-
product
PCIe FPGA Carrier For FMC, Virtex-7
PCI516
The PCI516 is based on the Xilinx Virtex-7 690T, which provides 3,600 DSP slices, 52,920 Kb RAM and 690,000 logic cells. The FPGA interfaces directly to the FMC DP 0-9 and all FMC LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. It also has interface to three DDR3 memory channels (64-bit wide and 16-bit wide). This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host. The unit has x8 PCIe edge connector routed to the FPGA PCIe Gen3 hard IP block. In addition, 16 uncommitted connection pairs are routed to a dual x8 expansion connector, providing direct connectivity to a neighbouring FPGA (e.g. via Aurora, 10 G/40 G, SRIO, PCIe) without the need to go through the host.
-
product
NVRAM
ST's non-volatile RAM (NVRAM) products protect data, even in the absence of power, and have fast RAM write speeds with unlimited endurance.
-
product
8 SE Or 4 Diff. Input Channels, 8 Analog Output Channels, PCI Express
APCIE-3121-8-8
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
Low Power SRAM
Renesas is the worldwide #1 Low Power SRAM supplier with a full lineup and well balanced long term support. High density and high performance RAMs using Renesas's original technology, for example the Advanced LPSRAM new memory cell concept are offered.
-
product
Intelligent Interface Card
IIB-1553-PC104
The IIB-1553-PC104 is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for PC compatible computers, with 1553A, 1553B, McAir and STANAG 3838 variants in one card. The IIB-1553-PC104 supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with powerful multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a single, dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. PC memory space utilised by the board is selectable. The board is supplied with C drivers in source code and Windows menu driven software as standard
-
product
MIL-STD-1553 MCH
M4K1553MCH
The M4K1553MCH interface module for the multimode, multiprotocol, Excalibur 4000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.The M4K1553MCH contains 32k x 16 of dual-port RAM for Data blocks, Control registers, and Look-up tables. All Data blocks and Control registers are memorymapped and may be accessed in real time. The dual-redundant 1553 module may be programmed to operate in one of four modes of operation: Bus Controller, Remote Terminal, RT/Concurrent-Bus Monitor, and Bus Monitor. The M4K1553MCH comes complete with Windows software, and a C driver software library including source code.
-
product
PCI Data Acquisition Boards
AD8S-100DMA Series - Single low-spur 8-bit, 100 Ms/s
Model AD8S-100DMA is similar to the AD8-100DMA, has a single low-noise eight-bit 100MSPS A/D converter and can acquire up to 100 MS/s on a single channel into the host system's RAM. Drivers for 64 bit Linux and Solaris operating systems included.
-
product
Touchscreen Panel 1.9GHz PC for Harsh Environments
PPC65B-1x series
Advanced IP65-rated Panel PC delivering high reliability and an extended operating temperature range in a thin, fanless design. The PPC65B series offers a rugged design for extreme environments and industrial IoT applications ranging from -20ºC to +70ºC. 1.9 GHz Quad-Core Intel® Atom™, E3845 processor, Up to 8 GB of RAM, Supports Linux, Windows 10 Operating Systems, Fast Graphics at High Resolutions • Five-wire resistive touchscreen • Resolution: 1024 x 768 / 1280 x 1024; 5 screen sizes 10.4" - 19".
-
product
Memory
Renesas offers MIL-STD-883-compliant CMOS random access memory (RAM) and CMOS programmable read-only memory (PROM) devices that are that are qualified to QML Class Q military standards.
-
product
Module Spectrum
nRF51822 Series
Raytac nRF51822 module provides 16K & 32K RAM option with Chip Antenna & PCB Antenna for selection.
-
product
3.5" Embedded SBC With Intel® Celeron® J1900 Processor, LVDS/VGA/HDMI, Dual LANs, Audio And ZIO
CAPA843
The CAPA843, a fanless 3.5-inch embedded board, features quad-core Intel® Celeron® processor J1900 SoC (codename: Bay Trail). A pair of SO-DIMM sockets supports up to 8GB of DDR3L 1066/1333MHz RAM. The compact size embedded board CAPA843 was designed with emphasis on expandability, offering two full-size PCI Express Mini Card slots, as well as an exclusive Axiomtek ZIO connector. With excellent thermal design, the 146 x 102mm embedded SBC can handle operating temperatures from -20°C to 70°C, and runs on +10V to +24V DC input. The 3.5” fanless embedded board provides three display interfaces with dual-display operation: HDMI, LVDS and VGA. The Axiomtek CAPA843 is an excellent choice for applications in IoT/M2M-related, industrial control, self-serve terminal, gaming, digital signage, POS, and kiosk.
