Showing results: 391 - 405 of 466 items found.
-
EMC Partner AG
Screw connections on top of the generator, enable easy connection to the EUT. The MIG0603 is the ideal voltage insulation tester with a broad application range. The MIG "Modular-Impulse-Generator" is a flexible kit system, ready to quote tailored generators for special test applications. The MIG is a further innovative solution of EMC PARTNER AG to cover customers requests. The basic units are discharge modules (patent pending) which can be configured in serial or parallel, to offer an optimum solution for the customer need. The use of one type of discharge module guarantees a high reliability and a high qualit . Requires TC-MIG24 or CN-MIG24.
-
785479-01 -
NI
Non-Enclosed, ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO‑9222 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The sbRIO‑9222 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the sbRIO‑9222: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
782385-01 -
NI
Screw Terminal, Ribbon, 4x128, 1-Wire PXI Module Matrix Terminal Block - The TB-2640B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 4x128 matrix. You can directly connect the TB-2640B to the front panel I/O connectors … of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2640B also provides optional isolation resistors to protect the reed relays from capacitive loads.This 782385-01 card does NOT have 100 Ohm protection.
-
LCD20 -
Mantracourt Electronics Ltd
Our intelligent strain gauge bridge amplifier is a compact, stackable microprocessor based unit specifically designed to control and monitor process applications. Flexible connection to most load cells, pressure or strain gauges over a wide range of sensitivities. The unit provides isolated current 4-20mA and voltage 0-10V analogue outputs and two digital inputs. Two set point relays can be configured to set thresholds such as net, gross, peak and valley. Powered from a wide ranging DC supply, the DIN rail amplifier is supplied with 2 part screw connectors for ease of installation.
-
ZOLIX
Model: KSAV Ultra-High Precision Motorized Vertical StagesKSAV1010/2030-ZF is new product, wedge vertical stage with.high-resolution, so many advantages: high-stability, high-load and capacity in vertical position,self-locking.applicatin filed: high postion precision,high load capacity,limited space and so onCharacteristic ◆Cross ball screw rail,precion ground ensure resolution, straightness,high load capacity, limited space◆small travel improve resolution◆stepper motor and DB9 interface, choose controller flexibility◆switches ensure safe when operate◆ planning other specification and size
-
Teledyne e2v
Teledyne e2v has developed compact MIPI modules which feature our own high performance CMOS image sensors inside a pre-focused, industrial-grade scanning optic. As a turnkey sensor/optics for imaging systems, these modules offers customers significant reduction in development time and cost savings. Only a few screws are needed to mount the module, with simple connection to the image processing system through an FPC cable connector. Software development efforts can also be reduced by using some limited API-layer Linux software drivers. This enables the module to be seamlessly interfaced to popular ISP platforms.
-
SparkFun Electronics
The SparkFun Qwiic Quad Relay is a unique power accessory board that has been designed for switching not one but four high powered devices from your Arduino or another low powered microcontroller using I2C. Taking a look at the board, the Quad Relay has four individual relays rated up to 5 Amps per channel at 250VAC or 30VDC. Each channel also has its own uniquely colored LED, silk for easy identification, and screw terminals for optional connection. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system!
-
Bloomy Controls, Inc.
Bloomy’s Multipurpose Module for SLSC provides a convenient location in an SLSC system for applications ranging from a simple rearrangement of signals to installation of circuits and components. Both front panel connectors are mapped to screw terminals, through holes, and surface-mount technology pads thus accommodating a wide variety of components. Breakout areas for all rear transition interface (RTI) pins simplify integration into SLSC-based systems. On-board power supplies (±15VDC, +5V, and +3.3V) are also made available for the user’s analog and digital circuits. The module features a considerable amount of available board space for user applications.
