Showing results: 151 - 165 of 466 items found.
-
ThermoVault -
MadgeTech, Inc
Oven Temperature Profiling kit. Comes with TC101A Thermocouple based Temperature Data Logger with screw terminal, Thermally insulated enclosure, and Type K thermocouple probe.
-
IQ Series -
Ametek Land
IQ series thermometers feature an all metal design with integrated water cooling, air purge and screw terminal connections to facilitate simple and cost effective operation.
-
Virginia Panel Corporation
modules mount from the rear of the iCon receiver and ITA and allow installation and removal of pre-wired cable blocks. The modules also have captive Phillips head screws.
-
Metra Mess- und Frequenztechnik in Radebeul e.K.
Triaxial accelerometers are intended for simultaneous measurement of vibration in 3 perpendicular axis. All models have a central drilling for easy screw attachment and convenient axis alignment.
-
Virginia Panel Corporation
Modules mount from the rear of the iCon receiver and ITA and allow installation and removal of pre-wired cable blocks. The modules also have captive Phillips head screws.
-
-
Traceable Products
Meter reads from 0 to 1,999 foot-candles (resolution 0.1 to 1). Bright 1/2-inch-high digits make it an easy to read pocket light meter. The simplicity of the two-button operation eliminates the need to refer to directions. Functions are on/off, and range. The meter can be zeroed with the simple turn of an adjustment screw
-
510161109 -
Virginia Panel Corporation
iCon modules mount from the rear of the iCon receiver and ITA and allow installation and removal of pre-wired cable blocks. The modules also have captive Phillips head screws.
-
cBP-6418U -
ADLINK Technology Inc.
*1 Segment: 1 system + 7 peripheral slots*cPCI BUS: up to 64-bit/66MHz*Power connectors: ATX connector x 1 DC Screw terminals
-
510161108 -
Virginia Panel Corporation
iCon modules mount from the rear of the iCon receiver and ITA and allow installation and removal of pre-wired cable blocks. These modules also have captive Phillips head screws.
-
779353-01 -
NI
37-Pin, Female D-SUB to 40-Pin, Female Screw Terminal, Desktop Mount Terminal Block - The CB-37F-LP is an unshielded terminal block that provides access to DAQ devices with 37-pin connectors. The 37-pin, D-SUB connector makes this connector block ideal for direct mounting on the … DAQ device or connecting through a cable.
-
199SM / 198EM Magnet Wheels -
Electro-Sensors, Inc.
Magnet wheels work with Electro-Sensors Hall Effect shaft speed sensors providing 120 alternating magnetic poles around the circumference of the 3.75" diameter. The 199SM models mount around shafts up to 3" in diameter and are secured with set screws (provided). The 198EM mounts on the end of a shaft with a 10-32 UNF screw (provided - requires center drilling and tapping the shaft).• Use with 906, 906B, 1101 and other Hall Effect, non-metallic-end-capped shaft speed sensors (consult factory)
-
92-965-200-M -
Pickering Interfaces Ltd.
Suitable for use on the front of PXI modules this connector block provides a simple method of connecting to high density 200-Pin LFH connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximize copper cross sectional area and insulation properties. Users should make their own cable strain relief arrangements and ensure that appropriate electrical safety precautions are observed.
-
DIW-120/75/20/15 -
Sugisaki Meter Co., Ltd.
Tightening of screws and bolts and final check. The wrench head part rotates about 300 degrees! The line of sight and the display panel are always parallel, improving operability. Lightweight and compact with an integrated display! Cordless for even better operability. Stable measurement can be performed even during long hours of work. A screw tightening counter function is also included as standard. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change.
-
DIS-RL series (05/2/6) -
Sugisaki Meter Co., Ltd.
Tightening and final check of screws and bolts. Separate type digital torque driver/wrench. The detection part is very compact, and it is effective for torque measurement in narrow places and minute torque measurement. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change.