Screw
See Also: Thread, Linear Actuators
-
Product
Cold Bend Testing Machine
QualiBend Series
-
The Cold Bend Testing Machine - QualiBend series are used for bending of metallic materials such as metal rods, planks and steel screw threads. The machines operate with a hydraulic loading system to adjust the distance of the cold-bending press roll to drive the rod in both directions making the cold bending press roll forward and back.
-
Product
- RS-485 DIN Rail Mounted Surge Suppressor
Model 8021NX
-
FEATURES: Fast Response; Automatic Recovery; Up To 20 MBPS Data Rate; DIN Rail Mounted; Triple Stage Protection; Two Wire. The Model 8021NX is a DIN Rail mounted surge suppressor for 2-wire RS-485 circuits used to protect factory data networks, or, any RS-485 network that wants to avail itself of the DIN Rail packaging concept. The Model 8021NX provides common-mode (line to ground) surge protection and differential mode (line to line) protection for balanced networks. All the inputs, outputs and ground connections are via screw terminals located on the top surface of the device.
-
Product
SH25M-10F Cable, 25-Pin Male D-SUB to 10-Pin Female COMBICON, Shielded Multifunction Cable
190654-02
Multifunction Cable
25-Pin Male D-SUB to 10-Pin Female COMBICON, Shielded Multifunction Cable - The SH25M-10F Cable, sometimes referred to as SH10F-25M, connects C Series DAQ devices with a 10-pin screw terminal to a 25-pin D-SUB. The SH25M-10F Cable is offered in different lengths.
-
Product
34945A Distribution Board, With Generic Screw Terminals For Driving 16 Switch Coils
Y1155A
Distribution Board
The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.
-
Product
96-Pin Male SCSI to 96-Pin Female SCSI Switch Cable, 1m (protected)
150579-01
Switch Cable
96-Pin Male SCSI to 96-Pin Female SCSI Switch Cable, 1m (protected) - The SH96F-96M SwitchBlock SCSI Cable provides connectivity for SwitchBlock modules. You can connect these to the TBX-2809 Terminal Block, which exposes each channel of the switch module to screw terminals.
-
Product
Integrated Potentiostat and Multiplexer
EmStatMUX8
-
Based upon the EmStat range, there are two types of multiplexers to suit most types of sensor array work. The MUX8 is the most flexible offering the ability to connect arrays made of up to eight working electrodes in two or three electrode cell types and chips sharing a reference electrode and/or counter electrode. The MUX16 is suitable for sensor arrays or chips with sixteen working electrodes all sharing a RE and/or a CE. Both instruments are suitable for laminated layer corrosion analysis.The potentiostat is controlled and powered by USB and is used with PSTrace allowing for simultaneous sampling of each channel at a rate of 25 ms/channel. Standard packaging includes a shielded cable with connections for a working, a counter and a reference electrode by means of 2 mm banana connectors and mini-crocodile clips, a stripped end, Dsub-37 terminated flat cable and a USB cable. To make connections to chips simpler the Connection Terminal is an optional extra providing clearly marked screw terminals to the electrodes and can be directly joined to the ESMUX via their D-Sub connectors.
-
Product
96-Pin Female DIN to 67-Pin Female Screw Terminal, 10 V, PXI Module Mount Terminal Block
781349-01
Terminal Block
NI TB-4353 Isothermal Terminal Block for PXIe-4353
-
Product
UL496 Lampholder Torsion Meter
CX-DTN
-
Shenzhen Chuangxin Instruments Co., Ltd.
This Lampholder Torsion Test Device is strictly designed according to UL496 etc. It's mainly used to the screw lampholder torsion test of protecting accidental force.
-
Product
High Temperature Infrared Spot Thermometers
IQ Series
-
IQ series thermometers feature an all metal design with integrated water cooling, air purge and screw terminal connections to facilitate simple and cost effective operation.
-
Product
Ultra HD Surgical Monitor Series
ASM32UHB
Industrial Monitor
The ASM32UHB Series of medically certified UHD surgical monitors features clear image and accurate color reproduction to fully support medical personnel. As a result of its hygienic surface design that eliminates exposed screw heads and air vents, the ASM Series can be easily and quickly cleaned using all common disinfectants and cleaning agents. This ensures a high level of hygiene in pathogen-sensitive environments such as the OR. The ASM Series’ hygienic design also can speed up turnaround time and operating theater preparation.