-
782536-01 -
NI
68-Pin Female Screw Terminal to 68-Pin Female D-SUB, DIN-Rail, Shielded I/O Connector Terminal Block - The SCB-68A provides a shielded I/O connection for interfacing I/O signals to plug-in data acquisition devices with 68-pin connectors. This Terminal Block combines with shield cables to provide low-noise signal termination. The SCB-68A incorporates a completely redesigned mechanical enclosure with a magnetic removable lid, DIN-rail mount compatibility, and a resettable fuse. It is compatible with single- and dual-connector Multifunction I/O with 68-pin connectors. The SCB-68A also includes two general-purpose breadboard areas and an onboard cold-junction compensation sensor.
-
Model 8021NX -
Telebyte, Inc.
FEATURES: Fast Response; Automatic Recovery; Up To 20 MBPS Data Rate; DIN Rail Mounted; Triple Stage Protection; Two Wire. The Model 8021NX is a DIN Rail mounted surge suppressor for 2-wire RS-485 circuits used to protect factory data networks, or, any RS-485 network that wants to avail itself of the DIN Rail packaging concept. The Model 8021NX provides common-mode (line to ground) surge protection and differential mode (line to line) protection for balanced networks. All the inputs, outputs and ground connections are via screw terminals located on the top surface of the device.
-
Model 8022NX -
Telebyte, Inc.
FEATURES: Fast Response; Automatic Recovery; Up To 20 MBPS Data Rate; DIN Rail Mounted; Full Duplex; Triple Stage Protection. The Model 8022NX is a DIN Rail mounted surge suppressor for 4-wire RS-422 or RS-485 circuits used to protect factory data networks, or, any network that wants to avail itself of the DIN Rail packaging concept. The Model 8022NX provides common-mode (line to ground) surge protection and differential mode (line to line) protection for balanced networks. All the inputs, outputs and ground connections are via screw terminals located on the top surface of the device.
-
WIKA Alexander Wiegand SE & Co. KG
When the compression force transducer has a through hole, it is called a ring force transducer (donut load cell) or a force measuring ring. These force transducers are extremely robust and are suitable for the detection of very high (static) forces. Furthermore, they are suitable for many installation situations. The ring geometry is used in force measurement for a wide variety of spatial conditions. The main fields of application are found in spindle presses, in screw force measurement or even in geotechnology. WIKA offers electrical and hydraulic ring force transducers in diameters from 12 millimetres up to 430 millimetres as well as in various installation heights. Discover our portfolio now.
-
Shimadzu Corp.
Shimadzu’s SSG series of strain gauge extensometers are compliant with ISO, JIS, and ASTM tensile test standards, including those for plastics and metallic materials These lightweight, precision extensometers feature a wide elongation measurement range, while retaining the flexibility to measure using small gauge lengths, and support both rod and flat plate shaped specimens. Consisting of an elongation sensor and amplifier, this extensometer is suitable for use with metals and hard plastic materials, and is fastened securely to specimens with screws. Calibration using an extensometer calibrator allows the extensometer to meet JIS and ISO Class 0.5 and ASTM Class C standards for higher accuracy.
-
Additel Corporation
Pressure Test Pump is a hand operated pressure pump designed to generate pressure from 95% vacuum to 1,500psi (100bar). A high-quality screw press is designed for fine pressure adjustment, with an adjustment resolution up to 10 Pa (0.1 mbar). A specially designed shut-off valve makes the pressure as stable as possible during calibration. A built-in gas-liquid isolator protects the pump from moisture and dirt to reduce the need for maintenance. Two hand-tight quick connectors installed on the pump allow easy connecting and disconnecting to the test pump without the need for PTFE tape or wrenches. The 918 is an ideal comparison test pump for pressure instruments calibration.
-
MODEL DPM-2 -
Transducer Techniques, Inc
The voltage-to-frequency microprocessor makes Transducer Technique's 4-digit panel mount meters the ideal solution for meeting the measurement, display and control requirements of noisy industrial applications, OEMs and system designers. Model DPM-2 accepts any full bridge transducer. Balance and span can be selected via the front keypad, thus allowing the display to read directly in engineering units. Front panel max and tare functions are ideal for industrial weighing applications. Isolated adjustable 9-11 VDC excitation with remote sense and 90 mA drive eliminates the need for external power supplies. Rear screw terminals connectors are included.
