Showing results: 1141 - 1155 of 2667 items found.
-
Micro Centurion II -
Raytech AG
Raytech Digital Micro ohm meter, Micro-Centurion II, was designed for high degree of accuracy to measure very low resistances. This technology was then packed into a portable test system to be used by apparatus manufacturers, rebuild shops, and electrical maintenance crews. This intelligent system has an easy to use operation screen, which allows quick selection of the current level and resistance level to be measured.
-
VE2729XAU -
Vasavi Electronics
Its a Microprocessor Based 200KHz Automatic Transformer Tester with inbuilt 20 Pin Channel Scanner for Automatic Switching and Testing Coils & Transformers (Ferrite) with Max. 20 PINS. Test Parameters : -> Inductance (L)-> Leakage Inductance (Lk)-> Capacitance (C)-> DC Resistance (Rdc)-> AC Resistance (Rac)-> Turns Ratio with Winding Polaity-> Quality Factor (Q)-> Impedance (Z)
-
SE-1004B+ -
KILTER ELECTRONIC CO.,LTD
●For AA, AAA size Alkaline ,Ni-MH ,Lithium batteries●Three mode: Charge , Discharge & Internal Resistance●Capacity Range: 4Ah●Prevent over heat while charging●Auto alarm at the end of charge or discharge ●Display charge voltage, capacity(Ah) , Intenal Resistance(mΩ) ●Used for mobile phone or camera battery ●Accessories: battery clamp, power adapter
-
N1427B -
Keysight Technologies
The N1427B is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It comes with a separate triaxial (special screw-type) female connector and a High Voltage BNC (special type) female connector. This allows terminal configuration to be converted to any other configuration. Therefore, custom test fixture can easily be constructed. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1427B to the B2985B/87B.
-
HH2704 -
Colluck Company Limited
Basic Accuracy 3.0%. 5 Functions / 17 Ranges. Voltage test up to AC500V and DC1000V. Current test up to 250mA. Resistance test R X 100Ω, Test Batteries 1.5V "AA". Power: 1 x 1.5V "AAA" battery
-
HH2702 -
Colluck Company Limited
Basic Accuracy 4.0%. 5 Functions / 18 Ranges. Voltage test up to AC750V and DC 750V. Higher Current test up to 10A. Resistance test R X 1KΩ. Test Batteries 1.5V and 9V. Power: 2 x 1.5V "AA" battery
-
MODEL KM 885 -
Kusam Electrical Industries Limited
• VFD V & Hz readings• LCD Backlight Display• Record MAX/MIN regular readings.• Display Hold Function.• Dual Display +Hz readings.• Relative zero mode.• LOCK-Test mode for Insulation Resistance• BeepJack™ audible & visible input warning.• High resolution 60.00mV & 60.00 ranges.
-
93-022-101 -
Pickering Interfaces Ltd.
The 93-022-101 104-pin D-type Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions. The tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
93-002-101 -
Pickering Interfaces Ltd.
The 93-002-101 200-pin LFH Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions.. The tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
93-006-101 -
Pickering Interfaces Ltd.
The 93-006-101 78-pin D-type Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions. The tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
DF2 -
North Atlantic Industries
Function module DF2 (Enhanced Version) multi-mode transceivers with 16 programmable I/O channels. Differential transceivers increase resistance to noise by creating two complementary signals. These complementary signals produced on balanced lines double noise immunity by creating lower power requirements due to lower supply voltages.
-
A.T.i. Software GmbH
Analog components (resistance, capacitance, inductance, diodes, transistors, etc.) as well as complex digital components can be tested in the ICT. Compared to other test methods (e.g. flying probe), the in-circuit test enables very short test times (= high assembly throughput) combined with a very high test coverage.
-
PDRM-10A -
Amperis sl
The PDRM-10 A ohmmeter, with a range of 0.01µΩ to 200 Ω is currently the most accurate and highest resolution ohmmeter on the market, and at only 860 g it is also the lightest and most compact. All this has made it the standard low resistance ohmmeter in many electrical companies, industries and assembly companies. It has a resolution of 0.01µΩ.
-
REOLOAD 310 -
REO Ltd.
A three phase load bank rated for 48kW, with fan cooling. The front panel layout includes a switch panel for configuring the separate resistor modules to give the required resistance and current range. There are also digital panel meters for displaying the phase voltages and currents. An interface for PLC control is also provided.
-
MODEL KM 887 -
Kusam Electrical Industries Limited
• VFD V & Hz readings• LCD Backlight Display• Record MAX/MIN regular readings.• Display Hold Function.• Dual Display +Hz readings.• Relative zero mode.• LOCK-Test mode for Insulation Resistance• BeepJack™ audible & visible input warning.• High resolution 60.00mV & 60.00 ranges.