-
product
CPCI Based 486DX4 Board
MS 1501
- CPCI/PXI Bus Interface, 6U form factor- Watchdog Timer- Hot Swap Facility- PCI Bus Rear IO Expansion for External Bus Interface- Debugging Monitor interface through RS232- JTAG interface for 486 for boundary scan test- Power Source through the CPCI connector J1 (±12V, +5V, 3.3V)- 1Mbytes of Dual Port RAM, 256Kbytes of STATIC RAM- 1MBytes of FLASH PROM- RS232, RS422 Serial Interface- Intel 486DX4 operating at 100MHz frequency at the core- Driver interface for Windows2000/XP/VISTA and LINUX/RT LINUX OS
-
product
PCI Express Ultra-fast Data Acquisition Add-In Cards
Ultraview's PCIe series of data acquisition add-in cards are complete A/D systems on a single PCIe add-in card. These boards incorporate up to 8GB of on-board RAM with up to 7GB/sec on Kintex 7 (up to 1.4GB/sec on Virtex 5) typical PCIe bus transfer rates enabling full-rate acquisition for long durations. All boards in the PCIe series are supported with the same user software allowing users to select the bit resolution and acquisition rate appropriate for a given application and then easily re-use the same software on a different part. Included with each card are graphical waveform viewers, example user software with source code included, and device drivers for Linux and Windows. The example software is intended to allow users to quickly prototype and develop their applications.
-
product
SMARC V1.0 SoM With IMX6 Quad/DualLite 800 MHz (Industrial) SoC, 1GB RAM, 4GB EMMC, GbE LAN, Audio, CAN, MIPI And PCAM
SCM120
*SMARC 1.0 (82 x 50 mm)*Ultra low power consumption Cortex™-A9*2 CAN 2.0B*24-bit TTL signal*LVDS/HDMI 1080P*10/100/1000 Mbps Ethernet*Linux3.0.35/Android 4.3*Audio
-
product
Express Card
DAS-429ExCARD/RT10
Both cards contain 64 Kbytes of true dual-port RAM, for data blocks, control registers and Look-up table.The card's small size (54 millimeter wide) and suitability for Express Card compatible notebook computers make it a complete solution for developing and testing ARINC-429 interfaces and for performing system simulation of the ARINC-429 bus, both in the lab and in the field.The cards are supplied with C drivers, including source code, Mystic Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
product
Acute 4GS/s 68 Channel Logic Analyzer With 32Gb Memory
Acute LA3068B+
*LA3000E+/B+ series logic analyzer*PC-based*68 / 136 channels*USB 3.0 interface, 12V power adaptor*4GHz Timing Analysis / 250MHz State Analysis*32Gb RAM*Active Probes*Logic, State, Protocol triggers
-
product
MIL-STD-1553 One-Channel PCI Board
BRD1553PCI-1
The P-Orchestra™ is a one-channel MIL-STD-1553B PCI board, which includes Bus Controller (BC), Remote Terminal (RT) and Monitor (MT) capability. The board can be used as a hardware and software development kit for IP cores. P-Orchestra channels are software compatible to DDC® Enhanced Mini-ACE® components and architecture, with 16K word of internal RAM.
-
product
8 CHANNELS ARINC 429 Simulator Analyzer Tester
CIC429
The CIC429 is a full featured, high performance Serial bus Simulator Analyzer Tester developed by Andor Design for test and simulation of ARINC 429 or similar Avionic buses. The CIC429 is designed as a 5/8 size plug-in card for an ISA bus. An on board microprocessor off loads the host by organizing the data in a predefined structure in the dual port RAM. Programming the CIC429 consists of changing this data, which can be done on the fly for real time applications
-
product
PCI Data Acquisition Boards
Ultraview''s PCI data acquisition add-in cards are complete data acquisition (A/D) and control (D/A) systems on a single PCI Bus card. Ranging in speed from dual 14 and 12-bit 1-25MSPS boards up to 1500MSPS 8-bit boards with 8GB/16GB of on-board RAM. All cards come with graphical waveform viewers, example user programs (source code included) and device drivers for Linux or Solaris, allowing users to quickly prototype and develop their applications.
-
product
Memory Tester
RAMCHECK
RAMCHECK is our most advanced memory tester and is the latest in our product line. Highly modular and user friendly, it redefines the capabilities of an affordable and portable ram checker.
