Showing recent results 1 - 15 of 130 products found.
-
96040A Series - Fluke Calibration
The 96040A RF Reference Source enables you to simplify your RF calibration system by replacing many of the instruments and accessories that make up your current system.
-
Fluke Calibration
The 27 GHz 96270A and 4 GHz 96040A Low Phase Noise Reference Sources are designed specifically for RF calibration, featuring a calibration-oriented interface, precision signal level and attenuation, high signal purity and precision low distortion modulation. Both instruments simplify the process of RF calibration by reducing the amount of equipment and simplifying the calculations required.
-
ERS - Laplace Instruments Ltd.
The ERS is a comb generator that radiates RF continuously every 2MHz over the range 30MHz - 1000MHz. Each 2MHz peak is precisely measured during the calibration process with the ERS orientated both vertically and horizontally. These measurements are correlated against a 3m OATS such that any fully implemented CISPR16 site, measuring at 3m and using height scanning, will read the same.
-
-
VSQ Series - Teseq AG
Radiation source for the frequency range from 30 MHz to 1 GHz. It consists of a battery operated comb generator RSG 1000 and biconical broadband antennas DPA 4000. The comb generator is supplied by a high stable temperature compensated crystal oscillator (TCXO) and generates a frequency spectrum with a line spacing of 1 MHz, 5 MHz or 10 MHz. Combined with an antenna the generator represents a precise radiation source.
-
HGH Infrared Systems
Blackbodies are reference sources used for testing infrared systems. They are required in industry for calibration of pyrometers, infrared line scanners or cameras. In laboratories, they are part of benches for characterisation of complex optronic systems. HGH offers a wide range of blackbodies to cover all Customers needs.
-
Qref - QSources BVBA
Precision omni-directionallity in all directions, horizontal and vertical plane. This source has a frequency range of application between 100 and 8000 Hz (third octave bands) Despite only weighing 1.4 kg and having a diameter of 105 mm, it produces a maximum sound power level of Lw 104 dB.
-
96270A - Fluke Calibration
The 96270A RF Reference Source is the simplest, most accurate and cost-effective single instrument for calibrating spectrum analyzers and RF power sensors and more, up to 27 GHz.
-
515 - Clarke-Hess Communications Research
The Model 515 High Accuracy AC Reference Generator fills a need for a relatively low cost and practical solution for supplying a reference excitation to typical LVDT and Synchro/Resolver transducers. The Model 515 has built-in load sensing which, in effect, yields "zero" output impedance and virtually eliminates the effects of fluctuating output loads. With up to 15 VA of output into loads with as much as 80 of phase shift, the Model 515 is ideally suited to driving inductive loads.
-
CGE - York EMC Services Ltd
These reference signal source generate a broadband radiated and/or conducted output up to 40 GHz. When used as a verification reference source, the known output allows unknowns within systems or components to be measured or calculated.
-
HGH USA
Blackbodies are reference sources used for testing infrared systems.
-
MKS Instruments
These general performance Baratron® differential capacitance manometers measure the difference in pressure between the inlet tube and the reference cavity. The reference cavity can be connected to any pressure or vacuum source, or be open to local atmosphere.
-
PAT01 - Ponovo Power Co., Ltd.
PAT01 is a power amplifier control unit that controls timing output and reference signal test source for power amplifier.
-
ST-NG1 - Radio Design Labs
The ST-NG1 is the ideal choice where random white or pink noise is needed. It is suitable either as a reference noise source for audio measurements or as a masking noise source in engineered sound or counter-intelligence applications.
