli Tech’s systems include bare wafers, dies, chips, or camera modules. Our image sensor testers can help users reduce the sensor-modules or camera-modules development time and RD budget.
-
product
MXE EMI Test Receiver, 3 Hz to 44 GHz
N9038B
The Keysight N9038B is a standards-compliant MXE EMI test receiver and diagnostic signal analyzer built on an upgradeable platform. You choose the frequency coverage you need to fully test devices with outstanding accuracy and sensitivity across required ranges.
-
product
KVS Rugged Igniter Tester With Current Monitor
4314
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
product
S2 Penta Sensors
ULP-S2 PCI/V
Optomistic Products’ best-selling Sensor, the ULP S2 Penta Sensor, is relied upon for its versatility in accommodating most LED color and intensity test applications. Implemented in a unique and customizable 2-Part solution, the S2 Penta Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption:Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsOutput Loads: ‘Int.’& ‘Color’- 2Kohms min., 100pF max.Output Pins: 4 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longTypical response times: Typical response time: <10mS capture time; <100mS overall responsetime for color and intensity simultaneouslyFiber-Optic Probes: Can be paired with any Universal LightProbe Fiber-Optic Probe
-
product
S2 Unicolor Digital Sensors
ULP-S2 SCC
The Universal LightProbe S2 Unicolor Digital Sensor is pre-programmed to respond only to a specific color LED, including blue, green, yellow, orange, red, plus white. The Universal LightProbe S2 Unicolor Digital Sensor is designed for the simple ON/OFF test and color check of a single color LED, with a digital output, quickly determining PASS/FAIL status without further processing by Automatic Test Equipment. The Universal LightProbe S2 Unicolor Digital sensor provides the simplest and fastest interface to Automatic Test Equipment (ATE).Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts, at 6mA max.; less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times: <10mS capture time; <65mS overall response timeFiber-Optic Probes: Can utilize any Universal LightProbe Fiber-Optic Probe
-
product
Waveguide Power Sensor
Q8486D
Excellent SWR for reducing mismatch uncertainty50 MHz calibration port Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter Accurate average power measurements over -70 to -20 dBm Frequency range 33 GHz to 50 GHz Diode power sensing element
-
product
S2 Unicolor Sensors
ULP-S2 SCI/V
The Universal LightProbe S2 Unicolor Sensor is designed for the intensity test of any single one of the five main LED colors (blue, green, yellow, orange, and red) plus white and Infrared (700nm to 1,000nm). Implemented in a unique and customizable 2-Part solution, the S2 Unicolor Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times:<10mS capture time; 65mS overall response time; intensity output of correct color only.Fiber-Optic Probes: Can utilize any Universal LightProbe Fiber-Optic Probe
-
product
Bit Error Rate Tester - MATRIQ
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
10 MHz to 40 GHz LAN Wide Dynamic Range Average Power Sensor
L2054XA
The Keysight L2054XA is a fast, accurate and wide dynamic range 10 MHz – 40 GHz LAN average power sensor.
-
product
Waveguide Power Sensor
E8486A
Keysight waveguide power sensors are fully compatible with Keysight EPM (E4418B/19B, N1913A/14A), EPM-P (E4416A/17A) and P-Series (N1911A/12A) power meters. The V8486A and W8486A are also compatible with the discontinued or obsolete power meters such as 435B, 436A, 437B, 438A, 70100A, E1416A, E4418A, and E4419A power meters.
-
product
10 MHz to 33 GHz USB Wide Dynamic Range Average Power Sensor
U2053XA
Your product description goes here.The Keysight U2053XA is a fast, accurate and wide dynamic range 10 MHz – 33 GHz USB average power sensor.
-
product
Digital Power Meter
66203/66204
Chroma 66203/66204 Power Meters are designed for multiple phase power measurement applications. The wiring mode function allows the user to take accurate power measurements for various wiring modes 1P2W/1P3W/3P3W/3P4W as well as providing accurate standard power measurements common for most electrical devices. A unique feature of the 66203/66204 is its stateof- the-art DSP digitizing technology instead of less accurate and slower traditional analog circuits. The internal 16 bits analog/digital converters with sampling rates of up to 250kHz provide both high speed and high accuracy measurements which is unprecedented within the industry for this class of power meters. The instruments include a four part display with 7-segment LED front panel readouts. Users can easily select desired parameters and readouts with a touch of a button. The 66203/66204 meters also include remote control using USB or GPIB interfaces via rear panel connections.
-
product
Thermocouple Power Sensors
N8488A
N8488A power sensor has the widest frequency range among N8480 power sensors offering from Keysight.
-
product
DC/10 MHz 50 GHz USB Thermocouple Power Sensor
U8487A
The U8480 series is Keysight's first power sensor with the capability to measure down to DC (only applicable for U8481A/85A). Now, with an expanded frequency range up to 50 and 67 GHz, the U8480 series allows you to make fast and accurate high frequency power measurements in applications ranging from PNA/MXG calibration to high volume manufacturing.
-
product
10 MHz – 6 GHz USB Power Sensor
U2001B
U2001B USB power sensor measures average power over the frequency range 10 MHz to 6 GHz and power range -30 dBm to +44 dBm.
-
product
18-Channel LED Analyzer
AL568
The format of the AL568 optical fiber for LED test is the most convenient and effective system on the market. It sits in the space of a 90 Series VPC module and only requires connection to a USB port to get data from up to 18 LEDs.
-
product
Power Sensor and SNS Noise Source Cable (1.5m / 5 feet)
11730A
The Keysight 11730 series power sensor cables are used with the 8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements.
-
product
Optical Contact POF Ext Ø 1mm For VPC RCV Mini Power 510104123
AN396
Optical contact probe for sensing LEDs.
-
product
E-Series Peak And Average Power Sensor, 50 MHz To 18 GHz
E9327A
The E9327A power sensor has a 5-MHz video bandwidth and is ideal for time-gated peak, average, and peak-to-average ratio power measurements on W-CDMA wireless formats such as cdma2000.
-
product
10 MHz to 6 GHz USB Wide Dynamic Range Average Power Sensor
U2051XA
The Keysight U2051XA is a fast, accurate and wide dynamic range 10 MHz – 6 GHz USB average power sensor.