-
Product
SparkFun MicroMod RP2040 Processor
-
The SparkFun MicroMod Pi RP2040 Processor Board is a low-cost, high-performance board with flexible digital interfaces featuring the Raspberry Pi Foundation's RP2040 microcontroller. With the MicroMod M.2 connector, connecting your MicroMod Pi RP2040 Processor Board is a breeze. Simply match up the key on your processor's beveled edge connector to the key on the M.2 connector and secure it with a screw (included with all Carrier Boards).
-
Product
NI-9223, ±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
781398-01
Voltage Input Module
±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9223 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9223 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9223: either four, 2‑position screw terminal connectors or four BNC connectors.
-
Product
Assembly Systems
-
Easily add automation to your assembly process. Free operator hands and eliminate the need to manually handle screws. The A-50 units are modular...a simple rail change and readjustment are all that are necessary to use a variety of screw sizes.
-
Product
Fence Vibration Sensor
ENVIROMUX-FENCE1
-
Detects when individuals climb over or cut through chain link or wire mesh fences. Advanced built-in signal processor prevents false alarms. Four sensitivity settings to tune each sensor to a particular fence section and intrusion type. Two open-collector outputs – alarm and power failure. UV resistant case and epoxy sealed electronics provides maximum resistance to harsh environments. Rated NEMA 4X and UL94 5V. Use individually or chain units with each ranging from 40 to 60 feet away. Includes mounting brackets for installing the sensor to fence fabric. Screw terminals. Operating temperature: -4 to 131°F (-20 to 55°C). Operating voltage: 9-15V DC.
-
Product
Module Accessory Kit, Quantity 26 2-56 x .375" Flat Head Phillips Screws Stainless Steel
510109369
Accessory Kit
Used with modules: 510104149, 510108281 and 510171101.
-
Product
Keying Pin Kit, Receiver/ITA
310118112
Keying Pin Kit
The Keying Pin kit is a way to avoid damaging the contacts within the ITAs and Receivers. Simply insert the longer keying pins into the receiver and the smaller set screws into the ITA to create the pattern needed to isolate your test fixtures so there is no operational mismatch.
-
Product
Terminal Block For The 34939A 64-Channel Form A Switch
34939T
Terminal Block
This terminal block is used for discrete wiring. A fully loaded terminal blocks supports up to 20 AWG wire size typical and 18 AWG max. This terminal block has screw terminal connections.
-
Product
Lever Handle Bed of Nails Testers
Automator Manual Family
-
Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.
-
Product
TB-2650, Screw Terminal, 8x64, 1-Wire PXI Module Matrix Terminal Block
781131-03
Terminal Block
The TB-2650 provides the necessary routing to configure the PXI-2531 or PXIe-2531 PXI Matrix Switch Module as a 1-wire 8x64 matrix. You can directly connect the TB-2650 to the front panel I/O connectors of the PXI-2531 or PXIe-2531.
-
Product
DIP Header with Coined Contacts
Series 600
-
DIP Headers with Coined Contacts. Aries offers a full line of DIP headers, available with either coined or screw machine contacts. Consult Data Sheet No. 12035 for screw machine contacts. Snap-on, protective covers are available for all sizes shown below and accommodate .125 [3.18] to .750 [9.05] component heights. Consult Data Sheet No. 12033 for protective covers.
-
Product
Cable Assembly, 68 Pin Male Offset VHDCI (Thumb Screws), to 68 Pin Female SCSI (Thumb Screws), 36"
Cable Assembly
Cable Assembly, 68 Pin Male Offset VHDCI (Thumb Screws), to 68 Pin Female SCSI (Thumb Screws), 36"
-
Product
RS-232 Auto Powered Line Driver
Model 201
-
FEATURES: Operates with only Pins 2(TD), 3(RD), & 7(GND); Screw Terminals and RJ-11; DTE/DCE Switch; Built in Surge Protection; Male or Female RS-232; 19.2 KBPS, Full Duplex, 2.1 Miles. The Model 201 RS-232 Auto Powered Line Driver requires only TD, RD, and signal ground for power and full duplex operation up to 19.2 K BPS.
