Screw
See Also: Thread, Linear Actuators
-
product
Sensor Clamps
ULP-CP
Use a single clamp for the Sensor with a single #10-ANSI screw for one-hole fixing.
-
product
Serial RS-232 Expansion Connector Accessory for USBHub3c
Used for connecting a serial RS-232 interface to the control the USBHub3c through the expansion interface connector. Screw terminals are provided for the RS-232 interface. While this board provides for wiring connections, a host machine external to the USBHub3c is required for this control interface.
-
product
Emergency/Panic Button
ENVIROMUX-EBS
Sends activation signal when button is pressed. For normally closed or normally open circuit connections. 2-wire interface. Screw terminal. Maximum cable length: 1,000 ft (305 m). Dimensions WxDxH: 1.7x2.9x4.6 in (43x74x117 mm). Regulatory approvals: RoHS.
-
product
Module Accessory Kit, 26 4-40x .750" Socket Head Cap Screws
510109359
Module Accessory Kit, 26 4-40x .750" Socket Head Cap Screws
-
product
Module Accessory Kit, Quantity 26 2-56 x .50" Flat Head Phillips Screws Stainless Steel
510109376
Used with modules: 510104307, 510170101 and 510170102.
-
product
MAX31855 K-Type Thermocouple Sensor Breakout
SEN-30001-KDP
Breakout board for the MAX31855K digital thermocouple interface IC. Measured temperature range is -270C-1372C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header and four mounting holes for standoffs and 4-40 screws. It does not contain a mini thermocouple connector.
-
product
Cable Assembly, 68 Pin Female SCSI (Thumb Screws), to 68 Pin Male SCSI (Spring Latch), 36"
515109120
Cable Assembly, 68 Pin Female SCSI (Thumb Screws), to 68 Pin Male SCSI (Spring Latch), 36"
-
product
Cable Assembly, 68 Pin Female SCSI (Thumb Screws), to 68 Pin Male SCSI (Spring Latch), 18"
515109119
Cable Assembly, 68 Pin Female SCSI (Thumb Screws), to 68 Pin Male SCSI (Spring Latch), 18"
-
product
Varactor Tuned Gunn Oscillators
Varactor tuned Gunn oscillators utilize high performance GaAs Gunn diodes and various cavity configurations to deliver moderate output power with low AM/FM noise and harmonic emissions. The oscillators are specially designed for a broader tuning bandwidth and an electrical tuning capability. The standard offering covers the frequency range of 8.2 to 110 GHz and features a self-locking set screw for fine frequency setting. While standard models offer a waveguide interface, a coaxial interface is also available. The performance of the oscillator can be further enhanced by adding an isolator, Gunn oscillator modulator/regulator, and temperature heater.
-
product
Enclosure, 25 Module, Large
410112368
The 25 Module Enclosure, Part # 410 112 368 is made of aluminum, painted black and secured to the ITA by eight socket head cap screws (included). It is equivalent in length to the 50 module enclosure with a depth of 6" and handles on each side.
-
product
Light Meters
Meter reads from 0 to 1,999 foot-candles (resolution 0.1 to 1). Bright 1/2-inch-high digits make it an easy to read pocket light meter. The simplicity of the two-button operation eliminates the need to refer to directions. Functions are on/off, and range. The meter can be zeroed with the simple turn of an adjustment screw
-
product
Actuators, Adjusters, & Transducers
We offer a wide range of adjustment screws, micrometers, and kinematic positioners, as well as stepper motor, DC servo, high-precision piezo inertia actuators, and voice coil actuators. Additionally, our piezoelectric offerings include modular, screw, and replaceable-tip piezoelectric actuators, as well as Langevin transducers for ultrasonic welding applications. A wide variety of piezoelectric chips and stacks are also available.
-
product
Module Accessory Kit, Quantity 26, 4-40 x .625" Captive Socket Head Cap Screws
510109366
Used with modules: 510104135, 510104136, 510150115, 510150116, 510150130, 510150136, 510150137, 510150147, 510151105, 510151106 and 510151124.
-
product
Module Accessory Kit, Quantity 26, 4-40 x .56" Socket Head Cap Screws
510109619
Used with modules: 510104120, 510104123, 510104150, 510104307, 510104319, 510108125, 510108126, 510108245, 510108263, 510108281, 510170101, 510170102 and 510171101.
-
product
Enclosure, 50 Module, Hinged Cover Plate, 4" Deep
410112199
The Enclosure for the 50 module ITA is made of aluminum, painted black and secured to the ITA by eight socket head cap screws (included). The top of the enclosure is a hinged cover plate with quarter turn hardware that provides easy access to the ITA’s wiring when required.
-
product
64-Channel Form A General Purpose Switch for 34980A
34939A
The Keysight 34939A is a high density general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 64 independent single-pole, single-throw (SPST) relays that can switch 1A and carry 2A. This module can be used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. The relays are 100V, 1A contacts and can handle up to 60W. Standard 78-pin Dsub connectors allow for use with standard cables, screw terminal blocks, or mass interconnect solutions.