-
product
Intelligent Double Sized H009 Interface Module for Excalibur 8000 Family of Carrier Boards
M8KH009
The M8KH009 is an intelligent, double-sized, H009 interface module for the multimode, multiprotocol, EXC-8000 family of carrier boards. The M8KH009 provides a complete solution for developing and testing H009 interfaces and performing system simulation of the H009 bus, according to the standard H009 protocol. Each module of the M8KH009 contains 32K x 16 dualport RAM for Data Blocks, control registers, and Look-up tables. In addition, the module contains another 32K x 16 dual-port RAM for a Concurrent Monitor. All data blocks and control registers are memory mapped, and may be accessed in real-time. Each of the independent, dual-redundant M8KH009 modules may be programmed to operate in one of three modes of operation: Central Control Complex (CCC) mode with Concurrent Peripheral Unit operation (1–16 PUs), Peripheral Unit mode (Multiple – up to 16 PUs) and Bus Monitor mode. In addition, the module can simultaneously operate as an independent Internal Concurrent Monitor in CCC, Multiple PU or CCC/Concurrent PU modes.
-
product
16-bit, 200KHz, 16SE/8DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3116-16
The APCI-3116 is a 16-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3116, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
product
PXI Controller
The ADLINK PXI embedded controller, based on the Intel® processor family, is specifically suited for hybrid PXI-based testing systems, delivering a rugged and stable platform for a wide variety of testing and measurement applications. The PXI embedded controllers sport integrated CPU, HDD or SSD, and RAM, and provide ample interface flexibility, including one Gigabit Ethernet port for LAN connection and one for controlling LXI instruments, USB ports for peripheral devices and USB instrument control, and a Micro-D GPIB connector for GPIB instrument connection.
-
product
PCIe FPGA Carrier For FMC, Virtex UltraScale™
PCI595
The PCI595 is based on the Xilinx XCVU440 Virtex UltraScale FPGA, which provides 2,880 DSP slices, 88.6 Mb RAM and 5,541,000 logic cells. The FPGA interfaces directly to the FMC DP 0-9 and all FMC LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. It also has interface to one DDR4, 64-bit wide, with 8 GB total memory. This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host.
-
product
32 Channel Driver
The MultiChannel RF Driver is a 32 channel signal generator / amplifier intended to drive multchannel acousto-optic cells such as the Harris H-601. The driver can be operated either as an RF amplifier, providing 32dB of gain or as a high power signal generator making use of a dedicated 1GSPS, 14bit digital synthesizer on each channel. Modulation can be performed through the use of the internal source, external global input, external individual input, or programmable 16K sample RAM lookup table.
-
product
RMC-8354, 2.8 GHz, 1U Rack-Mount External Controller for PXI
781650-33
2.8 GHz, 1U Rack-Mount External Controller for PXI - The RMC‑8354 is a 1U rack-mount controller for PXI‑ or PXI Express‑based systems intended for test and measurement applications requiring a rack-mount controller. It features an Intel Core i7‑860 quad‑core processor and offers DDR3 RAM, dual onboard Gigabit Ethernet, and removable SATA II hard drives. It also supports RAID arrays, which allows multiple hard drives to be configured for either high‐speed data streaming or data redundancy.
-
product
Capture Software
Easy to use software, windows based, that offers to record, view and combine up to 9 cameras in one setup. The software is compatible with a wide range of cameras, providing the option to integrate your own cameras into an imaging setup easily. It features recording to RAM or Hard drive, a Triggered recording, and timelapse recording.With the external Application Programming Interface (API), Capture can be customised and integrated in an existing setup. Through the API, you have access to device settings, recording parameters and image data.
-
product
16-bit, 200KHz, 16SE/8DIFF Isolated Analog Input Board
APCI-3016-16
The APCI-3016 is a 16-bit analog input board for 3.3 V and 5 V PCI systems, with optical isolation and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.
-
product
Real Time Switch
IM1754G
Real Time Switch is a real time timer which can be used to switch electrical appliances like street lamps, garden lights, corridor lights, neon signs etc as per time of the day. The timer has built in almanac timings fixed in nonvolatile ram so that the user does not have to programme the unit from time to time. This has added advantage over daily dial or weekly timers. Timer provides two outputs to drive contractors of different ratings. These outputs can be used with different combinations to achieve desired output. Timer is provided with manual override facility. Optional detachable external keyboard unit provided to avoid unauthorized access.
-
product
MIL-STD-1553 Four-Channel VME Board
BRD1553VME-4
The V-Orchestra™ is a four channel MIL-STD-1553B board, which includes Bus Controller (BC), Remote Terminal (RT) and Monitor (MT) capability for each channel. V-Orchestra channels are software compatible to DDC® Enhanced Mini-ACE® components and architecture, with 64K word of internal RAM.