-
Product
Digital Torque Screwdriver
NDID-150CN
-
Tightening of screws and bolts and final checks. Digital torque driver idling type. An idling type torque driver that can record the torque and the number of tightening by tightening until it makes a "click" sound. When the specified torque value is reached, the clutch automatically disengages and idles, so there is no need to worry about over -tightening.
-
Product
sbRIO-9223, Non-Enclosed, ±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
785480-01
Voltage Input Module
Non-Enclosed, ±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO-9223 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The sbRIO-92233 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the sbRIO-9223: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
Product
Wire Damaged Tester
WDT-1
-
This equipment is designed and manufactured according to corresponding regulation in standard IEC884-1, GB299.1-96, GB16915.1-97 and other electronic accessories relevant standard. Mainly used to test damage degree of fixed connection components lead wire of with thread clamping type and no screw terminals, so as to inspect whether it can withstand mechanical stress during normal use.Specification: • Power supply: AC220V 50Hz • Test rate: 10±2r/min (GB16915.1-97: 12 ±1r/min) • Rotating radius: 100mm • Test distance: 250~500mm adjustable • Test numbers (Number of rotating): 0~999999 any set • Mass: 0.3KG, 0.4KG, 0.7KG, 0.9KG, 1.4KG, and 2.0KG (GB16915.1-97: 30N, 40N, 50N, 60N each of 2 pcs) • Stations: 2 • Dimension: 1200×1400×400 (mm) • Remarks: The mass and rotating radius can be optional as per customer requirements.
-
Product
Cable Assembly, 68 Pin Male VHDCI (Thumb Screws), to 68 Pin Female SCSI (Thumb Screws), 36"
515109114
Cable Assembly
Cable Assembly, 68 Pin Male VHDCI (Thumb Screws), to 68 Pin Female SCSI (Thumb Screws), 36"
-
Product
Optical Measurement
-
• Vertical optical measuring machine for static and dynamic measurement of various elements on small cylindrical parts.• The parts can be mounted between two centres or held in place using various accessories.• Attractive design and robust construction with many new features: New touch screen control panel for easy operation directly at the workplace, bi-telecentric optical system, high resolution CMOS camera, precision sliding headstock with integrated and protected daily standard, quick and easy accessory changing system, integrated temperature sensors, dynamic LED indicator of the general status of the measured part (GO/NG) and operator messages. Equipped with an exclusive optics tilting system.• Machines specially designed to measure threads such as, parallel, trapezoidal, conical, round, square, conical, worms, ball screws, bone screws, dental implants, etc.• Reflex SCAN+ concept for measuring parts without prior programming at the touch of a button• Delivered complete with a PC and the Reflex SCAN+ software, which allows a multitude of elements to be measured easily and intuitively.
-
Product
SCB-100A Noise Rejecting, Shielded I/O Connector Block
785024-01
Terminal Block
100-Pin Female SCSI to 100-Pin Female Screw Terminal, DIN Rail, Wall, Pane Terminal. Block The SCB-100A is a shielded I/O connector block for interfacing I/O signals to NI data acquisition devices with 100-pin connectors. Combined with shielded cables, the SCB-100A provides rugged and protected signal connectivity. It has a mechanical enclosure that features a magnetic removable lid and pinout diagrams. It also includes pane, wall, and DIN Rail mount options.
-
Product
Heavy Load Ball Screw with Caged Ball Structur
HBN
-
Heavy Load Ball Screw with Caged Ball Structure. Heavy load ball screws with the caged ball structure (HBN model) drastically improve the rated load compared to the conventional products by utilizing the optimum internal structure for use in heavy load condition. In this model, the caged ball structure is adopted between balls to eliminate collisions and mutual frictions of the balls and improve the lubricant maintenance. This modification brings about a longer lifetime under heavy load conditions.
-
Product
9-Pin D-Type Connector Block
92-965-009-F
Connector Block
This connector block provides a simple method of connecting to 9-Pin D-Type connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage.