-
-
product
sbRIO-9222, Non-Enclosed, ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
785479-01
Non-Enclosed, ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO‑9222 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The sbRIO‑9222 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the sbRIO‑9222: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
product
Dual MAX31865 PT-100 RTD to Digital Breakout
SEN-30202-PT100
Dual channel breakout board for the MAX31865 RTD-to-Digital converter from Maxim. Two breakout hardware configurations are available standard, designed to interface with either the PT100 or PT1000 platinum RTDs. For non-standard applications, including thermistors, custom hardware configurations can be accommodated. Contact Technical Support for more information. RTD devices may be wired in 2, 3 or 4-wire configurations using the 4-pin screw terminal input. The MAX31865 breakout is interfaced via 3 or 4-wire SPI with a data-ready output for specific operating modes. An LDO and a high-speed level shifter are included to allow interfacing with microcontroller devices between 3.0V and 5V (all Arduinos, Raspberry PI, etc) without sacrificing device performance.
-
product
Wire Piercing Clips
619
This new clip makes wire piercing much easier. Just slide the wire into the cradle and screw the pin down into the wire. This method is clean and leaves minimal wire damage. If you have to proceed to pierce the wire, do it the right way with 619.
-
product
68-Pin SCSI Micro-D Conn Block DIN
40-966-068-M
Suitable for mounting on DIN Rails this connector block provides a simple method of connecting to 68-Pin SCSI Style Micro D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
25-Pin D-Type Male Connector Block
92-965-025-M
This connector block provides a simple method of connecting to 25-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximize copper cross-sectional area and insulation properties. Users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
product
Economical Hydraulic Manual Universal Testing Machine
WEW-D Series
Jinan Testing Equipment IE Corporation
WEW-D series hydraulic manual UTM is suitable for testing tension, compression and other strengths of various metallic or nonmetallic materials with high strength. The hydraulic manual UTM is capable of testing the characters of materials on physical & technology properties. As a manual control & economical UTM, the hydraulic manual UTM is with reasonable and reliable configurations (load cell or pressure transducer, extensometer, photoelectric encoder, servo motor & driver, standard screws), which can satisfy ordinary testing requirements. Digital controller and computer with software can be equipped on this machine to realize the test date/curve collecting and process. The hydraulic UTM of economical type is easy to operate and is versatile in the applications of metallurgy manufacturers such as steel mills & alloy, reinforced bar etc.
-
product
Cable Assembly, 68 Pin Male VHDCI (Thumb Screws), to 68 Pin Female SCSI (Thumb Screws), 36"
515109114
Cable Assembly, 68 Pin Male VHDCI (Thumb Screws), to 68 Pin Female SCSI (Thumb Screws), 36"
-
product
5VDC Sensor Converter, 5VDC, 15mA
ENVIROMUX-S5VDC-5V
External RJ45 device monitors up to two linear DC sensors, 0VDC ~ 5VDC. Output for each sensor: 5VDC, 15mA. Connector: Screw Terminal, 8-position. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Includes Mounting Hardware. Powered by ENVIROMUX-2D/5D/16D. MTBF: 1,956,288 hrs. Compatible with ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
product
Connector Block, 50-Pin D-Type, Female
40-965A-050-F
The 40-965A-050-F connector block provides a simple method of connecting to 50-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties. Connector blocks have higher losses than a cable connection and the breakdown voltage is controlled by clearances to the metal shell. The metal shell includes an internal insulation barrier under the carrier board.
-
product
Cable, 10 Pos Combicon to Pigtail, 1 Meter
190656-01
The SH10M-10F Cable, sometimes referred to as SH10F-P, connects C Series DAQ devices with a 10-pin screw terminal to open signal wires. The SH10M-10F Cable is offered in different lengths.
-
product
Vision Measuring Projector
Sinowon Innovation Metrology Manufacture Ltd.
◆ The lifting system adopts linear guide rail and precision screw drive, which makes the lift drive more comfortable and stable;◆ With precision toothless rod and fast movement locking device, ensure return error is within 2um;◆ High accuracy A optical scale and precision working stage, ensure machine accuracy is within 3+L/200 um;◆ HD zoom lens and HD color digital camera, ensure clear image without distortion;◆ With programmable surface 4-ring 8-division LED cold light and contour LED parallel illumination, it can control the brightness of the 4-ring 8-division independently;◆ With powerful iMeasuring2.1 software system , to enhance the control quality;◆ Optional imported contact probes and 3D measuring software, it can help upgrade the machine to be coordinate measuring machine;◆ Optional FexQMS measurement data analysis and real-time monitor software, enhance process control, reduce material consumption;
-
product
DIP Header with Coined Contacts
Series 600
DIP Headers with Coined Contacts. Aries offers a full line of DIP headers, available with either coined or screw machine contacts. Consult Data Sheet No. 12035 for screw machine contacts. Snap-on, protective covers are available for all sizes shown below and accommodate .125 [3.18] to .750 [9.05] component heights. Consult Data Sheet No. 12033 for protective covers.
-
product
Voltage Monitoring, Timer Delay-on -off, 4 Pole
MTDV4 Relay
Plug-in electronic voltage monitoring relay with optional delay-on and delay-off timer function and four change-over contacts. The delay time is adjustable with a lockable knob (either delay-on or delay-off, the other delay is fixed). The relay can also be supplied with fixed time delays (no knob). The pull-in voltage and drop-out voltage are both adjustable via internal screws. The relay can also be supplied with a fixed pull-in and drop-out voltage. Suitable for monitoring DC voltages.
